IARC 207 Wiki - User contributions [en]

Spring 2017 visit

2017-06-07T15:52:35Z

10.91.4.151: /* at toolik */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*<s>change notes in program where measure pressure to change CS100 to CS106
**remove sea level offset</s>
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??
*fix some of torn blue mesh panels on Wyoming shield

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet
*snow depth data
*go through enclosure in Brie's office
*figure out how to VPN into lognet
notes from 6/5/17
*screw in more secures for pluvio cable
*read about pluvio heater
*read about power for garden cam
*remove evap temp from program
*change program and wiring for HMPs
*change CNR4 heater?
*CMP6 heater?
*label all wires better
*move snow sensor away from tower?
*think about garden cam
6/7/17
*left garden cam batteries in brie's office

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

2017 NGEE June Nome Trip

2017-06-07T03:40:14Z

10.91.4.151: /* bring */

* @ [[Kougraok M64]]
** soil pit (fall deployment)
*** soil moisture @ 5, 10, 20, 30, 40 cm bgs
** soil thermal conductivity @ 10, 20, 30, 40 cm bgs
** soil temperature @ 10, 20, 30, 40 cm bgs
**** soil heat flux near base of active layer & plant / soil boundary
*** 1.5m soil temperature profile
*** snow depth @ tripod
*** snow depth away from tripod
*** interval camera
*** 4 component radiation
*** Spectral response sensors: NDVI & PRI up looking and two vegetation communities
*** 1.5m Air temperature, Relative Humidity, & Dew Point Temperature
*** Wind speed and direction at 3m
*** summer precipitation
* @ Teller Bottom
** send one more program to fix 5cm bgs soil moisture out of range array error

Old Atlas sites:
* @ C1 Grid
** We have a CNR4 for this site I believe.
** HMP155 has been changed out here
** fix MRC portion of program last change we screwed something up and sent the 2011 program with a but rather than the 2012 version.
* @ C2 Blueberry
** Replace the LW Transmitted cable, will need to bring the whole package from Fairbanks
** 10meter AT/RH has not worked since 2011
* @anvil scool
**propeller for wind sensor

===bring===
**radios to download K sites remotely if necessary
**copies of permits?
**radios for base station (in basement)
**drill bit for VAPT probe
**zip ties
**hose clamps
**TOOL BAGS
**CABLE BAG
**putty
**resistor for VAPT
**fish tape
**measuring tape
**anti corrosion goo
**extra nuts, washers, etc
**extra ubolts
**guy wire and findings
**inReach, sat phone
**sledge hammer
**sleeping bag liner?
**torpedo and circle level
**CFM100+card
**field books, pencils, pens sharpies
**duct tape
**splicing tape
**electrical tape
**BUG SHIRT

===todo===
**Bob: figure out base radio in Nome
**book housing: campsite? NPS bunkhouse: 1800.471.2352 or go downtown their office is the Sitnasauk building on front street?
**ship things
**find all the stuff for tower
**look@ data bob recently downloaded from teller
**look at data streaming in on NGEE data
**which sites need new batteries?
**replace wire on solar panel?
**wire up box
**figure out cross arms
**Do i need two mux's?
**make list for bob to look for in UAF storage (trail matt?, hose clamps for tipping bucket, tripod, buy mast if have time, batteries)
**TA's
**find other sr50a
**safety plan

===to buy===
*Alaska Steel
**threaded coupler for 1 to 1.25 pipe for Wind sensor
**cross arms (8ft rad[nurailT], 5 ft tower snow[nurailT], 4,4,5,3 ft far snow[3nurailT], 4,4,3ft tipping[2nurailT], 5 ft far rad
***7nurail 1.25 T fittings, 8ft, 3*5ft, 4*4ft, 2*3ft
**nurail fittings
*campbell
**2 new propellers (1 for anvil school, 1 for teller top)
**20 SR50a transducers
**CNR4 desiccant. how many (Teller top, teller bottom, 4 in barrow)?
**CFM
**long SR50a cable
*home depot
**conduit
**fuse and holder
**tennis balls or something to cover pokey objects
*** Rebar protection, found at AIH, sometimes home depot but didn't see anything in May when I was looking
**rebar/screed stakes
**guy wire and findings

*metric handheld flow rod

===for camping===
* WATER
** water jug in nome storage
*Tents, sleeping bags, sleeping pads
** Tent is in room 112
** sleeping pads are in uaf storage
** sleeping bag are in uaf storage
* Stove
** propane stove in nome storage
*Food

Spring 2017 visit

2017-06-06T19:55:22Z

10.91.4.151: /* at toolik */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*<s>change notes in program where measure pressure to change CS100 to CS106
**remove sea level offset</s>
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??
*fix some of torn blue mesh panels on Wyoming shield

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet
*snow depth data
*go through enclosure in Brie's office
*figure out how to VPN into lognet
notes from 6/5/17
*screw in more secures for pluvio cable
*read about pluvio heater
*read about power for garden cam
*remove evap temp from program
*change program and wiring for HMPs
*change CNR4 heater?
*CMP6 heater?
*label all wires better
*move snow sensor away from tower?
*think about garden cam

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

Spring 2017 visit

2017-06-06T19:53:00Z

10.91.4.151: /* at toolik */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*<s>change notes in program where measure pressure to change CS100 to CS106
**remove sea level offset</s>
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??
*fix some of torn blue mesh panels on Wyoming shield

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet
*snow depth data
*go through enclosure in Brie's office
*figure out how to VPN into lognet
notes from 6/5/17
*screw in more secures for pluvio cable
*read about pluvio heater
*read about power for garden cam
*remove evap temp from program
*change program and wiring for HMPs
*change CNR4 heater?
*CMP6 heater?
*label all wires better
*move snow sensor away from tower?

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

Spring 2017 visit

2017-06-06T19:06:52Z

10.91.4.151: /* at toolik */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*<s>change notes in program where measure pressure to change CS100 to CS106
**remove sea level offset</s>
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??
*fix some of torn blue mesh panels on Wyoming shield

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet
*snow depth data
*go through enclosure in Brie's office
*figure out how to VPN into lognet
notes from 6/5/17
*screw in more secures for pluvio cable
*read about pluvio heater
*read about power for garden cam
*remove evap temp from program
*change program and wiring for HMPs
*change CNR4 heater?
*CMP6 heater?
*label all wires better

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

Spring 2017 visit

2017-06-06T05:35:32Z

10.91.4.151: /* at toolik */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*<s>change notes in program where measure pressure to change CS100 to CS106
**remove sea level offset</s>
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??
*fix some of torn blue mesh panels on Wyoming shield

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet
*snow depth data
*go through enclosure in Brie's office
*figure out how to VPN into lognet
notes from 6/5/17
*screw in more secures for pluvio cable
*read about pluvio heater
*read about power for garden cam
*remove evap temp from program
*change program and wiring for HMPs
*change CNR4 heater?
*CMP6 heater?

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

Spring 2017 visit

2017-06-06T05:31:34Z

10.91.4.151: /* at toolik */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*<s>change notes in program where measure pressure to change CS100 to CS106
**remove sea level offset</s>
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??
*fix some of torn blue mesh panels on Wyoming shield

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet
*snow depth data
*go through enclosure in Brie's office
*figure out how to VPN into lognet
notes from 6/5/17
*screw in more secures for pluvio cable
*read about pluvio heater
*read about power for garden cam
*remove evap temp from program
*change program and wiring for HMPs
*change CNR4 heater?

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

Spring 2017 visit

2017-06-06T05:29:46Z

10.91.4.151: /* at toolik */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*<s>change notes in program where measure pressure to change CS100 to CS106
**remove sea level offset</s>
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??
*fix some of torn blue mesh panels on Wyoming shield

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet
*snow depth data
*go through enclosure in Brie's office
*figure out how to VPN into lognet
notes from 6/5/17
*screw in more secures for pluvio cable
*read about pluvio heater
*read about power for garden cam
*remove evap temp from program
*change program and wiring for HMPs

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

Spring 2017 visit

2017-06-06T05:17:57Z

10.91.4.151: /* at toolik */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*<s>change notes in program where measure pressure to change CS100 to CS106
**remove sea level offset</s>
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??
*fix some of torn blue mesh panels on Wyoming shield

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet
*snow depth data
*go through enclosure in Brie's office
*figure out how to VPN into lognet
notes from 6/5/17
*screw in more secures for pluvio cable
*read about pluvio heater
*read about power for garden cam
*remove evap temp from program

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

Kougraok M64

2017-06-06T00:16:17Z

10.91.4.151: /* infrastructure */

Tape Color is '''Green'''

===In NGEE Container:===
* Tripod base with green tape. '''This is in NGEE Container'''
** Requires 1.25" schedule 40 pipe mast

===In UAF Storage===
* 1" x 3' aluminum pipe, three pieces
* 2 pipe wrenches
* large cable ties
* small cable ties
* fish tape
* 4 dog anchors
* saw
* grease
* anti oxidizing grease for electrical connections
* a bunch of hose clamps (including for precip bucket
* Bosch drill
* GIPL drill bit

===Sensors in UAF storage===
* Tipping bucket
* GIPL VATP

===To Buy in Nome===
* At Grizzly Hardware pick up a 1.25" schedule 40 pipe threaded on two sides

===To buy in Fairbanks===
* 1" topper for tripod past -Lily asks what is this? ''(These two items connect RM Young anemometer to the top of the tower)''
* 1" to 1.25" coupler to replace one used at teller top site -Lily asks if we still need this?

===Cross arm situation===
* Use short 1" Aluminum pipe for precip stand at site. Have three of these in the UAF Nome storage as well as the brackets required.
* the hose clamps for the site are in Nome along with some other items.
* Bob found 4 pcs 1" cross arms on 5/30 trip. There were also some 3/4" aluminum cross arms, perhaps for precip stand.
* 1 full altershield in Nome storage but... has flange plates on bottom so we'll need to do a bit more work to get things proper.
** (Flange Plate: http://www.homedepot.com/p/1-in-Black-Malleable-Iron-Threaded-Floor-Flange-521-605HN/100179931 )

===To ship from Fairbanks===
* 2 pcs 12V batteries

===Sensors===

{| class="wikitable"
|+Sensors
|-
|instrument
|SN
|where?
|height
|cable
|mount
|crossarm
|crossarm mount
|-
|HMP155A
|
|7pcs in UAF Storage
|1.5meters
|?
|yes and shield
|na
|na
|-
|RMyoung
|
|1 pcs in UAF Storage
|3meters
|?
|in box
|in box
|Frontier supply stocks them
|-
|Barometric pressure
|
|?
|na
|?
|na
|na
|na
|-
|CNR4
|
|in box
|
|in box
|in box
|
|
|-
|3 NDVI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|3 PRI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|Skin Temp
|
|in box
|
|attached
|in box
|
|
|-
|5 soil moisture
|
|in box
|color coded, see hydraprobe notes
|attached
|na
|na
|na
|-
|4 thermal conductivity
|
|only one in box
|
|
|
|
|
|-
|VAPT
|
| UAF Storage
|
|
|
|
|
|-
|SR50a?
|
| UAF Storage... I may have stolen the transducer though...
|
|need longer cable for far one
|
|
|
|-
|tipping bucket
|
|In Nome Storage
|
|
|?
|
|
|-

|}

Hydra Probe notes
* ID 0 = 5cm = red
* ID 1 = 10cm = orange
* ID 2 = 20cm = purple
* ID 3 = 30cm = brown
* ID 4 = 40cm = black

SRS notes
*PRI up = red tape = 7 SDI address
*PRI #1 = orange = 8 SDI address
*PRI #2 = purple = 9 SDI address
*NDVI up = red tape = A SDI address
*NDVI #1 = orange = B SDI address
*NDVI #2 = purple = C SDI address
Measure resistor value and SN beforehand?

===infrastructure===
*tower
**tripod - in storage
** mast- called Grizzly 907 443 2108 to see if we can reserve one
** alter shield for tipping bucket?
*power
**solar panel
**wires for panel
**charge controller
**crips/connectors for charge controller wires
**2 big batteries
**connector wires for batteries
**wire to logger
**fuse
*Enclosure
**mount for enclosure
**logger
**mux
**wires between mux and logger
**cable
**printed program
**screw driver
**CFM100+card
**grounding wire

===Actionpacker in uaf storage===
* Cable Ties
* 2 pipe wrenches
* hose clmaps
* three camping dinners (seafood deals)
* a bit more snacks
* fish tape
* soil samplers for teller bottom
* duct seal
* grease & anticorrosion goo
* (2) switched 12 volt control
* saw for dirt
* dog anchor
* box screw driver & serial cable (2)
* drill charger
* test radio for kougarok conenctions
** need a cigarette adapter
* hobo kit
* SR50A for K2 & K3
* 1" x 1" ubolt cross arm bracket
* 1" x 1.5" ubolt cross arm bracket
* 1" x 1" nurail cross
* 1" x 3/4" nurail cross
* LANL cameras
* bubble wrap
===General actionpacker placed into storage but may be useful for K64===
* Misc ubolts
* misc unistrut clamps (mostly wrong sizes I suspect)
* four pieces of unistrut 12-18 inches. two half size two full size
* three things of electrical tape, duct tape, rubber splicing tape
* couple NRS straps 9 & 12 feet
* 1 8GB CF card
* misc wire
* misc other
* baking soda

===Checklist for bob to find in Nome===
*Tripod kit -- Tripod is in NGEE conex
*trail mat for underneath tripod -- I'm not sure if we have any left
*Batteries for new K64 met tower -- The batteries are in room 112 in basement, or at least one, there are a couple others out there.
*tipping bucket
**hose clamps for mounting it
**cable (how long is it?)
*wind sensor
**cable
*1 SR50a sensor
**cable (how long is it?)
**mounting kit?
*Barometer
**cable
**what kind of screws do I need to mount it in the enclosure?
*VATP -- it is in Nome
**is there a resistor taped to it?
*HMP155
**cable
*sledge hammer
*shovel
*Drill for VATP
*Is Bob Bolton's sleeping bag there?
*if time: buy mast at Grizzly

Spring 2017 visit

2017-06-05T19:56:11Z

10.91.4.151: /* little activities */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*<s>change notes in program where measure pressure to change CS100 to CS106
**remove sea level offset</s>
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??
*fix some of torn blue mesh panels on Wyoming shield

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet
*snow depth data
*go through enclosure in Brie's office
*figure out how to VPN into lognet

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

Spring 2017 visit

2017-06-05T17:58:57Z

10.91.4.151: /* at toolik */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*<s>change notes in program where measure pressure to change CS100 to CS106 </s>
**remove sea level offset
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??
*fix some of torn blue mesh panels on Wyoming shield

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet
*snow depth data
*go through enclosure in Brie's office
*figure out how to VPN into lognet

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

Spring 2017 visit

2017-06-03T23:35:00Z

10.91.4.151: /* little activities */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*<s>change notes in program where measure pressure to change CS100 to CS106 </s>
**remove sea level offset
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??
*fix some of torn blue mesh panels on Wyoming shield

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet
*snow depth data
*go through enclosure in Brie's office

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

Spring 2017 visit

2017-06-03T19:24:55Z

10.91.4.151: /* little activities */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*change notes in program where measure pressure to change CS100 to CS106
**remove sea level offset
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??
*fix some of torn blue mesh panels on Wyoming shield

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet
*snow depth data
*go through enclosure in Brie's office

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

Spring 2017 visit

2017-06-03T18:31:04Z

10.91.4.151: /* at toolik */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*change notes in program where measure pressure to change CS100 to CS106
**remove sea level offset
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet
*snow depth data
*go through enclosure in Brie's office

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

Spring 2017 visit

2017-06-03T18:25:34Z

10.91.4.151: /* to bring */

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*change notes in program where measure pressure to change CS100 to CS106
**remove sea level offset
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt
*teflon tape, super large crescent wrench for the Evap pan. BUT toolik does have these things

Spring 2017 visit

2017-06-03T17:07:47Z

10.91.4.151:

===CNR4===
* Check out the status of the heater wiring for CNR4
** is it even wired? to which ports?
** change the program notes if wired
** change program controls for heater
** bring up couple SW12V
*change desiccant in CNR4

===bf5 sunshine sensor===
*install BF5 sensor
** tripod is 9ft7in from tower. cable is 5m. so this ''should'' work out
**bring some spare AC power line, inverters and plugs to set up power for heater.

===organize the enclosure===
**zip ties of many colors and sizes
**wires of many colors (mostly red and black)
**white wire connector things

===evap pan===
*float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the
gauge.
*field calibrate

Fill pan partway with water, measure height with ruler in mm
Measure voltage by reading the EvapLevelTemp variable on the program
Add more water, measure water depth in pan
Measure voltage
Calculate multiplier and offset using y = mx+b
m(multiplier) = (height1-height2)/(voltage2-voltage1)
b(offset) = height1-(m*voltage1)

===little activities===
*add terrestrial quantum to sensor wiring notes at top of program
*check what the calconnector looks like for lake PAR.
**maybe need to buy a second one so can coordinate with calibration swaps
**its reading negative because the sensor head was swapped wrong, but this isn't an issue.
*change notes in program where measure pressure to change CS100 to CS106
**remove sea level offset
*get serial number for radios
*get height of terrestrial PAR
*check if pluvio is pointing north
*think about soil temps- at least find them
*clean all rad sensor domes with cloth
*level all rad sensors
*Garden cam??

===Lake things===
*probs can't do this trip
*stabilize underwater par sensor with second string for cleaning

===at toolik===
*go through all metadata - remember the comments column
*think about PAR sensors
*upgrade loggernet

===to bring===
*tools http://ngeedata.iarc.uaf.edu/wiki/Tool_list
*computer + charger
*field laptop + charger
*fish tape
*BF5 sensor + mount+ cable +cable conduit+ electrical accessories
*CNR4 heater+ cable
**2 x SW12V BORROWED FROM NGEE, MUST REPLACE IF I USE IT
*field book
*copy of wiki

Clothes
*raincoat
*rain pants
*sourdough jacket
*warm hats
*gloves and mittens
*blue muck boots
*winter hiking boots
*fleece pants
*leggings
*orange fleece
*wool long sleeve
*socks, undies
*work pants

Other Gear
*-10 sleeping bag and stuff sack
*sleeping pad
*beverages
*earplugs

SHOULD HAVE HAD
*bug shirt