http://ocotal.iarc.uaf.edu/api.php?action=feedcontributions&feedformat=atom&user=137.229.29.72&*IARC 207 Wiki - User contributions [en]2026-05-13T02:22:37ZUser contributionsMediaWiki 1.34.2http://ocotal.iarc.uaf.edu/index.php?title=May_31-_June_6th,_2015_site_visit&diff=2286May 31- June 6th, 2015 site visit2015-05-30T18:45:35Z<p>137.229.29.72: /* Items to bring up */</p>
<hr />
<div>== Instal evap pan ==<br />
*field calibrate<br />
*edit program<br />
*for platform<br />
**exterior grade plywood - home depot will cut it<br />
**exterior deck screws<br />
*calibrate in mm to get units in mm<br />
<br />
== Wind sensors replacement ==<br />
*calculate multiplier for wind direction sensor. for back calculation purposes<br />
*Replace wind direction sensors<br />
*align (declination: 18.5 degrees)<br />
** North (0/360 degrees) when nose points AWAY from box, for both sensors<br />
**<s>aligned in office so that when nose faces same way as box, reads 180.</s><br />
*to install propeller, hand tighten then tighten with channel locks<br />
*both wind sensors can use same excitation port<br />
*White = 5106, Black = 5103<br />
<br />
== Telemetry ==<br />
Finish installing radio + ethernet for redundancy<br />
*old RF310B is in WQ in computer racks to left after enter<br />
**black box with campbell scientific marking<br />
**put timer on power source<br />
*radio connected to CR3000 with CS10 port gets power from this port as well<br />
*check config settings on NL201 nl201.toolik.uaf.edu should be: <br />
**HwAddr: 00:D0:2C:02:0D:73.<br />
**IP address: 137.229.91.81<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
*for NL100 I'm bring up<br />
**HwAddr (MAC address): 00d02c0004c0 <br />
**IP address: 137.229.91.82<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
<br />
== Items to bring up ==<br />
*alcohol swabs<br />
*compass <br />
*outlet timer for old radio<br />
*NL100<br />
*smart phone<br />
*evap gauge <br />
*two RM young wind sensors<br />
*sleeping bag<br />
*nut driver for tower base<br />
*drill + charger<br />
*tube for leveling platform<br />
*wood and screws for platform<br />
*zip ties<br />
*null modem cable for NL100 communication<br />
*cat5 cable and tools for creating connectors<br />
*wire to power NL100 from CR3000 AND ac adapter if outlet space<br />
*field laptop + charger<br />
*laptop + charger<br />
*plywood boards<br />
*field notebook<br />
*camera<br />
*tool bag<br />
*fish tape<br />
*electrical tape<br />
*ethernet-usb plug<br />
*serial-usb plug<br />
*rag<br />
*cable housing<br />
*pertinent manuals<br />
*extension chord<br />
*disc<br />
<br />
== Items to purchase ==<br />
*alcohol swabs<br />
*power strip<br />
*compass<br />
*32 AA batteries for GardenCam<br />
*plywood +screws for base<br />
<br />
== Tipping tower ==<br />
*grab 2 saw horses<br />
*undo one guy wire, loosen others<br />
*undo one leg bolts, loosen others<br />
** 2 bolts on each leg, take off both on one leg, just loosen bottom screw for other 2 legs<br />
*CAREFUL of sensor wires when lowering tower<br />
*have WD40 with me in case can't get wind sensor screws undone<br />
<br />
when raise tower, make turnbuckles taught but not too tight<br />
<br />
== PLAN ==<br />
<br />
===Telemetry===<br />
* plug in timer to old radio base<br />
* check config settings on NL201 in CPS shed<br />
* run cat5 line from radio in CPS shed<br />
* leave NL100 in enclosure, wire power from data logger or outlet<br />
*(grab ladder against back of tool shed to look into box)<br />
<br />
===Wind Sensors + Garden Cam===<br />
*Alignment <br />
**which way does tower tip and how is crossbar oriented <br />
**stake out east west <br />
* Tip Tower<br />
* Reset Garden Cam<br />
**remover flash drive (may need to cut tape for this)<br />
**download pics<br />
**clear drive<br />
*Replace Wind sensors<br />
**use old mounts or change if necessary<br />
**screw on propeller, hand tighten then tighten with channel locks <br />
**alignment ring then sensor <br />
* zip tie wires and pull them into box<br />
* Wire Sensors<br />
' RM Young 5103 Wind Monitor (black)<br />
<br />
' Red Wire -- CR3000 P1<br />
<br />
' Green Wire -- CR3000 SE1<br />
<br />
' Blue Wire -- CR3000 VX1<br />
<br />
' Clear Wire -- CR3000 AG<br />
<br />
' Black Wire -- CR3000 AG<br />
<br />
' White Wire -- CR3000 AG<br />
<br />
' RM Young 5106 Wind Monitor(white)<br />
<br />
' Red Wire -- CR3000 P2<br />
<br />
' Green Wire -- CR3000 SE2<br />
<br />
' Blue Wire -- CR3000 VX1<br />
<br />
' Clear Wire -- CR3000 AG<br />
<br />
' Black Wire -- CR3000 AG<br />
<br />
' White Wire -- CR3000 AG<br />
<br />
* Download data files from CR3000<br />
* upload new program<br />
* Align Wind sensors on ground as best as possible<br />
** first horizontal plane<br />
** second east-west<br />
* Raise tower<br />
** have Brie climb it to align sensors if necessary<br />
* Replace batteries in Garden Cam power case<br />
<br />
===Evaporation Gauge===<br />
*Build platform with pallets and plywood<br />
*attach gauge to pan with pipe<br />
*run wire through housing and into enclosure<br />
**' Evaporation Pan<br />
**' White Wire -- CR3000 SE16<br />
**' Red Wire -- CR3000 VX3 <br />
**' Black Wire -- CR3000 Signal Ground<br />
*Calibrate<br />
** Fill pan partway with water, measure height with ruler in mm<br />
** Measure voltage by reading the EvapLevelTemp variable on the program<br />
** Add more water, measure water depth in pan<br />
** Measure voltage<br />
** Calculate multiplier and offset using y = mx+b<br />
***m(multiplier) = (height1-height2)/(voltage2-voltage1)<br />
***b(offset) = height1-(m*voltage1)<br />
*Change multiplier and offset in program<br />
**download data<br />
**upload new program<br />
<br />
<br />
=== Additional tasks ===<br />
(grab ladder against back of tool shed to look into box)<br />
<br />
*download CR3000 + radio device config settings<br />
*level and alcohol swab radiometer (par) <br />
*level and alcohol swab 3 radiometers on old tower (net Rad, UVA, UVB)<br />
<br />
*Pluvio<br />
**Hole in mesh to craw in, 3 captive screws holding on outer shield<br />
**empty most of water inside plastic inner tub<br />
**remove any dead animals <br />
<br />
*note any damage<br />
*Make sure no water in battery box<br />
*inspect seals where wires go in<br />
*inspect solar panels<br />
<br />
== TODO ==<br />
*<s>TELEMETRY<s><br />
*<s>PR and purchase stuff</s><br />
*<s>update program for evap pan, wind sensors, snow depth quality number</s><br />
*<s>program NL100</s><br />
*<s>evap gauge base supplies and logistics</s><br />
*<s>learn ethernet cable connectors</s><br />
*<s>GardenCam (how reset? what does PI want?)</s><br />
*<s>figure out where wind sensor go on data logger, and how to mount</s><br />
*<s>re-align wind sensor from basement</s><br />
*read pluvio manual<br />
*<s>find photo of evap pan base</s><br />
*<s>ask toolik for pallets</s><br />
*<s>new longer cable for wind sensor</s><br />
*<s>instal skype on iphone</s><br />
*<s>get wind sensor mounting pole from basement</s><br />
*<s>check types of wind instruments</s><br />
*<s>write out plan</s><br />
*pack<br />
*<s>check how long cable on evap gauge is</s></div>137.229.29.72http://ocotal.iarc.uaf.edu/index.php?title=May_31-_June_6th,_2015_site_visit&diff=2285May 31- June 6th, 2015 site visit2015-05-30T06:10:07Z<p>137.229.29.72: /* TODO */</p>
<hr />
<div>== Instal evap pan ==<br />
*field calibrate<br />
*edit program<br />
*for platform<br />
**exterior grade plywood - home depot will cut it<br />
**exterior deck screws<br />
*calibrate in mm to get units in mm<br />
<br />
== Wind sensors replacement ==<br />
*calculate multiplier for wind direction sensor. for back calculation purposes<br />
*Replace wind direction sensors<br />
*align (declination: 18.5 degrees)<br />
** North (0/360 degrees) when nose points AWAY from box, for both sensors<br />
**<s>aligned in office so that when nose faces same way as box, reads 180.</s><br />
*to install propeller, hand tighten then tighten with channel locks<br />
*both wind sensors can use same excitation port<br />
*White = 5106, Black = 5103<br />
<br />
== Telemetry ==<br />
Finish installing radio + ethernet for redundancy<br />
*old RF310B is in WQ in computer racks to left after enter<br />
**black box with campbell scientific marking<br />
**put timer on power source<br />
*radio connected to CR3000 with CS10 port gets power from this port as well<br />
*check config settings on NL201 nl201.toolik.uaf.edu should be: <br />
**HwAddr: 00:D0:2C:02:0D:73.<br />
**IP address: 137.229.91.81<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
*for NL100 I'm bring up<br />
**HwAddr (MAC address): 00d02c0004c0 <br />
**IP address: 137.229.91.82<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
<br />
== Items to bring up ==<br />
*alcohol swabs<br />
*compass <br />
*outlet timer for old radio<br />
*NL100<br />
*smart phone<br />
*evap gauge <br />
*two RM young wind sensors<br />
*sleeping bag<br />
*nut driver for tower base<br />
*drill + charger<br />
*tube for leveling platform<br />
*wood and screws for platform<br />
*zip ties<br />
*null modem cable for NL100 communication<br />
*cat5 cable and tools for creating connectors<br />
*wire to power NL100 from CR3000 AND ac adapter if outlet space<br />
*field laptop + charger<br />
*laptop + charger<br />
*plywood boards<br />
*field notebook<br />
*camera<br />
*tool bag<br />
*fish tape<br />
*electrical tape<br />
*ethernet-usb plug<br />
*serial-usb plug<br />
<br />
== Items to purchase ==<br />
*alcohol swabs<br />
*power strip<br />
*compass<br />
*32 AA batteries for GardenCam<br />
*plywood +screws for base<br />
<br />
== Tipping tower ==<br />
*grab 2 saw horses<br />
*undo one guy wire, loosen others<br />
*undo one leg bolts, loosen others<br />
** 2 bolts on each leg, take off both on one leg, just loosen bottom screw for other 2 legs<br />
*CAREFUL of sensor wires when lowering tower<br />
*have WD40 with me in case can't get wind sensor screws undone<br />
<br />
when raise tower, make turnbuckles taught but not too tight<br />
<br />
== PLAN ==<br />
<br />
===Telemetry===<br />
* plug in timer to old radio base<br />
* check config settings on NL201 in CPS shed<br />
* run cat5 line from radio in CPS shed<br />
* leave NL100 in enclosure, wire power from data logger or outlet<br />
*(grab ladder against back of tool shed to look into box)<br />
<br />
===Wind Sensors + Garden Cam===<br />
*Alignment <br />
**which way does tower tip and how is crossbar oriented <br />
**stake out east west <br />
* Tip Tower<br />
* Reset Garden Cam<br />
**remover flash drive (may need to cut tape for this)<br />
**download pics<br />
**clear drive<br />
*Replace Wind sensors<br />
**use old mounts or change if necessary<br />
**screw on propeller, hand tighten then tighten with channel locks <br />
**alignment ring then sensor <br />
* zip tie wires and pull them into box<br />
* Wire Sensors<br />
' RM Young 5103 Wind Monitor (black)<br />
<br />
' Red Wire -- CR3000 P1<br />
<br />
' Green Wire -- CR3000 SE1<br />
<br />
' Blue Wire -- CR3000 VX1<br />
<br />
' Clear Wire -- CR3000 AG<br />
<br />
' Black Wire -- CR3000 AG<br />
<br />
' White Wire -- CR3000 AG<br />
<br />
' RM Young 5106 Wind Monitor(white)<br />
<br />
' Red Wire -- CR3000 P2<br />
<br />
' Green Wire -- CR3000 SE2<br />
<br />
' Blue Wire -- CR3000 VX1<br />
<br />
' Clear Wire -- CR3000 AG<br />
<br />
' Black Wire -- CR3000 AG<br />
<br />
' White Wire -- CR3000 AG<br />
<br />
* Download data files from CR3000<br />
* upload new program<br />
* Align Wind sensors on ground as best as possible<br />
** first horizontal plane<br />
** second east-west<br />
* Raise tower<br />
** have Brie climb it to align sensors if necessary<br />
* Replace batteries in Garden Cam power case<br />
<br />
===Evaporation Gauge===<br />
*Build platform with pallets and plywood<br />
*attach gauge to pan with pipe<br />
*run wire through housing and into enclosure<br />
**' Evaporation Pan<br />
**' White Wire -- CR3000 SE16<br />
**' Red Wire -- CR3000 VX3 <br />
**' Black Wire -- CR3000 Signal Ground<br />
*Calibrate<br />
** Fill pan partway with water, measure height with ruler in mm<br />
** Measure voltage by reading the EvapLevelTemp variable on the program<br />
** Add more water, measure water depth in pan<br />
** Measure voltage<br />
** Calculate multiplier and offset using y = mx+b<br />
***m(multiplier) = (height1-height2)/(voltage2-voltage1)<br />
***b(offset) = height1-(m*voltage1)<br />
*Change multiplier and offset in program<br />
**download data<br />
**upload new program<br />
<br />
<br />
=== Additional tasks ===<br />
(grab ladder against back of tool shed to look into box)<br />
<br />
*download CR3000 + radio device config settings<br />
*level and alcohol swab radiometer (par) <br />
*level and alcohol swab 3 radiometers on old tower (net Rad, UVA, UVB)<br />
<br />
*Pluvio<br />
**Hole in mesh to craw in, 3 captive screws holding on outer shield<br />
**empty most of water inside plastic inner tub<br />
**remove any dead animals <br />
<br />
*note any damage<br />
*Make sure no water in battery box<br />
*inspect seals where wires go in<br />
*inspect solar panels<br />
<br />
== TODO ==<br />
*<s>TELEMETRY<s><br />
*<s>PR and purchase stuff</s><br />
*<s>update program for evap pan, wind sensors, snow depth quality number</s><br />
*<s>program NL100</s><br />
*<s>evap gauge base supplies and logistics</s><br />
*<s>learn ethernet cable connectors</s><br />
*<s>GardenCam (how reset? what does PI want?)</s><br />
*<s>figure out where wind sensor go on data logger, and how to mount</s><br />
*<s>re-align wind sensor from basement</s><br />
*read pluvio manual<br />
*<s>find photo of evap pan base</s><br />
*<s>ask toolik for pallets</s><br />
*<s>new longer cable for wind sensor</s><br />
*<s>instal skype on iphone</s><br />
*<s>get wind sensor mounting pole from basement</s><br />
*<s>check types of wind instruments</s><br />
*<s>write out plan</s><br />
*pack<br />
*<s>check how long cable on evap gauge is</s></div>137.229.29.72http://ocotal.iarc.uaf.edu/index.php?title=May_31-_June_6th,_2015_site_visit&diff=2284May 31- June 6th, 2015 site visit2015-05-30T06:02:46Z<p>137.229.29.72: /* PLAN */</p>
<hr />
<div>== Instal evap pan ==<br />
*field calibrate<br />
*edit program<br />
*for platform<br />
**exterior grade plywood - home depot will cut it<br />
**exterior deck screws<br />
*calibrate in mm to get units in mm<br />
<br />
== Wind sensors replacement ==<br />
*calculate multiplier for wind direction sensor. for back calculation purposes<br />
*Replace wind direction sensors<br />
*align (declination: 18.5 degrees)<br />
** North (0/360 degrees) when nose points AWAY from box, for both sensors<br />
**<s>aligned in office so that when nose faces same way as box, reads 180.</s><br />
*to install propeller, hand tighten then tighten with channel locks<br />
*both wind sensors can use same excitation port<br />
*White = 5106, Black = 5103<br />
<br />
== Telemetry ==<br />
Finish installing radio + ethernet for redundancy<br />
*old RF310B is in WQ in computer racks to left after enter<br />
**black box with campbell scientific marking<br />
**put timer on power source<br />
*radio connected to CR3000 with CS10 port gets power from this port as well<br />
*check config settings on NL201 nl201.toolik.uaf.edu should be: <br />
**HwAddr: 00:D0:2C:02:0D:73.<br />
**IP address: 137.229.91.81<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
*for NL100 I'm bring up<br />
**HwAddr (MAC address): 00d02c0004c0 <br />
**IP address: 137.229.91.82<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
<br />
== Items to bring up ==<br />
*alcohol swabs<br />
*compass <br />
*outlet timer for old radio<br />
*NL100<br />
*smart phone<br />
*evap gauge <br />
*two RM young wind sensors<br />
*sleeping bag<br />
*nut driver for tower base<br />
*drill + charger<br />
*tube for leveling platform<br />
*wood and screws for platform<br />
*zip ties<br />
*null modem cable for NL100 communication<br />
*cat5 cable and tools for creating connectors<br />
*wire to power NL100 from CR3000 AND ac adapter if outlet space<br />
*field laptop + charger<br />
*laptop + charger<br />
*plywood boards<br />
*field notebook<br />
*camera<br />
*tool bag<br />
*fish tape<br />
*electrical tape<br />
*ethernet-usb plug<br />
*serial-usb plug<br />
<br />
== Items to purchase ==<br />
*alcohol swabs<br />
*power strip<br />
*compass<br />
*32 AA batteries for GardenCam<br />
*plywood +screws for base<br />
<br />
== Tipping tower ==<br />
*grab 2 saw horses<br />
*undo one guy wire, loosen others<br />
*undo one leg bolts, loosen others<br />
** 2 bolts on each leg, take off both on one leg, just loosen bottom screw for other 2 legs<br />
*CAREFUL of sensor wires when lowering tower<br />
*have WD40 with me in case can't get wind sensor screws undone<br />
<br />
when raise tower, make turnbuckles taught but not too tight<br />
<br />
== PLAN ==<br />
<br />
===Telemetry===<br />
* plug in timer to old radio base<br />
* check config settings on NL201 in CPS shed<br />
* run cat5 line from radio in CPS shed<br />
* leave NL100 in enclosure, wire power from data logger or outlet<br />
*(grab ladder against back of tool shed to look into box)<br />
<br />
===Wind Sensors + Garden Cam===<br />
*Alignment <br />
**which way does tower tip and how is crossbar oriented <br />
**stake out east west <br />
* Tip Tower<br />
* Reset Garden Cam<br />
**remover flash drive (may need to cut tape for this)<br />
**download pics<br />
**clear drive<br />
*Replace Wind sensors<br />
**use old mounts or change if necessary<br />
**screw on propeller, hand tighten then tighten with channel locks <br />
**alignment ring then sensor <br />
* zip tie wires and pull them into box<br />
* Wire Sensors<br />
' RM Young 5103 Wind Monitor (black)<br />
<br />
' Red Wire -- CR3000 P1<br />
<br />
' Green Wire -- CR3000 SE1<br />
<br />
' Blue Wire -- CR3000 VX1<br />
<br />
' Clear Wire -- CR3000 AG<br />
<br />
' Black Wire -- CR3000 AG<br />
<br />
' White Wire -- CR3000 AG<br />
<br />
' RM Young 5106 Wind Monitor(white)<br />
<br />
' Red Wire -- CR3000 P2<br />
<br />
' Green Wire -- CR3000 SE2<br />
<br />
' Blue Wire -- CR3000 VX1<br />
<br />
' Clear Wire -- CR3000 AG<br />
<br />
' Black Wire -- CR3000 AG<br />
<br />
' White Wire -- CR3000 AG<br />
<br />
* Download data files from CR3000<br />
* upload new program<br />
* Align Wind sensors on ground as best as possible<br />
** first horizontal plane<br />
** second east-west<br />
* Raise tower<br />
** have Brie climb it to align sensors if necessary<br />
* Replace batteries in Garden Cam power case<br />
<br />
===Evaporation Gauge===<br />
*Build platform with pallets and plywood<br />
*attach gauge to pan with pipe<br />
*run wire through housing and into enclosure<br />
**' Evaporation Pan<br />
**' White Wire -- CR3000 SE16<br />
**' Red Wire -- CR3000 VX3 <br />
**' Black Wire -- CR3000 Signal Ground<br />
*Calibrate<br />
** Fill pan partway with water, measure height with ruler in mm<br />
** Measure voltage by reading the EvapLevelTemp variable on the program<br />
** Add more water, measure water depth in pan<br />
** Measure voltage<br />
** Calculate multiplier and offset using y = mx+b<br />
***m(multiplier) = (height1-height2)/(voltage2-voltage1)<br />
***b(offset) = height1-(m*voltage1)<br />
*Change multiplier and offset in program<br />
**download data<br />
**upload new program<br />
<br />
<br />
=== Additional tasks ===<br />
(grab ladder against back of tool shed to look into box)<br />
<br />
*download CR3000 + radio device config settings<br />
*level and alcohol swab radiometer (par) <br />
*level and alcohol swab 3 radiometers on old tower (net Rad, UVA, UVB)<br />
<br />
*Pluvio<br />
**Hole in mesh to craw in, 3 captive screws holding on outer shield<br />
**empty most of water inside plastic inner tub<br />
**remove any dead animals <br />
<br />
*note any damage<br />
*Make sure no water in battery box<br />
*inspect seals where wires go in<br />
*inspect solar panels<br />
<br />
== TODO ==<br />
*<s>TELEMETRY<s><br />
*<s>PR and purchase stuff</s><br />
*<s>update program for evap pan, wind sensors, snow depth quality number</s><br />
*<s>program NL100</s><br />
*<s>evap gauge base supplies and logistics</s><br />
*<s>learn ethernet cable connectors</s><br />
*GardenCam (how reset? what does PI want?)<br />
*<s>figure out where wind sensor go on data logger, and how to mount</s><br />
*<s>re-align wind sensor from basement</s><br />
*read pluvio manual<br />
*<s>find photo of evap pan base</s><br />
*<s>ask toolik for pallets</s><br />
*<s>new longer cable for wind sensor</s><br />
*<s>instal skype on iphone</s><br />
*<s>get wind sensor mounting pole from basement</s><br />
*<s>check types of wind instruments</s><br />
*write out plan<br />
*pack<br />
*<s>check how long cable on evap gauge is</s></div>137.229.29.72http://ocotal.iarc.uaf.edu/index.php?title=May_31-_June_6th,_2015_site_visit&diff=2283May 31- June 6th, 2015 site visit2015-05-30T05:57:24Z<p>137.229.29.72: </p>
<hr />
<div>== Instal evap pan ==<br />
*field calibrate<br />
*edit program<br />
*for platform<br />
**exterior grade plywood - home depot will cut it<br />
**exterior deck screws<br />
*calibrate in mm to get units in mm<br />
<br />
== Wind sensors replacement ==<br />
*calculate multiplier for wind direction sensor. for back calculation purposes<br />
*Replace wind direction sensors<br />
*align (declination: 18.5 degrees)<br />
** North (0/360 degrees) when nose points AWAY from box, for both sensors<br />
**<s>aligned in office so that when nose faces same way as box, reads 180.</s><br />
*to install propeller, hand tighten then tighten with channel locks<br />
*both wind sensors can use same excitation port<br />
*White = 5106, Black = 5103<br />
<br />
== Telemetry ==<br />
Finish installing radio + ethernet for redundancy<br />
*old RF310B is in WQ in computer racks to left after enter<br />
**black box with campbell scientific marking<br />
**put timer on power source<br />
*radio connected to CR3000 with CS10 port gets power from this port as well<br />
*check config settings on NL201 nl201.toolik.uaf.edu should be: <br />
**HwAddr: 00:D0:2C:02:0D:73.<br />
**IP address: 137.229.91.81<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
*for NL100 I'm bring up<br />
**HwAddr (MAC address): 00d02c0004c0 <br />
**IP address: 137.229.91.82<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
<br />
== Items to bring up ==<br />
*alcohol swabs<br />
*compass <br />
*outlet timer for old radio<br />
*NL100<br />
*smart phone<br />
*evap gauge <br />
*two RM young wind sensors<br />
*sleeping bag<br />
*nut driver for tower base<br />
*drill + charger<br />
*tube for leveling platform<br />
*wood and screws for platform<br />
*zip ties<br />
*null modem cable for NL100 communication<br />
*cat5 cable and tools for creating connectors<br />
*wire to power NL100 from CR3000 AND ac adapter if outlet space<br />
*field laptop + charger<br />
*laptop + charger<br />
*plywood boards<br />
*field notebook<br />
*camera<br />
*tool bag<br />
*fish tape<br />
*electrical tape<br />
*ethernet-usb plug<br />
*serial-usb plug<br />
<br />
== Items to purchase ==<br />
*alcohol swabs<br />
*power strip<br />
*compass<br />
*32 AA batteries for GardenCam<br />
*plywood +screws for base<br />
<br />
== Tipping tower ==<br />
*grab 2 saw horses<br />
*undo one guy wire, loosen others<br />
*undo one leg bolts, loosen others<br />
** 2 bolts on each leg, take off both on one leg, just loosen bottom screw for other 2 legs<br />
*CAREFUL of sensor wires when lowering tower<br />
*have WD40 with me in case can't get wind sensor screws undone<br />
<br />
when raise tower, make turnbuckles taught but not too tight<br />
<br />
== PLAN ==<br />
<br />
===Telemetry===<br />
* plug in timer to old radio base<br />
* check config settings on NL201 in CPS shed<br />
* run cat5 line from radio in CPS shed<br />
* leave NL100 in enclosure, wire power from data logger or outlet<br />
*(grab ladder against back of tool shed to look into box)<br />
<br />
===Wind Sensors + Garden Cam===<br />
*Alignment <br />
**which way does tower tip and how is crossbar oriented <br />
**stake out east west <br />
* Tip Tower<br />
* Reset Garden Cam<br />
**remover flash drive (may need to cut tape for this)<br />
**download pics<br />
**clear drive<br />
*Replace Wind sensors<br />
**use old mounts or change if necessary<br />
**screw on propeller, hand tighten then tighten with channel locks <br />
**alignment ring then sensor <br />
* zip tie wires and pull them into box<br />
* Wire Sensors<br />
' RM Young 5103 Wind Monitor (black)<br />
<br />
' Red Wire -- CR3000 P1<br />
<br />
' Green Wire -- CR3000 SE1<br />
<br />
' Blue Wire -- CR3000 VX1<br />
<br />
' Clear Wire -- CR3000 AG<br />
<br />
' Black Wire -- CR3000 AG<br />
<br />
' White Wire -- CR3000 AG<br />
<br />
' RM Young 5106 Wind Monitor(white)<br />
<br />
' Red Wire -- CR3000 P2<br />
<br />
' Green Wire -- CR3000 SE2<br />
<br />
' Blue Wire -- CR3000 VX1<br />
<br />
' Clear Wire -- CR3000 AG<br />
<br />
' Black Wire -- CR3000 AG<br />
<br />
' White Wire -- CR3000 AG<br />
<br />
* Download data files from CR3000<br />
* upload new program<br />
* Align Wind sensors on ground as best as possible<br />
** first horizontal plane<br />
** second east-west<br />
* Raise tower<br />
** have Brie climb it to align sensors if necessary<br />
* Replace batteries in Garden Cam power case<br />
<br />
Evaporation Gauge<br />
*Build platform with pallets and plywood<br />
*attach gauge to pan with pipe<br />
*run wire through housing and into enclosure<br />
**' Evaporation Pan<br />
**' White Wire -- CR3000 SE16<br />
**' Red Wire -- CR3000 VX3 <br />
**' Black Wire -- CR3000 Signal Ground<br />
*Calibrate<br />
** Fill pan partway with water, measure height with ruler in mm<br />
** Measure voltage by reading the EvapLevelTemp variable on the program<br />
** Add more water, measure water depth in pan<br />
** Measure voltage<br />
** Calculate multiplier and offset using y = mx+b<br />
***m(multiplier) = (height1-height2)/(voltage2-voltage1)<br />
***b(offset) = height1-(m*voltage1)<br />
*Change multiplier and offset in program<br />
**download data<br />
**upload new program<br />
<br />
<br />
=== Additional tasks ===<br />
(grab ladder against back of tool shed to look into box)<br />
<br />
*download CR3000 + radio device config settings<br />
*level and alcohol swab radiometer (par) <br />
*level and alcohol swab 3 radiometers on old tower (net Rad, UVA, UVB)<br />
<br />
*Pluvio<br />
**Hole in mesh to craw in, 3 captive screws holding on outer shield<br />
**empty most of water inside plastic inner tub<br />
**remove any dead animals <br />
<br />
*note any damage<br />
*Make sure no water in battery box<br />
*inspect seals where wires go in<br />
*inspect solar panels<br />
<br />
== TODO ==<br />
*<s>TELEMETRY<s><br />
*<s>PR and purchase stuff</s><br />
*<s>update program for evap pan, wind sensors, snow depth quality number</s><br />
*<s>program NL100</s><br />
*<s>evap gauge base supplies and logistics</s><br />
*<s>learn ethernet cable connectors</s><br />
*GardenCam (how reset? what does PI want?)<br />
*<s>figure out where wind sensor go on data logger, and how to mount</s><br />
*<s>re-align wind sensor from basement</s><br />
*read pluvio manual<br />
*<s>find photo of evap pan base</s><br />
*<s>ask toolik for pallets</s><br />
*<s>new longer cable for wind sensor</s><br />
*<s>instal skype on iphone</s><br />
*<s>get wind sensor mounting pole from basement</s><br />
*<s>check types of wind instruments</s><br />
*write out plan<br />
*pack<br />
*<s>check how long cable on evap gauge is</s></div>137.229.29.72http://ocotal.iarc.uaf.edu/index.php?title=May_31-_June_6th,_2015_site_visit&diff=2282May 31- June 6th, 2015 site visit2015-05-30T05:54:05Z<p>137.229.29.72: </p>
<hr />
<div>== Instal evap pan ==<br />
*field calibrate<br />
*edit program<br />
*for platform<br />
**exterior grade plywood - home depot will cut it<br />
**exterior deck screws<br />
*calibrate in mm to get units in mm<br />
<br />
== Wind sensors replacement ==<br />
*calculate multiplier for wind direction sensor. for back calculation purposes<br />
*Replace wind direction sensors<br />
*align (declination: 18.5 degrees)<br />
** North (0/360 degrees) when nose points AWAY from box, for both sensors<br />
**aligned in office so that when nose faces same way as box, reads 180.<br />
*to install propeller, hand tighten then tighten with channel locks<br />
*both wind sensors can use same excitation port<br />
*White = 5106, Black = 5103<br />
<br />
== Telemetry ==<br />
Finish installing radio + ethernet for redundancy<br />
*old RF310B is in WQ in computer racks to left after enter<br />
**black box with campbell scientific marking<br />
**put timer on power source<br />
*radio connected to CR3000 with CS10 port gets power from this port as well<br />
*check config settings on NL201 nl201.toolik.uaf.edu should be: <br />
**HwAddr: 00:D0:2C:02:0D:73.<br />
**IP address: 137.229.91.81<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
*for NL100 I'm bring up<br />
**HwAddr (MAC address): 00d02c0004c0 <br />
**IP address: 137.229.91.82<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
<br />
== Items to bring up ==<br />
*alcohol swabs<br />
*compass <br />
*outlet timer for old radio<br />
*NL100<br />
*smart phone<br />
*evap gauge <br />
*two RM young wind sensors<br />
*sleeping bag<br />
*nut driver for tower base<br />
*drill + charger<br />
*tube for leveling platform<br />
*wood and screws for platform<br />
*zip ties<br />
*null modem cable for NL100 communication<br />
*cat5 cable and tools for creating connectors<br />
*wire to power NL100 from CR3000 AND ac adapter if outlet space<br />
*field laptop + charger<br />
*laptop + charger<br />
*plywood boards<br />
*field notebook<br />
*camera<br />
*tool bag<br />
*fish tape<br />
*electrical tape<br />
*ethernet-usb plug<br />
*serial-usb plug<br />
<br />
== Items to purchase ==<br />
*alcohol swabs<br />
*power strip<br />
*compass<br />
*32 AA batteries for GardenCam<br />
*plywood +screws for base<br />
<br />
== Tipping tower ==<br />
*grab 2 saw horses<br />
*undo one guy wire, loosen others<br />
*undo one leg bolts, loosen others<br />
** 2 bolts on each leg, take off both on one leg, just loosen bottom screw for other 2 legs<br />
*CAREFUL of sensor wires when lowering tower<br />
*have WD40 with me in case can't get wind sensor screws undone<br />
<br />
when raise tower, make turnbuckles taught but not too tight<br />
<br />
== PLAN ==<br />
<br />
===Telemetry===<br />
* plug in timer to old radio base<br />
* check config settings on NL201 in CPS shed<br />
* run cat5 line from radio in CPS shed<br />
* leave NL100 in enclosure, wire power from data logger or outlet<br />
*(grab ladder against back of tool shed to look into box)<br />
<br />
===Wind Sensors + Garden Cam===<br />
*Alignment <br />
**which way does tower tip and how is crossbar oriented <br />
**stake out east west <br />
* Tip Tower<br />
* Reset Garden Cam<br />
**remover flash drive (may need to cut tape for this)<br />
**download pics<br />
**clear drive<br />
*Replace Wind sensors<br />
**use old mounts or change if necessary<br />
**screw on propeller <br />
**alignment ring then sensor <br />
* zip tie wires and pull them into box<br />
* Wire Sensors<br />
' RM Young 5103 Wind Monitor (black)<br />
<br />
' Red Wire -- CR3000 P1<br />
<br />
' Green Wire -- CR3000 SE1<br />
<br />
' Blue Wire -- CR3000 VX1<br />
<br />
' Clear Wire -- CR3000 AG<br />
<br />
' Black Wire -- CR3000 AG<br />
<br />
' White Wire -- CR3000 AG<br />
<br />
' RM Young 5106 Wind Monitor(white)<br />
<br />
' Red Wire -- CR3000 P2<br />
<br />
' Green Wire -- CR3000 SE2<br />
<br />
' Blue Wire -- CR3000 VX1<br />
<br />
' Clear Wire -- CR3000 AG<br />
<br />
' Black Wire -- CR3000 AG<br />
<br />
' White Wire -- CR3000 AG<br />
<br />
* Download data files from CR3000<br />
* upload new program<br />
* Align Wind sensors on ground as best as possible<br />
** first horizontal plane<br />
** second east-west<br />
* Raise tower<br />
** have Brie climb it to align sensors if necessary<br />
* Replace batteries in Garden Cam power case<br />
<br />
Evaporation Gauge<br />
*Build platform with pallets and plywood<br />
*attach gauge to pan with pipe<br />
*run wire through housing and into enclosure<br />
**' Evaporation Pan<br />
**' White Wire -- CR3000 SE16<br />
**' Red Wire -- CR3000 VX3 <br />
**' Black Wire -- CR3000 Signal Ground<br />
*Calibrate<br />
** Fill pan partway with water, measure height with ruler in mm<br />
** Measure voltage by reading the EvapLevelTemp variable on the program<br />
** Add more water, measure water depth in pan<br />
** Measure voltage<br />
** Calculate multiplier and offset using y = mx+b<br />
***m(multiplier) = (height1-height2)/(voltage2-voltage1)<br />
***b(offset) = height1-(m*voltage1)<br />
*Change multiplier and offset in program<br />
**download data<br />
**upload new program<br />
<br />
<br />
=== Additional tasks ===<br />
(grab ladder against back of tool shed to look into box)<br />
<br />
*download CR3000 + radio device config settings<br />
*level and alcohol swab radiometer (par) <br />
*level and alcohol swab 3 radiometers on old tower (net Rad, UVA, UVB)<br />
<br />
*Pluvio<br />
**Hole in mesh to craw in, 3 captive screws holding on outer shield<br />
**empty most of water inside plastic inner tub<br />
**remove any dead animals <br />
<br />
*note any damage<br />
*Make sure no water in battery box<br />
*inspect seals where wires go in<br />
*inspect solar panels<br />
<br />
== TODO ==<br />
*<s>TELEMETRY<s><br />
*<s>PR and purchase stuff</s><br />
*<s>update program for evap pan, wind sensors, snow depth quality number</s><br />
*<s>program NL100</s><br />
*<s>evap gauge base supplies and logistics</s><br />
*<s>learn ethernet cable connectors</s><br />
*GardenCam (how reset? what does PI want?)<br />
*<s>figure out where wind sensor go on data logger, and how to mount</s><br />
*<s>re-align wind sensor from basement</s><br />
*read pluvio manual<br />
*<s>find photo of evap pan base</s><br />
*<s>ask toolik for pallets</s><br />
*<s>new longer cable for wind sensor</s><br />
*<s>instal skype on iphone</s><br />
*<s>get wind sensor mounting pole from basement</s><br />
*<s>check types of wind instruments</s><br />
*write out plan<br />
*pack<br />
*<s>check how long cable on evap gauge is</s></div>137.229.29.72http://ocotal.iarc.uaf.edu/index.php?title=May_31-_June_6th,_2015_site_visit&diff=2281May 31- June 6th, 2015 site visit2015-05-30T05:32:36Z<p>137.229.29.72: </p>
<hr />
<div>== Instal evap pan ==<br />
*field calibrate<br />
*edit program<br />
*for platform<br />
**exterior grade plywood - home depot will cut it<br />
**exterior deck screws<br />
*calibrate in mm to get units in mm<br />
<br />
== Wind sensors replacement ==<br />
*calculate multiplier for wind direction sensor. for back calculation purposes<br />
*Replace wind direction sensors<br />
*align (declination: 18.5 degrees)<br />
** North (0/360 degrees) when nose points AWAY from box, for both sensors<br />
**aligned in office so that when nose faces same way as box, reads 180.<br />
*to install propeller, hand tighten then tighten with channel locks<br />
*both wind sensors can use same excitation port<br />
*White = 5106, Black = 5103<br />
<br />
== Telemetry ==<br />
Finish installing radio + ethernet for redundancy<br />
*old RF310B is in WQ in computer racks to left after enter<br />
**black box with campbell scientific marking<br />
**put timer on power source<br />
*radio connected to CR3000 with CS10 port gets power from this port as well<br />
*check config settings on NL201 nl201.toolik.uaf.edu should be: <br />
**HwAddr: 00:D0:2C:02:0D:73.<br />
**IP address: 137.229.91.81<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
*for NL100 I'm bring up<br />
**HwAddr (MAC address): 00d02c0004c0 <br />
**IP address: 137.229.91.82<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
<br />
== Items to bring up ==<br />
*alcohol swabs<br />
*compass <br />
*outlet timer for old radio<br />
*NL100<br />
*smart phone<br />
*evap gauge <br />
*two RM young wind sensors<br />
*sleeping bag<br />
*nut driver for tower base<br />
*drill + charger<br />
*tube for leveling platform<br />
*wood and screws for platform<br />
*zip ties<br />
*null modem cable for NL100 communication<br />
*cat5 cable and tools for creating connectors<br />
*wire to power NL100 from CR3000 AND ac adapter if outlet space<br />
*field laptop + charger<br />
*laptop + charger<br />
*plywood boards<br />
*field notebook<br />
*camera<br />
*tool bag<br />
*fish tape<br />
*electrical tape<br />
*ethernet-usb plug<br />
*serial-usb plug<br />
<br />
== Items to purchase ==<br />
*alcohol swabs<br />
*power strip<br />
*compass<br />
*32 AA batteries for GardenCam<br />
*plywood +screws for base<br />
<br />
== Tipping tower ==<br />
*grab 2 saw horses<br />
*undo one guy wire, loosen others<br />
*undo one leg bolts, loosen others<br />
** 2 bolts on each leg, take off both on one leg, just loosen bottom screw for other 2 legs<br />
*CAREFUL of sensor wires when lowering tower<br />
*have WD40 with me in case can't get wind sensor screws undone<br />
<br />
when raise tower, make turnbuckles taught but not too tight<br />
<br />
== PLAN ==<br />
<br />
===Telemetry===<br />
* plug in timer to old radio base<br />
* check config settings on NL201 in CPS shed<br />
* run cat5 line from radio in CPS shed<br />
* leave NL100 in enclosure, wire power to data logger or outlet<br />
<br />
===Wind Sensors + Garden Cam===<br />
*Alignmet <br />
**which way does tower tip and how is crossbar oriented <br />
**stake out east west <br />
* Tip Tower<br />
* Reset Garden Cam<br />
**remover flash drive (may need to cut tape for this)<br />
**download pics<br />
**clear drive<br />
*Replace Wind sensors<br />
**use old mounts or change if necessary<br />
**screw on propeller <br />
**alignment ring then sensor <br />
* zip tie wires and pull them into box<br />
* Wire Sensors<br />
' RM Young 5103 Wind Monitor (black)<br />
<br />
' Red Wire -- CR3000 P1<br />
<br />
' Green Wire -- CR3000 SE1<br />
<br />
' Blue Wire -- CR3000 VX1<br />
<br />
' Clear Wire -- CR3000 AG<br />
<br />
' Black Wire -- CR3000 AG<br />
<br />
' White Wire -- CR3000 AG<br />
<br />
' RM Young 5106 Wind Monitor(white)<br />
<br />
' Red Wire -- CR3000 P2<br />
<br />
' Green Wire -- CR3000 SE2<br />
<br />
' Blue Wire -- CR3000 VX1<br />
<br />
' Clear Wire -- CR3000 AG<br />
<br />
' Black Wire -- CR3000 AG<br />
<br />
' White Wire -- CR3000 AG<br />
<br />
* Download data files from CR3000<br />
* upload new program<br />
* Align Wind sensors on ground as best as possible<br />
** first horizonal plane<br />
** second east-west<br />
* Raise tower<br />
** have Brie climb it to align sensors if necessary<br />
* Replace batteries in Garden Cam power case<br />
<br />
<br />
=== Additional tasks ===<br />
(grab ladder against back of tool shed to look into box<br />
<br />
*download CR3000 + radio device config settings<br />
*level and alcohol swab radiometer (par) <br />
*level and alcohol swab 3 radiometers on old tower (net Rad, UVA, UVB)<br />
<br />
Pluvio<br />
*Hole in mesh to craw in, 3 captive screws holding on outer shield<br />
*empty most of water inside plastic inner tub<br />
*remove any dead animals <br />
<br />
*note any damage<br />
*Make sure no water in battery box<br />
<br />
*inspect seals where wires go in<br />
<br />
*inspect solar panels<br />
<br />
== TODO ==<br />
*<s>TELEMETRY<s><br />
*<s>PR and purchase stuff</s><br />
*<s>update program for evap pan, wind sensors, snow depth quality number</s><br />
*<s>program NL100</s><br />
*<s>evap gauge base supplies and logistics</s><br />
*<s>learn ethernet cable connectors</s><br />
*GardenCam (how reset? what does PI want?)<br />
*<s>figure out where wind sensor go on data logger, and how to mount</s><br />
*<s>re-align wind sensor from basement</s><br />
*read pluvio manual<br />
*<s>find photo of evap pan base</s><br />
*<s>ask toolik for pallets</s><br />
*<s>new longer cable for wind sensor</s><br />
*<s>instal skype on iphone</s><br />
*<s>get wind sensor mounting pole from basement</s><br />
*<s>check types of wind instruments</s><br />
*write out plan<br />
*pack<br />
*<s>check how long cable on evap gauge is</s></div>137.229.29.72http://ocotal.iarc.uaf.edu/index.php?title=May_31-_June_6th,_2015_site_visit&diff=2280May 31- June 6th, 2015 site visit2015-05-30T02:01:48Z<p>137.229.29.72: </p>
<hr />
<div>== Instal evap pan ==<br />
*field calibrate<br />
*edit program<br />
*for platform<br />
**exterior grade plywood - home depot will cut it<br />
**exterior deck screws<br />
*calibrate in mm to get units in mm<br />
<br />
== Wind sensors replacement ==<br />
*calculate multiplier for wind direction sensor. for back calculation purposes<br />
*Replace wind direction sensors<br />
*align (declination: 18.5 degrees)<br />
** North (0/360 degrees) when nose points AWAY from box, for both sensors<br />
**aligned in office so that when nose faces same way as box, reads 180.<br />
*to install propeller, hand tighten then tighten with channel locks<br />
*both wind sensors can use same excitation port<br />
*White = 5106, Black = 5103<br />
<br />
== Telemetry ==<br />
Finish installing radio + ethernet for redundancy<br />
*old RF310B is in WQ in computer racks to left after enter<br />
**black box with campbell scientific marking<br />
**put timer on power source<br />
*radio connected to CR3000 with CS10 port gets power from this port as well<br />
*check config settings on NL201 nl201.toolik.uaf.edu should be: <br />
**HwAddr: 00:D0:2C:02:0D:73.<br />
**IP address: 137.229.91.81<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
*for NL100 I'm bring up<br />
**HwAddr (MAC address): 00d02c0004c0 <br />
**IP address: 137.229.91.82<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
<br />
== Items to bring up ==<br />
*alcohol swabs<br />
*compass <br />
*outlet timer for old radio<br />
*NL100<br />
*smart phone<br />
*evap gauge <br />
*two RM young wind sensors<br />
*sleeping bag<br />
*nut driver for tower base<br />
*drill + charger<br />
*tube for leveling platform<br />
*wood and screws for platform<br />
*zip ties<br />
*null modem cable for NL100 communication<br />
*cat5 cable and tools for creating connectors<br />
*wire to power NL100 from CR3000 AND ac adapter if outlet space<br />
*field laptop + charger<br />
*laptop + charger<br />
*plywood boards<br />
*field notebook<br />
*camera<br />
*tool bag<br />
*fish tape<br />
*electrical tape<br />
*ethernet-usb plug<br />
*serial-usb plug<br />
<br />
== Items to purchase ==<br />
*alcohol swabs<br />
*power strip<br />
*compass<br />
*32 AA batteries for GardenCam<br />
*plywood +screws for base<br />
<br />
== Tipping tower ==<br />
*grab 2 saw horses<br />
*undo one guy wire, loosen others<br />
*undo one leg bolts, loosen others<br />
** 2 bolts on each leg, take off both on one leg, just loosen bottom screw for other 2 legs<br />
*CAREFUL of sensor wires when lowering tower<br />
*have WD40 with me in case can't get wind sensor screws undone<br />
<br />
when raise tower, make turnbuckles taught but not too tight<br />
<br />
== working on Tower ==<br />
<br />
gardenCam<br />
*Remove flash drive/SD card, download pics, clear it (may need to cut tape to access SD card)<br />
replace wind sensors, align direction<br />
<br />
<br />
== Additional tasks ==<br />
upload new CR3000 program (grab ladder against back of tool shed to look into box<br />
<br />
download CR3000 + radio device config settings<br />
<br />
level and alcohol swab radiometer (par) <br />
<br />
level and alcohol swab 3 radiometers on old tower (net Rad, UVA, UVB)<br />
<br />
GardenCam: replace batteries in box in box<br />
<br />
Pluvio<br />
*Hole in mesh to craw in, 3 captive screws holding on outer shield<br />
*empty most of water inside plastic inner tub<br />
*remove any dead animals <br />
<br />
note any damage<br />
Make sure no water in battery box<br />
<br />
inspect seals where wires go in<br />
<br />
inspect solar panels<br />
<br />
== TODO ==<br />
*<s>TELEMETRY<s><br />
*<s>PR and purchase stuff</s><br />
*<s>update program for evap pan, wind sensors, snow depth quality number</s><br />
*<s>program NL100</s><br />
*<s>evap gauge base supplies and logistics</s><br />
*<s>learn ethernet cable connectors</s><br />
*GardenCam (how reset? what does PI want?)<br />
*<s>figure out where wind sensor go on data logger, and how to mount</s><br />
*<s>re-align wind sensor from basement</s><br />
*read pluvio manual<br />
*<s>find photo of evap pan base</s><br />
*<s>ask toolik for pallets</s><br />
*<s>new longer cable for wind sensor</s><br />
*<s>instal skype on iphone</s><br />
*<s>get wind sensor mounting pole from basement</s><br />
*<s>check types of wind instruments</s><br />
*write out plan<br />
*pack<br />
*<s>check how long cable on evap gauge is</s></div>137.229.29.72http://ocotal.iarc.uaf.edu/index.php?title=May_31-_June_6th,_2015_site_visit&diff=2279May 31- June 6th, 2015 site visit2015-05-30T01:44:21Z<p>137.229.29.72: /* TODO */</p>
<hr />
<div>== Instal evap pan ==<br />
*field calibrate<br />
*edit program<br />
*for platform<br />
**exterior grade plywood - home depot will cut it<br />
**exterior deck screws<br />
*calibrate in mm to get units in mm<br />
<br />
== Wind sensors replacement ==<br />
*calculate multiplier for wind direction sensor. for back calculation purposes<br />
*Replace wind direction sensors<br />
*align (declination: 18.5 degrees)<br />
** North (0/360 degrees) when nose points AWAY from box, for both sensors<br />
**aligned in office so that when nose faces same way as box, reads 180.<br />
*to install propeller, hand tighten then tighten with channel locks<br />
*both wind sensors can use same excitation port<br />
<br />
== Telemetry ==<br />
Finish installing radio + ethernet for redundancy<br />
*old RF310B is in WQ in computer racks to left after enter<br />
**black box with campbell scientific marking<br />
**put timer on power source<br />
*radio connected to CR3000 with CS10 port gets power from this port as well<br />
*check config settings on NL201 nl201.toolik.uaf.edu should be: <br />
**HwAddr: 00:D0:2C:02:0D:73.<br />
**IP address: 137.229.91.81<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
*for NL100 I'm bring up<br />
**HwAddr (MAC address): 00d02c0004c0 <br />
**IP address: 137.229.91.82<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
<br />
== Items to bring up ==<br />
*alcohol swabs<br />
*compass <br />
*outlet timer for old radio<br />
*NL100<br />
*smart phone<br />
*evap gauge <br />
*two RM young wind sensors<br />
*sleeping bag<br />
*nut driver for tower base<br />
*drill + charger<br />
*tube for leveling platform<br />
*wood and screws for platform<br />
*zip ties<br />
*null modem cable for NL100 communication<br />
*cat5 cable and tools for creating connectors<br />
*wire to power NL100 from CR3000 AND ac adapter if outlet space<br />
*field laptop + charger<br />
*laptop + charger<br />
*plywood boards<br />
*field notebook<br />
*camera<br />
*tool bag<br />
*fish tape<br />
*electrical tape<br />
*ethernet-usb plug<br />
*serial-usb plug<br />
<br />
== Items to purchase ==<br />
*alcohol swabs<br />
*power strip<br />
*compass<br />
*32 AA batteries for GardenCam<br />
*plywood +screws for base<br />
<br />
== Tipping tower ==<br />
*grab 2 saw horses<br />
*undo one guy wire, loosen others<br />
*undo one leg bolts, loosen others<br />
** 2 bolts on each leg, take off both on one leg, just loosen bottom screw for other 2 legs<br />
*CAREFUL of sensor wires when lowering tower<br />
*have WD40 with me in case can't get wind sensor screws undone<br />
<br />
when raise tower, make turnbuckles taught but not too tight<br />
<br />
== working on Tower ==<br />
<br />
gardenCam<br />
*Remove flash drive/SD card, download pics, clear it (may need to cut tape to access SD card)<br />
replace wind sensors, align direction<br />
<br />
<br />
== Additional tasks ==<br />
upload new CR3000 program (grab ladder against back of tool shed to look into box<br />
<br />
download CR3000 + radio device config settings<br />
<br />
level and alcohol swab radiometer (par) <br />
<br />
level and alcohol swab 3 radiometers on old tower (net Rad, UVA, UVB)<br />
<br />
GardenCam: replace batteries in box in box<br />
<br />
Pluvio<br />
*Hole in mesh to craw in, 3 captive screws holding on outer shield<br />
*empty most of water inside plastic inner tub<br />
*remove any dead animals <br />
<br />
note any damage<br />
Make sure no water in battery box<br />
<br />
inspect seals where wires go in<br />
<br />
inspect solar panels<br />
<br />
== TODO ==<br />
*<s>TELEMETRY<s><br />
*<s>PR and purchase stuff</s><br />
*<s>update program for evap pan, wind sensors, snow depth quality number</s><br />
*<s>program NL100</s><br />
*<s>evap gauge base supplies and logistics</s><br />
*<s>learn ethernet cable connectors</s><br />
*GardenCam (how reset? what does PI want?)<br />
*<s>figure out where wind sensor go on data logger, and how to mount</s><br />
*<s>re-align wind sensor from basement</s><br />
*read pluvio manual<br />
*<s>find photo of evap pan base</s><br />
*<s>ask toolik for pallets</s><br />
*<s>new longer cable for wind sensor</s><br />
*<s>instal skype on iphone</s><br />
*<s>get wind sensor mounting pole from basement</s><br />
*check types of wind instruments<br />
*write out plan<br />
*pack<br />
*<s>check how long cable on evap gauge is</s></div>137.229.29.72http://ocotal.iarc.uaf.edu/index.php?title=May_31-_June_6th,_2015_site_visit&diff=2277May 31- June 6th, 2015 site visit2015-05-30T01:02:42Z<p>137.229.29.72: /* TODO */</p>
<hr />
<div>== Instal evap pan ==<br />
*field calibrate<br />
*edit program<br />
*for platform<br />
**exterior grade plywood - home depot will cut it<br />
**exterior deck screws<br />
*calibrate in mm to get units in mm<br />
<br />
== Wind sensors replacement ==<br />
*calculate multiplier for wind direction sensor. for back calculation purposes<br />
*Replace wind direction sensors<br />
*align (declination: 18.5 degrees)<br />
** North (0/360 degrees) when nose points AWAY from box, for both sensors<br />
**aligned in office so that when nose faces same way as box, reads 180.<br />
*to install propeller, hand tighten then tighten with channel locks<br />
*both wind sensors can use same excitation port<br />
<br />
== Telemetry ==<br />
Finish installing radio + ethernet for redundancy<br />
*old RF310B is in WQ in computer racks to left after enter<br />
**black box with campbell scientific marking<br />
**put timer on power source<br />
*radio connected to CR3000 with CS10 port gets power from this port as well<br />
*check config settings on NL201 nl201.toolik.uaf.edu should be: <br />
**HwAddr: 00:D0:2C:02:0D:73.<br />
**IP address: 137.229.91.81<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
*for NL100 I'm bring up<br />
**HwAddr (MAC address): 00d02c0004c0 <br />
**IP address: 137.229.91.82<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
<br />
== Items to bring up ==<br />
*alcohol swabs<br />
*compass <br />
*outlet timer for old radio<br />
*NL100<br />
*smart phone<br />
*evap gauge <br />
*two RM young wind sensors<br />
*sleeping bag<br />
*nut driver for tower base<br />
*drill + charger<br />
*tube for leveling platform<br />
*wood and screws for platform<br />
*zip ties<br />
*null modem cable for NL100 communication<br />
*cat5 cable and tools for creating connectors<br />
*wire to power NL100 from CR3000 AND ac adapter if outlet space<br />
*field laptop + charger<br />
*laptop + charger<br />
*plywood boards<br />
*field notebook<br />
*camera<br />
*tool bag<br />
*fish tape<br />
*electrical tape<br />
<br />
== Items to purchase ==<br />
*alcohol swabs<br />
*power strip<br />
*compass<br />
*32 AA batteries for GardenCam<br />
*plywood +screws for base<br />
<br />
== Tipping tower ==<br />
*grab 2 saw horses<br />
*undo one guy wire, loosen others<br />
*undo one leg bolts, loosen others<br />
** 2 bolts on each leg, take off both on one leg, just loosen bottom screw for other 2 legs<br />
*CAREFUL of sensor wires when lowering tower<br />
*have WD40 with me in case can't get wind sensor screws undone<br />
<br />
when raise tower, make turnbuckles taught but not too tight<br />
<br />
== working on Tower ==<br />
<br />
gardenCam<br />
*Remove flash drive/SD card, download pics, clear it (may need to cut tape to access SD card)<br />
replace wind sensors, align direction<br />
<br />
<br />
== Additional tasks ==<br />
upload new CR3000 program (grab ladder against back of tool shed to look into box<br />
<br />
download CR3000 + radio device config settings<br />
<br />
level and alcohol swab radiometer (par) <br />
<br />
level and alcohol swab 3 radiometers on old tower (net Rad, UVA, UVB)<br />
<br />
GardenCam: replace batteries in box in box<br />
<br />
Pluvio<br />
*Hole in mesh to craw in, 3 captive screws holding on outer shield<br />
*empty most of water inside plastic inner tub<br />
*remove any dead animals <br />
<br />
note any damage<br />
Make sure no water in battery box<br />
<br />
inspect seals where wires go in<br />
<br />
inspect solar panels<br />
<br />
== TODO ==<br />
*<s>TELEMETRY<s><br />
*<s>PR and purchase stuff</s><br />
*update program for evap pan, wind sensors, snow depth quality number<br />
*<s>program NL100</s><br />
*<s>evap gauge base supplies and logistics</s><br />
*<s>learn ethernet cable connectors</s><br />
*GardenCam (how reset? what does PI want?)<br />
*<s>figure out where wind sensor go on data logger, and how to mount</s><br />
*<s>re-align wind sensor from basement</s><br />
*read pluvio manual<br />
*<s>find photo of evap pan base</s><br />
*<s>ask toolik for pallets</s><br />
*<s>new longer cable for wind sensor</s><br />
*<s>instal skype on iphone</s><br />
*<s>get wind sensor mounting pole from basement</s><br />
*check types of wind instruments<br />
*write out plan<br />
*pack<br />
*<s>check how long cable on evap gauge is</s></div>137.229.29.72http://ocotal.iarc.uaf.edu/index.php?title=May_31-_June_6th,_2015_site_visit&diff=2276May 31- June 6th, 2015 site visit2015-05-30T00:55:37Z<p>137.229.29.72: </p>
<hr />
<div>== Instal evap pan ==<br />
*field calibrate<br />
*edit program<br />
*for platform<br />
**exterior grade plywood - home depot will cut it<br />
**exterior deck screws<br />
*calibrate in mm to get units in mm<br />
<br />
== Wind sensors replacement ==<br />
*calculate multiplier for wind direction sensor. for back calculation purposes<br />
*Replace wind direction sensors<br />
*align (declination: 18.5 degrees)<br />
** North (0/360 degrees) when nose points AWAY from box, for both sensors<br />
**aligned in office so that when nose faces same way as box, reads 180.<br />
*to install propeller, hand tighten then tighten with channel locks<br />
*both wind sensors can use same excitation port<br />
<br />
== Telemetry ==<br />
Finish installing radio + ethernet for redundancy<br />
*old RF310B is in WQ in computer racks to left after enter<br />
**black box with campbell scientific marking<br />
**put timer on power source<br />
*radio connected to CR3000 with CS10 port gets power from this port as well<br />
*check config settings on NL201 nl201.toolik.uaf.edu should be: <br />
**HwAddr: 00:D0:2C:02:0D:73.<br />
**IP address: 137.229.91.81<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
*for NL100 I'm bring up<br />
**HwAddr (MAC address): 00d02c0004c0 <br />
**IP address: 137.229.91.82<br />
**Subnet MASK: 255.255.255.192<br />
**Default Gateway/Router:137.229.91.65<br />
<br />
<br />
== Items to bring up ==<br />
*alcohol swabs<br />
*compass <br />
*outlet timer for old radio<br />
*NL100<br />
*smart phone<br />
*evap gauge <br />
*two RM young wind sensors<br />
*sleeping bag<br />
*nut driver for tower base<br />
*drill + charger<br />
*tube for leveling platform<br />
*wood and screws for platform<br />
*zip ties<br />
*null modem cable for NL100 communication<br />
*cat5 cable and tools for creating connectors<br />
*wire to power NL100 from CR3000 AND ac adapter if outlet space<br />
*field laptop + charger<br />
*laptop + charger<br />
*plywood boards<br />
*field notebook<br />
*camera<br />
*tool bag<br />
*fish tape<br />
*electrical tape<br />
<br />
== Items to purchase ==<br />
*alcohol swabs<br />
*power strip<br />
*compass<br />
*32 AA batteries for GardenCam<br />
*plywood +screws for base<br />
<br />
== Tipping tower ==<br />
*grab 2 saw horses<br />
*undo one guy wire, loosen others<br />
*undo one leg bolts, loosen others<br />
** 2 bolts on each leg, take off both on one leg, just loosen bottom screw for other 2 legs<br />
*CAREFUL of sensor wires when lowering tower<br />
*have WD40 with me in case can't get wind sensor screws undone<br />
<br />
when raise tower, make turnbuckles taught but not too tight<br />
<br />
== working on Tower ==<br />
<br />
gardenCam<br />
*Remove flash drive/SD card, download pics, clear it (may need to cut tape to access SD card)<br />
replace wind sensors, align direction<br />
<br />
<br />
== Additional tasks ==<br />
upload new CR3000 program (grab ladder against back of tool shed to look into box<br />
<br />
download CR3000 + radio device config settings<br />
<br />
level and alcohol swab radiometer (par) <br />
<br />
level and alcohol swab 3 radiometers on old tower (net Rad, UVA, UVB)<br />
<br />
GardenCam: replace batteries in box in box<br />
<br />
Pluvio<br />
*Hole in mesh to craw in, 3 captive screws holding on outer shield<br />
*empty most of water inside plastic inner tub<br />
*remove any dead animals <br />
<br />
note any damage<br />
Make sure no water in battery box<br />
<br />
inspect seals where wires go in<br />
<br />
inspect solar panels<br />
<br />
== TODO ==<br />
*TELEMETRY<br />
*<s>PR and purchase stuff</s><br />
*update program for evap pan, wind sensors, snow depth quality number<br />
*program NL100<br />
*<s>evap gauge base supplies and logistics</s><br />
*<s>learn ethernet cable connectors</s><br />
*GardenCam (how reset? what does PI want?)<br />
*<s>figure out where wind sensor go on data logger, and how to mount</s><br />
*<s>re-align wind sensor from basement</s><br />
*read pluvio manual<br />
*<s>find photo of evap pan base</s><br />
*<s>ask toolik for pallets</s><br />
*<s>new longer cable for wind sensor</s><br />
*<s>instal skype on iphone</s><br />
*<s>get wind sensor mounting pole from basement</s><br />
*check types of wind instruments<br />
*write out plan<br />
*pack<br />
*<s>check how long cable on evap gauge is</s></div>137.229.29.72http://ocotal.iarc.uaf.edu/index.php?title=May_31-_June_6th,_2015_site_visit&diff=2275May 31- June 6th, 2015 site visit2015-05-30T00:47:33Z<p>137.229.29.72: /* TODO */</p>
<hr />
<div>== Instal evap pan ==<br />
*field calibrate<br />
*edit program<br />
*for platform<br />
**exterior grade plywood - home depot will cut it<br />
**exterior deck screws<br />
*calibrate in mm to get units in mm<br />
<br />
== Wind sensors replacement ==<br />
*calculate multiplier for wind direction sensor. for back calculation purposes<br />
*Replace wind direction sensors<br />
*align (declination: 18.5 degrees)<br />
** North (0/360 degrees) when nose points AWAY from box, for both sensors<br />
**aligned in office so that when nose faces same way as box, reads 180.<br />
*to install propeller, hand tighten then tighten with channel locks<br />
*both wind sensors can use same excitation port<br />
<br />
== Telemetry ==<br />
Finish installing radio + ethernet for redundancy<br />
*old RF310B is in WQ in computer racks to left after enter<br />
**black box with campbell scientific marking<br />
**put timer on power source<br />
*radio connected to CR3000 with CS10 port gets power from this port as well<br />
<br />
<br />
== Items to bring up ==<br />
*alcohol swabs<br />
*compass <br />
*outlet timer for old radio<br />
*NL100<br />
*smart phone<br />
*evap gauge <br />
*two RM young wind sensors<br />
*sleeping bag<br />
*nut driver for tower base<br />
*drill + charger<br />
*tube for leveling platform<br />
*wood and screws for platform<br />
*zip ties<br />
*null modem cable for NL100 communication<br />
*cat5 cable and tools for creating connectors<br />
*wire to power NL100 from CR3000 AND ac adapter if outlet space<br />
*field laptop + charger<br />
*laptop + charger<br />
*plywood boards<br />
*field notebook<br />
*camera<br />
*tool bag<br />
*fish tape<br />
*electrical tape<br />
<br />
== Items to purchase ==<br />
*alcohol swabs<br />
*power strip<br />
*compass<br />
*32 AA batteries for GardenCam<br />
*plywood +screws for base<br />
<br />
== Tipping tower ==<br />
*grab 2 saw horses<br />
*undo one guy wire, loosen others<br />
*undo one leg bolts, loosen others<br />
** 2 bolts on each leg, take off both on one leg, just loosen bottom screw for other 2 legs<br />
*CAREFUL of sensor wires when lowering tower<br />
*have WD40 with me in case can't get wind sensor screws undone<br />
<br />
when raise tower, make turnbuckles taught but not too tight<br />
<br />
== working on Tower ==<br />
<br />
gardenCam<br />
*Remove flash drive/SD card, download pics, clear it (may need to cut tape to access SD card)<br />
replace wind sensors, align direction<br />
<br />
<br />
== Additional tasks ==<br />
upload new CR3000 program (grab ladder against back of tool shed to look into box<br />
<br />
download CR3000 + radio device config settings<br />
<br />
level and alcohol swab radiometer (par) <br />
<br />
level and alcohol swab 3 radiometers on old tower (net Rad, UVA, UVB)<br />
<br />
GardenCam: replace batteries in box in box<br />
<br />
Pluvio<br />
*Hole in mesh to craw in, 3 captive screws holding on outer shield<br />
*empty most of water inside plastic inner tub<br />
*remove any dead animals <br />
<br />
note any damage<br />
Make sure no water in battery box<br />
<br />
inspect seals where wires go in<br />
<br />
inspect solar panels<br />
<br />
== TODO ==<br />
*TELEMETRY<br />
*<s>PR and purchase stuff</s><br />
*update program for evap pan, wind sensors, snow depth quality number<br />
*program NL100<br />
*<s>evap gauge base supplies and logistics</s><br />
*<s>learn ethernet cable connectors</s><br />
*GardenCam (how reset? what does PI want?)<br />
*<s>figure out where wind sensor go on data logger, and how to mount</s><br />
*<s>re-align wind sensor from basement</s><br />
*read pluvio manual<br />
*<s>find photo of evap pan base</s><br />
*<s>ask toolik for pallets</s><br />
*<s>new longer cable for wind sensor</s><br />
*<s>instal skype on iphone</s><br />
*<s>get wind sensor mounting pole from basement</s><br />
*check types of wind instruments<br />
*write out plan<br />
*pack<br />
*<s>check how long cable on evap gauge is</s></div>137.229.29.72