IARC 207 Wiki - User contributions [en]

Dbm7

2008-09-23T23:48:39Z

137.229.71.46: /* 14 Jun 2008, emily ken */

= Lower Kadleroshilik River met =

{{todo}}

* Site needs new SR50 (spring 2008)
* measure distance from ground to SR50

=site logs=

== 9 Sept 2008, 3:22pm ADT Emily ==
* SR50 sensor looks good
* Sr50 distance to ground before trimming grass ranged from 117-122 cm, avg 120
* Added bark chips and trimmed vegetation, new avg distance is 112 cm,
* Changed SR50_ht in program from 120 cm to 112 cm
*Net radiometer was reading 0. Unwired and rewired but it didn't work
* Changed out net radiometer, pulled wire out of 1/2" flex conduit and then buried new
cable (not in conduit except at the sensor end and the tripod/instrument shelter end (~5 ft on each end)
* New S/N 72731 radiometer. Constant changed back at the lab from old 14.9 to new 12.9 uV/W/m2
* might want to try to rebury radiometer cable in conduit next trip. Need 3/4 " conduit.
* Flew over Shell Pingo and it look fine. Fence intact.

== 15 Jun 2008, emily & Ken==
* replaced sr50 snow sensor, new s/n c4384
* new sr50 distance to ground is 120 cm and changed it in program
* installed new electric fence (removed from dfr1)
* replace hmp45c head, new s/n c3210005 cal. Aug 2007
* added conduit/shielding

== 14 Jun 2008, emily ken==
* site visited, bear damage obvious
* guy wires loose on radiometer/snow tower
* hmp45c housing bent down
* snow sensor avg dist to ground 113.5 cm
* conduit needed, bear fence needed, shielding

== 14 June 2007, Ken I., Doug K. ==

* brief stop at site; notes made in field book the next day

* tripod look OK on quick look

* radiation pole leaning
** one guy anchor (north) pulled
** another guy turnbuckle was apart -- presumably unscrewed by wind/vibration

* adjusted 3rd (cast alumninum) turnbuckle to show some threads -- was at end of bolt

* drove 18-inch rebar at north anchor
** reset turnbuckle on SW guy

* rad pole firmly frozen/set in ground
** pushed (bent) pole to near-plumb

* radiometer mount failed with 2 lower ''ears'' bent, one cracked
** reset mount to level radiometer
** presume bear caused this damage

* snow depth height: 119 cm

* radiometer height: 119 cm

All projects

2008-09-17T23:46:58Z

137.229.71.46: /* WERC Research Stations -- Site Visit Logs & ToDo Lists */

= WERC Research Stations -- Site Visit Logs & ToDo Lists =
*[[Sept 2008 Field Trip - Emily and Ken]] General ToDo List
*[[June 2008 Field Trip - Emily and Ken]] General ToDo List

== North Slope Toolik SnowNet ==
** [[Toolik-Snow|Toolik Snow Precip Test Site (snownet)]]

== North Slope Kuparuk (Kane/NSF) ==
* main met sites:
** [[ukmet|Upper Kuparuk met]]
** [[fbmet|Franklin Bluffs met]]
** [[ibmet|Imnavait Basin met]]
** [[shmet|Sagwon Hill met]]
** [[wkmet|West Kuparuk met]]
** [[bpmet|Betty Pingo met]]
** [[wdmet|West Dock met]]
* precip sites in the headwaters:
* [[uh|Upper Headwaters]]
* [[eh|East Headwaters]]
* [[wh|West Headwaters]]
* [[nh|North Headwaters]]
* [[gcl|Green Cabin Lake]]
* stream gauging stations:
* [[ukgage|Upper Kuparuk gauge]]
* [[imnavaitweir|Imnavait Ck Weir]]
* [[putgage|Put River gauge]]
* radio base stations:
** [[sagriver|SagRiver Base]]
** [[toolik|ToolikLake Base]]
** [[deadhorse|Deadhorse Base]]
* radio repeater stations:
** [[smrep|Slope Mountain repeater]]
** [[ssrep|Sagwon Summit repeater]]
** [[ukrep|Upper Kuparuk Ridge repeater]]

== North Slope Bullen Project ==
* main met sites:
** [[dbm1|Accomplishment Creek met]] (DBM1)
** [[dbm2|Ribdon River met]] (DBM2)
** [[dbm3|Juniper Creek met]] (DBM3)
** [[dbm4|Sag-Ivishak met]] (DBM4)
** [[dbm5|Upper Kadleroshilik River met]] (DBM5)
** [[dbm6|Kavik Camp met]] (DBM6)
** [[dbm7|Lower Kadleroshilik River met]] (DBM7)
** [[dbm8|Bullen Point met]] (DBM8)
* radio repeater stations:
** [[dfr2|Slope Mtn2 repeater]] (DFR2)
** [[dbr2|Ribdon River repeater]] (DBR2)
** [[dbr3|Pogopuk Creek repeater]] (DBR3)
** [[dbr4|Kavik Ridge repeater]] (DBR4)
** [[dbr5|Franklin Bluffs repeater]] (DBR5)
** [[dfr3|Shell Pingo repeater]] (DFR3)

== North Slope Foothills Project ==
* main met sites:
** [[dfm1|South White Hills met]] (DFM1)
** [[dfm2|White Hills met]] (DFM2)
** [[dfm3|North White Hills met]] (DFM3)
** [[dfm4|Northwest Kuparuk met]] (DFM4)
* radio repeater stations:
** [[dfr1|Kakukturat Mountain repeater]] (DFR1, decommissioned jun08)
** [[dfr3|Shell Pingo repeater]] (DFR3)
** [[dfr4|Imnaviat Mountain repeater]] (DFR4, replaced DFR1)

Toolik-Snow

2008-09-17T22:13:29Z

137.229.71.46:

= Toolik Snow and Precipitation Test Site (Snownet) =

= site logs =
== 10 Sept 2008, Emily and Ken ==
Site established on Sept 11, 2008

Installed two SR50s
*SR50E (E indicates East sensor) sensor has '''bark chips''' and trimmed vegetation under sensor
**Sensor has NO orange tape on the end of the grey cable (in instrument shelter)
**S/N C4802 installed 9/10/08
**Measured SR50 distance to the ground is 160, 163, 163, 160, 160, 159 cm average = 161
**Uses control port 3 on datalogger

*SR50W (W indicates West sensor) sensor has no bark chips, no trimmed vegetation, natural conditions, control site
**Sensor has orange tape at the end of the grey cable (into the instrument shelter) indicating it is the control
** S/N C5011 installed 9/10/08
**Measured SR50 distance to ground 180, 175, 176, 174, 178, avg 176.6
**Ground surface below the sensor is not level, grass is approximately 24 to 40 cm tall.
**Uses control port 5 on datalogger

RM Young installed
*S/N

GWS YSIx3 thermistor
*needs housing, currently under instrument shelter box

HMP45C cable onsite
*Needs sensor
*Needs housing

Barometric Pressure
*needs rewiring?

Solar panel installed on 2 fenceposts

Toolik-Snow

2008-09-17T22:12:37Z

137.229.71.46: /* 10 Sept 2008, Emily and Ken */

= Toolik Snow and Precipitation Test Site (Snownet) =

= site logs =
== 10 Sept 2008, Emily and Ken ==
Site established on Sept 11, 2008

Installed two SR50s
*SR50E (E indicates East sensor) sensor has '''bark chips''' and trimmed vegetation under sensor
**Sensor has NO orange tape on the end of the grey cable (in instrument shelter)
**S/N C4802 installed 9/10/08
**Measured SR50 distance to the ground is 160, 163, 163, 160, 160, 159 cm average = 161

*SR50W (W indicates West sensor) sensor has no bark chips, no trimmed vegetation, natural conditions, control site
**Sensor has orange tape at the end of the grey cable (into the instrument shelter) indicating it is the control
** S/N C5011 installed 9/10/08
**Measured SR50 distance to ground 180, 175, 176, 174, 178, avg 176.6
**Ground surface below the sensor is not level, grass is approximately 24 to 40 cm tall.

RM Young installed
*S/N

GWS YSIx3 thermistor
*needs housing, currently under instrument shelter box

HMP45C cable onsite
*Needs sensor
*Needs housing

Barometric Pressure
*needs rewiring?

Solar panel installed on 2 fenceposts

Toolik-Snow

2008-09-17T22:09:51Z

137.229.71.46:

= Toolik Snow and Precipitation Test Site (Snownet) =

= site logs =
== 10 Sept 2008, Emily and Ken ==
Site established on Sept 11, 2008

Installed two SR50s
*SR50E (E indicates East) sensor has '''bark chips''' and trimmed vegetation under sensor
**Sensor has NO orange tape on the end of the grey cable
**S/N C4802 installed 9/10/08
**Measured SR50 distance to the ground is 160, n163, 163, 160, 160, 159 cm average = 161

*SR50W (W indicates West) sensor has no bark chips, no trimmed vegetation, natural conditions, control
**Sensor has orange tape at the end of the grey cable (into the instrument shelter) indicating it is the control
** S/N C5011 installed 9/10/08
**Measured SR50 distance to ground 180, 175, 176, 174, 178, avg 176.6
**Surface is unlevel, grass is 24 to 40 cm tall.

RM Young installed
*S/N

GWS YSIx3 thermistor
*needs housing, currently under instrument shelter box

HMP45C cable onsite
*Needs sensor
*Needs housing

Barometric Pressure
*needs rewiring?

Solar panel installed on 2 fenceposts

Toolik-Snow

2008-09-17T22:09:32Z

137.229.71.46:

= Toolik Snow and Precipitation Test Site (Snownet) =

= site logs =
== 10 Sept 2008, Emily and Ken ==
Site established on Sept 11, 2008
Installed two SR50s
*SR50E (E indicates East) sensor has '''bark chips''' and trimmed vegetation under sensor
**Sensor has NO orange tape on the end of the grey cable
**S/N C4802 installed 9/10/08
**Measured SR50 distance to the ground is 160, n163, 163, 160, 160, 159 cm average = 161

*SR50W (W indicates West) sensor has no bark chips, no trimmed vegetation, natural conditions, control
**Sensor has orange tape at the end of the grey cable (into the instrument shelter) indicating it is the control
** S/N C5011 installed 9/10/08
**Measured SR50 distance to ground 180, 175, 176, 174, 178, avg 176.6
**Surface is unlevel, grass is 24 to 40 cm tall.

RM Young installed
*S/N

GWS YSIx3 thermistor
*needs housing, currently under instrument shelter box

HMP45C cable onsite
*Needs sensor
*Needs housing

Barometric Pressure
*needs rewiring?

Solar panel installed on 2 fenceposts

Toolik-Snow

2008-09-17T22:07:54Z

137.229.71.46:

= Toolik Snow and Precipitation Test Site (Snownet) =

= site logs =
== 10 Sept 2008, Emily and Ken ==
Site established on Sept 11, 2008
Installed two SR50s
*SR50E (E indicates East) sensor has '''bark chips''' and trimmed vegetation under sensor
**Sensor has NO orange tape on the end of the grey cable
**S/N C4802 installed 9/10/08
**Measured SR50 distance to the ground is 160, n163, 163, 160, 160, 159 cm average = 161

*SR50W (W indicates West) sensor has no bark chips, no trimmed vegetation, natural conditions, control
**Sensor has orange tape at the end of the grey cable (into the instrument shelter) indicating it is the control
** S/N C5011 installed 9/10/08
**Measured SR50 distance to ground 180, 175, 176, 174, 178, avg 176.6
**Surface is unlevel, grass is 24 to 40 cm tall.

RM Young installed
*S/N

Toolik-Snow

2008-09-17T22:07:16Z

137.229.71.46:

= Toolik Snow and Precipitation Test Site (Snownet) =

= site logs =
== 10 Sept 2008, Emily and Ken ==
Site established on Sept 11, 2008
Installed two SR50s
*SR50E (E indicates East) sensor has [[bark chips]] and trimmed vegetation under sensor
**Sensor has NO orange tape on the end of the grey cable
**S/N C4802 installed 9/10/08
**Measured SR50 distance to the ground is 160, n163, 163, 160, 160, 159 cm average = 161

*SR50W (W indicates West) sensor has no bark chips, no trimmed vegetation, natural conditions, control
**Sensor has orange tape at the end of the grey cable (into the instrument shelter) indicating it is the control
** S/N C5011 installed 9/10/08
**Measured SR50 distance to ground 180, 175, 176, 174, 178, avg 176.6
**Surface is unlevel, grass is 24 to 40 cm tall.

RM Young installed
*S/N

All projects

2008-09-17T21:59:02Z

137.229.71.46:

= WERC Research Stations -- Site Visit Logs & ToDo Lists =
*[[June 2008 Field Trip - Emily and Ken]] General ToDo List

== North Slope Toolik SnowNet ==
** [[Toolik-Snow|Toolik Snow Precip Test Site (snownet)]]

== North Slope Kuparuk (Kane/NSF) ==
* main met sites:
** [[ukmet|Upper Kuparuk met]]
** [[fbmet|Franklin Bluffs met]]
** [[ibmet|Imnavait Basin met]]
** [[shmet|Sagwon Hill met]]
** [[wkmet|West Kuparuk met]]
** [[bpmet|Betty Pingo met]]
** [[wdmet|West Dock met]]
* precip sites in the headwaters:
* [[uh|Upper Headwaters]]
* [[eh|East Headwaters]]
* [[wh|West Headwaters]]
* [[nh|North Headwaters]]
* [[gcl|Green Cabin Lake]]
* stream gauging stations:
* [[ukgage|Upper Kuparuk gauge]]
* [[imnavaitweir|Imnavait Ck Weir]]
* [[putgage|Put River gauge]]
* radio base stations:
** [[sagriver|SagRiver Base]]
** [[toolik|ToolikLake Base]]
** [[deadhorse|Deadhorse Base]]
* radio repeater stations:
** [[smrep|Slope Mountain repeater]]
** [[ssrep|Sagwon Summit repeater]]
** [[ukrep|Upper Kuparuk Ridge repeater]]

== North Slope Bullen Project ==
* main met sites:
** [[dbm1|Accomplishment Creek met]] (DBM1)
** [[dbm2|Ribdon River met]] (DBM2)
** [[dbm3|Juniper Creek met]] (DBM3)
** [[dbm4|Sag-Ivishak met]] (DBM4)
** [[dbm5|Upper Kadleroshilik River met]] (DBM5)
** [[dbm6|Kavik Camp met]] (DBM6)
** [[dbm7|Lower Kadleroshilik River met]] (DBM7)
** [[dbm8|Bullen Point met]] (DBM8)
* radio repeater stations:
** [[dfr2|Slope Mtn2 repeater]] (DFR2)
** [[dbr2|Ribdon River repeater]] (DBR2)
** [[dbr3|Pogopuk Creek repeater]] (DBR3)
** [[dbr4|Kavik Ridge repeater]] (DBR4)
** [[dbr5|Franklin Bluffs repeater]] (DBR5)
** [[dfr3|Shell Pingo repeater]] (DFR3)

== North Slope Foothills Project ==
* main met sites:
** [[dfm1|South White Hills met]] (DFM1)
** [[dfm2|White Hills met]] (DFM2)
** [[dfm3|North White Hills met]] (DFM3)
** [[dfm4|Northwest Kuparuk met]] (DFM4)
* radio repeater stations:
** [[dfr1|Kakukturat Mountain repeater]] (DFR1, decommissioned jun08)
** [[dfr3|Shell Pingo repeater]] (DFR3)
** [[dfr4|Imnaviat Mountain repeater]] (DFR4, replaced DFR1)

All projects

2008-09-17T21:57:46Z

137.229.71.46: /* North Slope SnowNet */

= WERC Research Stations -- Site Visit Logs & ToDo Lists =
*[[June 2008 Field Trip - Emily and Ken]] General ToDo List

== North Slope Toolik SnowNet ==
** [[Toolik|Toolik Snow Precip Test Site (snownet)]]

== North Slope Kuparuk (Kane/NSF) ==
* main met sites:
** [[ukmet|Upper Kuparuk met]]
** [[fbmet|Franklin Bluffs met]]
** [[ibmet|Imnavait Basin met]]
** [[shmet|Sagwon Hill met]]
** [[wkmet|West Kuparuk met]]
** [[bpmet|Betty Pingo met]]
** [[wdmet|West Dock met]]
* precip sites in the headwaters:
* [[uh|Upper Headwaters]]
* [[eh|East Headwaters]]
* [[wh|West Headwaters]]
* [[nh|North Headwaters]]
* [[gcl|Green Cabin Lake]]
* stream gauging stations:
* [[ukgage|Upper Kuparuk gauge]]
* [[imnavaitweir|Imnavait Ck Weir]]
* [[putgage|Put River gauge]]
* radio base stations:
** [[sagriver|SagRiver Base]]
** [[toolik|ToolikLake Base]]
** [[deadhorse|Deadhorse Base]]
* radio repeater stations:
** [[smrep|Slope Mountain repeater]]
** [[ssrep|Sagwon Summit repeater]]
** [[ukrep|Upper Kuparuk Ridge repeater]]

== North Slope Bullen Project ==
* main met sites:
** [[dbm1|Accomplishment Creek met]] (DBM1)
** [[dbm2|Ribdon River met]] (DBM2)
** [[dbm3|Juniper Creek met]] (DBM3)
** [[dbm4|Sag-Ivishak met]] (DBM4)
** [[dbm5|Upper Kadleroshilik River met]] (DBM5)
** [[dbm6|Kavik Camp met]] (DBM6)
** [[dbm7|Lower Kadleroshilik River met]] (DBM7)
** [[dbm8|Bullen Point met]] (DBM8)
* radio repeater stations:
** [[dfr2|Slope Mtn2 repeater]] (DFR2)
** [[dbr2|Ribdon River repeater]] (DBR2)
** [[dbr3|Pogopuk Creek repeater]] (DBR3)
** [[dbr4|Kavik Ridge repeater]] (DBR4)
** [[dbr5|Franklin Bluffs repeater]] (DBR5)
** [[dfr3|Shell Pingo repeater]] (DFR3)

== North Slope Foothills Project ==
* main met sites:
** [[dfm1|South White Hills met]] (DFM1)
** [[dfm2|White Hills met]] (DFM2)
** [[dfm3|North White Hills met]] (DFM3)
** [[dfm4|Northwest Kuparuk met]] (DFM4)
* radio repeater stations:
** [[dfr1|Kakukturat Mountain repeater]] (DFR1, decommissioned jun08)
** [[dfr3|Shell Pingo repeater]] (DFR3)
** [[dfr4|Imnaviat Mountain repeater]] (DFR4, replaced DFR1)

All projects

2008-09-17T21:57:31Z

137.229.71.46:

= WERC Research Stations -- Site Visit Logs & ToDo Lists =
*[[June 2008 Field Trip - Emily and Ken]] General ToDo List

== North Slope SnowNet ==
** [[Toolik|Toolik Snow Precip Test Site (snownet)]]

== North Slope Kuparuk (Kane/NSF) ==
* main met sites:
** [[ukmet|Upper Kuparuk met]]
** [[fbmet|Franklin Bluffs met]]
** [[ibmet|Imnavait Basin met]]
** [[shmet|Sagwon Hill met]]
** [[wkmet|West Kuparuk met]]
** [[bpmet|Betty Pingo met]]
** [[wdmet|West Dock met]]
* precip sites in the headwaters:
* [[uh|Upper Headwaters]]
* [[eh|East Headwaters]]
* [[wh|West Headwaters]]
* [[nh|North Headwaters]]
* [[gcl|Green Cabin Lake]]
* stream gauging stations:
* [[ukgage|Upper Kuparuk gauge]]
* [[imnavaitweir|Imnavait Ck Weir]]
* [[putgage|Put River gauge]]
* radio base stations:
** [[sagriver|SagRiver Base]]
** [[toolik|ToolikLake Base]]
** [[deadhorse|Deadhorse Base]]
* radio repeater stations:
** [[smrep|Slope Mountain repeater]]
** [[ssrep|Sagwon Summit repeater]]
** [[ukrep|Upper Kuparuk Ridge repeater]]

== North Slope Bullen Project ==
* main met sites:
** [[dbm1|Accomplishment Creek met]] (DBM1)
** [[dbm2|Ribdon River met]] (DBM2)
** [[dbm3|Juniper Creek met]] (DBM3)
** [[dbm4|Sag-Ivishak met]] (DBM4)
** [[dbm5|Upper Kadleroshilik River met]] (DBM5)
** [[dbm6|Kavik Camp met]] (DBM6)
** [[dbm7|Lower Kadleroshilik River met]] (DBM7)
** [[dbm8|Bullen Point met]] (DBM8)
* radio repeater stations:
** [[dfr2|Slope Mtn2 repeater]] (DFR2)
** [[dbr2|Ribdon River repeater]] (DBR2)
** [[dbr3|Pogopuk Creek repeater]] (DBR3)
** [[dbr4|Kavik Ridge repeater]] (DBR4)
** [[dbr5|Franklin Bluffs repeater]] (DBR5)
** [[dfr3|Shell Pingo repeater]] (DFR3)

== North Slope Foothills Project ==
* main met sites:
** [[dfm1|South White Hills met]] (DFM1)
** [[dfm2|White Hills met]] (DFM2)
** [[dfm3|North White Hills met]] (DFM3)
** [[dfm4|Northwest Kuparuk met]] (DFM4)
* radio repeater stations:
** [[dfr1|Kakukturat Mountain repeater]] (DFR1, decommissioned jun08)
** [[dfr3|Shell Pingo repeater]] (DFR3)
** [[dfr4|Imnaviat Mountain repeater]] (DFR4, replaced DFR1)

All projects

2008-09-17T21:56:45Z

137.229.71.46:

= WERC Research Stations -- Site Visit Logs & ToDo Lists =
*[[June 2008 Field Trip - Emily and Ken]] General ToDo List

== North Slope SnowNet ==
* [[Toolik|Toolik Snow Precip Test Site (snownet)]]

== North Slope Kuparuk (Kane/NSF) ==
* main met sites:
** [[ukmet|Upper Kuparuk met]]
** [[fbmet|Franklin Bluffs met]]
** [[ibmet|Imnavait Basin met]]
** [[shmet|Sagwon Hill met]]
** [[wkmet|West Kuparuk met]]
** [[bpmet|Betty Pingo met]]
** [[wdmet|West Dock met]]
* precip sites in the headwaters:
* [[uh|Upper Headwaters]]
* [[eh|East Headwaters]]
* [[wh|West Headwaters]]
* [[nh|North Headwaters]]
* [[gcl|Green Cabin Lake]]
* stream gauging stations:
* [[ukgage|Upper Kuparuk gauge]]
* [[imnavaitweir|Imnavait Ck Weir]]
* [[putgage|Put River gauge]]
* radio base stations:
** [[sagriver|SagRiver Base]]
** [[toolik|ToolikLake Base]]
** [[deadhorse|Deadhorse Base]]
* radio repeater stations:
** [[smrep|Slope Mountain repeater]]
** [[ssrep|Sagwon Summit repeater]]
** [[ukrep|Upper Kuparuk Ridge repeater]]

== North Slope Bullen Project ==
* main met sites:
** [[dbm1|Accomplishment Creek met]] (DBM1)
** [[dbm2|Ribdon River met]] (DBM2)
** [[dbm3|Juniper Creek met]] (DBM3)
** [[dbm4|Sag-Ivishak met]] (DBM4)
** [[dbm5|Upper Kadleroshilik River met]] (DBM5)
** [[dbm6|Kavik Camp met]] (DBM6)
** [[dbm7|Lower Kadleroshilik River met]] (DBM7)
** [[dbm8|Bullen Point met]] (DBM8)
* radio repeater stations:
** [[dfr2|Slope Mtn2 repeater]] (DFR2)
** [[dbr2|Ribdon River repeater]] (DBR2)
** [[dbr3|Pogopuk Creek repeater]] (DBR3)
** [[dbr4|Kavik Ridge repeater]] (DBR4)
** [[dbr5|Franklin Bluffs repeater]] (DBR5)
** [[dfr3|Shell Pingo repeater]] (DFR3)

== North Slope Foothills Project ==
* main met sites:
** [[dfm1|South White Hills met]] (DFM1)
** [[dfm2|White Hills met]] (DFM2)
** [[dfm3|North White Hills met]] (DFM3)
** [[dfm4|Northwest Kuparuk met]] (DFM4)
* radio repeater stations:
** [[dfr1|Kakukturat Mountain repeater]] (DFR1, decommissioned jun08)
** [[dfr3|Shell Pingo repeater]] (DFR3)
** [[dfr4|Imnaviat Mountain repeater]] (DFR4, replaced DFR1)

Dfm3

2008-09-17T21:54:59Z

137.229.71.46:

= North White Hills met =

{{todo}}

=site logs=

==10 Sept 2008 10:30am ADT Emily & Joel H.==
*SR50 distance before trimming vegetation and adding bark was 110-114 cm (program reads 9 cm snow depth)
*After adding bark and trimming vegetation the new distance from Sr50 to ground is 106 cm
*changed program from 115 cm to 106 cm SR50_ht
*tightened guy wires

==16 Jun 2008, Emily & Ken ==
* The tipping bucket funnel was blown off the precip gage. Data before this date will be bad.
* Reinstalled the tipping bucket funnel
* Electric fence is working, added 3 more fence posts
* distance from sr50 to ground avg ~ 115cm
* changed HMP45c head
** new s/n c3210010
** old s/n B0110048
* replaced sr50 sensor
**old s/n C4789
**new s/n C2405
**new distance is ~115 cm (no change), did not change the program
*added conduit

== 12 June 2007, Ken I., Doug K. ==

* installed electric fence with 3 posts

* found HMP45C beneath solar panel; installed it; values look plausible, close to other sensors

* measured SR50 height at 116 cm
** changed program from 111 to 116 cm

* suspect radiation pole has ''frost-jacked'' about 5 cm during winter. Guy wires are '''very''' taut. No room on turnbuckles to loosen.

* confirm K&Z factor 14.3 as per program
** s/n 052056
** bubble slightly off; adjusted
** measured 100 cm to ground

* no barometer in instrument enclosure

* fox droppings below tripod

* own pellet beneath radiation pole

* battery box was dry, also instrument enclosure. Desicant checked, not replaced.

* did '''NOT''' make an entry in the site field log book

Dfm4

2008-09-17T21:53:10Z

137.229.71.46:

= Site to do list =

=Site Logs =

== 10 Sept 2008 8:52am ADT Emily & Joel Homan ==
* Uneven terrain under SR50. Distance to ground variable from 116cm-127 cm
* Trimmed vegetation and added bark chips
* Measured distance under sensor - avg ~110 cm
* Changed distance in program from 115 cm to 110 cm.
* added electric fence
*next trip bring spare yellow brackets to help keep wire off fenceposts.

== 16 Jun 2008 Emily & Ken ==
*After reviewing data at Toolik, data shows damage to anemometer, hmp45c, and sr50
*sr50 data went from 12 cm to 25 cm in one hour
*site visit indicated an animal (most likely a bear) ripped wires out of the instrument box:
**YSIx3
**HMP45C
**anememoter
**blu/red wire from junction box
**sr50?
*SR50 distance (old) ~115 cm avg.
*replaced SR 50
** old s/n c5011
** new s/n c4387
** distance to ground is the same
*HMP45C head replaced
** old s/n B0110061
** new s/n C1440007
*loose wires, rewired all sensor wires that came loose out of box

*Also note that the trench for the cables running from the tipod to the snow sensor was dug up and buried cables/conduit is exposed.
* the bear also pulled the ysix3 and hmp45c out of its housing and out of the bottom of the box, but they were not broken

== May 2008 ==
Note EKY 6/6/08, Bob and Jeff visited this site in may 08 and fixed the antennae. Site is now transmitting data.

Dfm4

2008-09-17T21:52:36Z

137.229.71.46:

= Site to do list =

=Site Logs =

== 10 Sept 2008 Emily & Joel Homan ==
* Uneven terrain under SR50. Distance to ground variable from 116cm-127 cm
* Trimmed vegetation and added bark chips
* Measured distance under sensor - avg ~110 cm
* Changed distance in program from 115 cm to 110 cm.
* added electric fence
*next trip bring spare yellow brackets to help keep wire off fenceposts.

== 16 Jun 2008 Emily & Ken ==
*After reviewing data at Toolik, data shows damage to anemometer, hmp45c, and sr50
*sr50 data went from 12 cm to 25 cm in one hour
*site visit indicated an animal (most likely a bear) ripped wires out of the instrument box:
**YSIx3
**HMP45C
**anememoter
**blu/red wire from junction box
**sr50?
*SR50 distance (old) ~115 cm avg.
*replaced SR 50
** old s/n c5011
** new s/n c4387
** distance to ground is the same
*HMP45C head replaced
** old s/n B0110061
** new s/n C1440007
*loose wires, rewired all sensor wires that came loose out of box

*Also note that the trench for the cables running from the tipod to the snow sensor was dug up and buried cables/conduit is exposed.
* the bear also pulled the ysix3 and hmp45c out of its housing and out of the bottom of the box, but they were not broken

== May 2008 ==
Note EKY 6/6/08, Bob and Jeff visited this site in may 08 and fixed the antennae. Site is now transmitting data.

Dfm4

2008-09-17T21:48:29Z

137.229.71.46:

= Site to do list =

=Site Logs =

== 10 Sept 2008 Emily & Joel Homan ==
*

== 16 Jun 2008 Emily & Ken ==
*After reviewing data at Toolik, data shows damage to anemometer, hmp45c, and sr50
*sr50 data went from 12 cm to 25 cm in one hour
*site visit indicated an animal (most likely a bear) ripped wires out of the instrument box:
**YSIx3
**HMP45C
**anememoter
**blu/red wire from junction box
**sr50?
*SR50 distance (old) ~115 cm avg.
*replaced SR 50
** old s/n c5011
** new s/n c4387
** distance to ground is the same
*HMP45C head replaced
** old s/n B0110061
** new s/n C1440007
*loose wires, rewired all sensor wires that came loose out of box

*Also note that the trench for the cables running from the tipod to the snow sensor was dug up and buried cables/conduit is exposed.
* the bear also pulled the ysix3 and hmp45c out of its housing and out of the bottom of the box, but they were not broken

== May 2008 ==
Note EKY 6/6/08, Bob and Jeff visited this site in may 08 and fixed the antennae. Site is now transmitting data.

Dfr3

2008-09-17T21:44:34Z

137.229.71.46:

= Shell Pingo repeater, DFR3 =

= site logs =

== 9 Sept 2008, 5:32pm ADT Emily ==
*Flew over shell pingo and it looked fine from the air.
*E-fence still intact.

== 15 Jun 2008, 12:00 ADT Emily & Ken ==
* installed new electric fence, used the new fence post solar panel
* loaded program

== 14 Jun 2008, Emily & Ken ==
*Bear Damage at site
* new HMP45AC installed, s/n W2040077
* rewired the YSIx3
* Ken reinstalled the radio antennae cable

Dbm7

2008-09-17T21:43:36Z

137.229.71.46:

= Lower Kadleroshilik River met =

{{todo}}

* Site needs new SR50 (spring 2008)
* measure distance from ground to SR50

=site logs=

== 9 Sept 2008, 3:22pm ADT Emily ==
* SR50 sensor looks good
* Sr50 distance to ground before trimming grass ranged from 117-122 cm, avg 120
* Added bark chips and trimmed vegetation, new avg distance is 112 cm,
* Changed SR50_ht in program from 120 cm to 112 cm
*Net radiometer was reading 0. Unwired and rewired but it didn't work
* Changed out net radiometer, pulled wire out of 1/2" flex conduit and then buried new
cable (not in conduit except at the sensor end and the tripod/instrument shelter end (~5 ft on each end)
* New S/N 72731 radiometer. Constant changed back at the lab from old 14.9 to new 12.9 uV/W/m2
* might want to try to rebury radiometer cable in conduit next trip. Need 3/4 " conduit.
* Flew over Shell Pingo and it look fine. Fence intact.

== 15 Jun 2008, emily & Ken==
* replaced sr50 snow sensor, new s/n c4384
* new sr50 distance to ground is 120 cm and changed it in program
* installed new electric fence (removed from dfr1)
* replace hmp45c head, new s/n c3210005 cal. Aug 2007
* added conduit/shielding

== 14 Jun 2008, emily ken==
* site visited, bear damage obvious
* guy wires loose on radiometer/snow tower
* hmp45c housing bent down
* snow sensor avg dist to ground 113.5 cm
* conduit needed, bear fence needed, shielding

== 14 June 2007, Ken I., Doug K.

* brief stop at site; notes made in field book the next day

* tripod look OK on quick look

* radiation pole leaning
** one guy anchor (north) pulled
** another guy turnbuckle was apart -- presumably unscrewed by wind/vibration

* adjusted 3rd (cast alumninum) turnbuckle to show some threads -- was at end of bolt

* drove 18-inch rebar at north anchor
** reset turnbuckle on SW guy

* rad pole firmly frozen/set in ground
** pushed (bent) pole to near-plumb

* radiometer mount failed with 2 lower ''ears'' bent, one cracked
** reset mount to level radiometer
** presume bear caused this damage

* snow depth height: 119 cm

* radiometer height: 119 cm

Dbm8

2008-09-17T21:39:00Z

137.229.71.46:

= Bullen Point met =

* return/replace site logbook to enclosure

=site logs=

== 9 Sept 2008, 2:40pm ADT Emily ==
*SR50 sensor looks good
*SR50 distance to ground before trimming vegetation was ~104 cm
*Trimmed vegetation and added bark chips, new average distance is ~102 cm
*Updated program (old program Sr50 offset is 112 cm, new value is 102 cm)
*tightened fence and guy wires to radiation and SR50 poles

== 14 Jun 2008, 12:00pm ADT Emily and Ken ==
* replaced snow sensor. Old s/n 4800, new s/n C2333
* measured distance from ground to sensor
**old distance was 112cm, new distance is the same
* rewired soil moisture sensors: wiring is as follows:
** bl-bl, red-red, gre-gre, oran-white
* added conduit

== 29 Aug2007, Ken I.==
Transcribed by EKY
* SR50 replaced old w/ new SR50M-45, S/N C4800 PROM SR50V13, SIG 56809
* Used Rob's 45' lead
* Repulled YSIx3 soil temp surface sensors
* Installed new YSIx3 sensors but 2 of 3 were bad
* all cables are in conduit
* SR50 to ground distance is 108, but grass is 10-18 cm higher
* tightened electric fence, but....?

== 14 June 2007, Ken I., Doug K. ==

* net radiometer replaced
** s/n 052046
** 14.6 uV/W-m^2
** 120 cm centerline sensor to ground

* SR50 -- cable missing, not replaced (had one, but too short)

* RMYoung & HMP45C cables put in flex conduit on tripod

* no GWS-YSI sensor, and no conduit was left for it

* AT shields braced with mast/enclosure bracket to strengthen

* antenna cable wrapped with nylon spiral wrap; no way to pull into conduit

* conduits '''wired''' (using tie-wire) to enclosure entry fittings to secure
* soil temp profile cable: added strain relief using hose clamp & cord; load was on the multiplexer terminals
* added cord inside enclosure to secure extra/loose cables inside
* replaced rain gauge
** model: TR-525USW
** s/n: 37655-1205
** collector/funnel secured with hose clamp
** screen secured with electrical tape

== 13 June 2007, Ken I., Doug K. ==

* installed electric fence with 3 posts
* no time to fix site cables
* '''LOTS''' of fox scat around site, many chewed cables
* accidentally removed site logbook

Dbm6

2008-09-17T21:36:08Z

137.229.71.46:

== TODO ==

*Check soil temperature,
*Measure distance from ground to snow sensor,
*reset antennae radio guy wires.

= site logs =

== Sept 9 2008 1:20pm ADT Emily ==
*Possible bear charging station (according to Sue at Kavik) but no visible damage.
*Install bear fence next year
*Sr50 distance to ground is 143 cm before trimming vegetation
*Trimmed vegetation and added bark below sensor
*New distance is ~140cm (data logger program read 148 cm) and so changed to 140 cm in program.

== 13 Jun 2008 Emily & Ken ==
* snow sensor distance is ~148 cm, changed old value of 150cm to new value of 148cm.

== 03 Sept 2007, Ken I. ==
Transcribed EKY
* downloaded data, saved old program, updated new program
* site looks good
* antennae radio pole vertical but the guys are loose, need to reset

== 29 Aug 2007, Ken I ==
Transcribed EKY
* Tripod looks good
* Precip good
* Radiation pole, 1 guy detached
**reset radiation pole turn buckles and wired them to secure
* Net rad is level, 111 cm to ground from sensor, but grass is 10 cm higher, birch (?) to 15 cm higher
* SR50 is 148 cm to ground
* Rotated SR50 pole to secure to guy wire via tie wrap

Shmet

2008-09-17T18:32:05Z

137.229.71.46:

== Site Logs ==

== Sept 6, 2008 Emily and Rob ==
*Rob pulled out the radiometers
*the snow sensor (S/N C2331) looks okay, but ground is somewhat unlevel
*Average distance from ground to sensor before trimming vegetation and leveling ground is 174 cm
*After leveling ground (no bark chips added) and trimming vegetation
**New average distance is 172 and it is more level.
**Program changed from 180 cm to 172 cm

== 01 Sept 07, Rob and Ken ==
*Swapped SR50, old s/n C2333, new s/n 2330, SR50M-45
*new xdcr kit, tested in lab 30 or 31 Aug 07
*170 cm to ground, grass at 163 cm

Wkmet

2008-09-17T18:29:30Z

137.229.71.46:

= West Kuparuk met =

{{todo}}

* '''take replacement screed stake''' (4 feet long?) to site
* replace SE anchor with driving head attached; remove/recover driving head
* '''take 2-1/2-foot unistrut''' & 1-inch by 1/4 or 5/16 inch bolts for 3rd ''fencer'' stand leg

=site logs=

==Sept 5 2008, Emily Ken ==

*put away radiometers, 1 nut lost, bring more when redeploying in spring
*installed new tripod with SR50. Added bark chips. S/N C4797, calibrated 9/5/08
*Average distance ground to SR50 is 154 cm
*Loaded new program for West Kuparuk Met

== 12 June 2007, Ken I., Doug K. ==

* installed electric fence with 6 posts, one wire at about 3-1/2 feet height

* tried to drive main tower anchors, but drove ''driving head'' onto SE screed stake to stay...

* fence charger ''cranepod'' has only 2 unistrut legs; 3rd leg is copper ground rod hose-clamped to hinge hasp;

* lost ''new age'' pliers somewhere near site

Dfm1

2008-09-17T18:27:19Z

137.229.71.46: /* Sept 5, 2008, Emily & Ken */

= South White Hills met =

{{todo}}

* need flex conduit/armoring on antenna, AT sensor cables
* bring snap link/carabiner for white instrument enclosure

= site logs =

== Sept 5, 2008, Emily & Ken ==
*tightened guy wires, radiation/SR50 pole was very crooked
*Old SR50 S/n C4798 and distance to ground was variable (125 cm - 149 cm) due to uneven ground
*Installed a new SR50 and moved it 1 foot to the north where the ground was more level
*New SR50 S/N C4789, calibrated by R. Gieck 9/5/08
*Reloaded new program onto datalogger (failure during transmission via radios)
*Added bark chips under SR50 and trimmed vegetation
*New SR50 distance from sensor to ground is 134.5 average and I put it into the program.
*Program now reads 1.13 cm of snow, an improvement from the previous reading.
*rain gage was leveled, it was very unlevel.

Future tasks:
*bring out one more fence post
*site needs shielding and conduit

== 13 July 2007, Ken I. ==

* replaced missing HMP45C
** S/N C1440027
** calibrated April 2007
* yellow tags on electric fence were already taped
* fence works (ouch)
* site generally looks good
* rain gauge funnel not secured
* no carabiner/screw link on white box; used tie wrap/wire tie

== 9 June 2007, Ken I., Dan R. ==

* site generally looks good

* radiation pole is firm & true
** ''bird post'' broken off from net radiometer, found beneath

* tripod guys are taut

* no HMP sensor; cable cut cleanly, apparently at base of missing sensor

* owl pellets below solar panel; bird droppings on solar panel & battery box

* installed electric fence

Dfm1

2008-09-17T18:26:19Z

137.229.71.46:

= South White Hills met =

{{todo}}

* need flex conduit/armoring on antenna, AT sensor cables
* bring snap link/carabiner for white instrument enclosure

= site logs =

== Sept 5, 2008, Emily & Ken ==
*tightened guy wires, radiation/SR50 pole was very crooked
*Old SR50 S/n C4798 and distance to ground was variable (125 cm - 149 cm) due to uneven ground
*Installed a new SR50 and moved it 1 foot to the north where the ground was more level
*New SR50 S/N C4789, calibrated by R. Gieck 9/5/08
*Reloaded new program onto datalogger (failure during transmission via radios)
*Added bark chips under SR50 and trimmed vegetation
*New SR50 distance from sensor to ground is 134.5 average and I put it into the program.
*Program now reads 1.13 cm of snow, an improvement from the previous reading.
*rain gage was leveled, it was very crooked.

== 13 July 2007, Ken I. ==

* replaced missing HMP45C
** S/N C1440027
** calibrated April 2007
* yellow tags on electric fence were already taped
* fence works (ouch)
* site generally looks good
* rain gauge funnel not secured
* no carabiner/screw link on white box; used tie wrap/wire tie

== 9 June 2007, Ken I., Dan R. ==

* site generally looks good

* radiation pole is firm & true
** ''bird post'' broken off from net radiometer, found beneath

* tripod guys are taut

* no HMP sensor; cable cut cleanly, apparently at base of missing sensor

* owl pellets below solar panel; bird droppings on solar panel & battery box

* installed electric fence

North Slope Kuparuk

2008-08-28T22:18:00Z

137.229.71.46:

This project is funded by the National Science Foundation. The met stations covered by this project include:
* West Dock,
*Franklin Bluffs,
*Sagwon,
*Betty Pingo,
*Imnaviat Met,
*Imnaviat Flume,
*Putiligiak River gage,
*Upper Kuparuk Met & Gage,
*North Headwaters,
*Upper Headwaters,
*West Heatwaters,
*East Headwaters, and
*Green Cabin Lake.

North Slope Bullen

2008-08-28T22:17:06Z

137.229.71.46:

This project is funded by the Alaska Department of Natural Resources and funds stations in the DBM/DBR series:
*DBM1 Accomplishment Cr
*DBM2 Ribdon
*DBM3 Juniper
*DBM4 Sag-Ivishak
*DBM5 Upper Kadleroshilik
*DBM6 Kavik
*DBM7 Kadleroshilik
*DBM8 Bullen
*DBR1
*DBR3
*DBR3
*DBR4

North Slope Bullen

2008-08-28T22:16:22Z

137.229.71.46:

This project is funded by the Alaska Department of Natural Resources and funds stations in the DBM/DBR series:
DBM1 Accomplishment Cr
DBM2 Ribdon
DBM3 Juniper
DBM4 Sag-Ivishak
DBM5 Upper Kadleroshilik
DBM6 Kavik
DBM7 Kadleroshilik
DBM8 Bullen
DBR1
DBR3
DBR3
DBR4

North Slope Kuparuk

2008-08-28T22:13:24Z

137.229.71.46:

This project is funded by the National Science Foundation. The met stations covered by this project include West Dock, Franklin Bluffs, Sagwon, Betty Pingo, Imnaviat Met, Imnaviat Flume, Putiligiak River gage, Upper Kuparuk Met & Gage, North Headwaters, Upper Headwaters, West Heatwaters, East Headwaters, and Green Cabin Lake.

Sept 2008 Field Trip - Emily and Ken

2008-08-28T22:03:14Z

137.229.71.46:

This is a to do list written by Emily and Ken detailing work to be done on the Sept 4-11 field trip.
Helicopter is available approximately Sept 5-7 and we extended it until we are finished (8-10).
We will visit West Kuparuk and Bullen/Foothills sites, along with Put River, Imnaviat Basin, Upper Kuparuk for stream gaging, so bring waders and rubber boots.
Remember to make reservations at Toolik (& bring your own sleeping bag/sheets/blankets/pillow)

[[NSF Sites Notes from Bob]] (Emily and Rob can take care of these NSF sites on the trip up to Prudhoe).

'''Note:''' Sites are grouped by area.
''Ken add stations that need conduit and bear fencing.''

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area) helicopter sites==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4 :
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) helicopter sites ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) helicopter sites ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== ''Other TO DO things not helicopter related'' ==

== Emily and Rob head up to Deadhorse and gage the Put River Sept 6-7 ==
*Remember to check [[NSF Sites Notes from Bob]]

== Imnaviat Flume ==
*Install a new larger solar panel and battery
*Gage the site
*repairs to wingwalls as needed
*See [[NSF Sites Notes from Bob]]

== Upper Kuparuk ==
*Gage the site
*See [[NSF Sites Notes from Bob]]

== Toolik snow sensor test site ==

*Toolik Geonor T200B precip gauge site prep

** select site location
*** need 120VAC power
** install concrete base block
*** dig hole for about 6CF concrete
*** prepare template for 4 bolts, 225cm apart
*** mix and place concrete
*** set bolts in place; orient N-S and E-W, leave 6" above surface
*** protect from elements etc. until set
** sensor to be installed later...

*Install SR50 snow sensor
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

Sept 2008 Field Trip - Emily and Ken

2008-08-28T22:02:27Z

137.229.71.46:

This is a to do list written by Emily and Ken detailing work to be done on the Sept 4-11 field trip.
Helicopter is available approximately Sept 5-7 and we extended it until we are finished (8-10).
We will visit West Kuparuk and Bullen/Foothills sites, along with Put River, Imnaviat Basin, Upper Kuparuk for stream gaging, so bring waders and rubber boots.
Remember to make reservations at Toolik (& bring your own sleeping bag/sheets/blankets/pillow)

[[NSF Sites Notes from Bob]] (Emily and Rob can take care of these NSF sites on the trip up to Prudhoe).

'''Note:''' Sites are grouped by area.
''Ken add stations that need conduit and bear fencing.''

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area) helicopter sites==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4 :
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) helicopter sites ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) helicopter sites ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== ''Other TO DO things not helicopter related'' ==

== Emily and Rob head up to Deadhorse and gage the Put River Sept 6-7 ==
*Remember to check [[NSF Sites Notes from Bob]]

== Imnaviat Flume ==
*Install a new larger solar panel and battery
*Gage the site
*repairs to wingwalls as needed
*See [[Imnaviat Basin New]]

== Upper Kuparuk ==
*Gage the site
*See [[Upper Kuparuk Met]]

== Toolik snow sensor test site ==

*Toolik Geonor T200B precip gauge site prep

** select site location
*** need 120VAC power
** install concrete base block
*** dig hole for about 6CF concrete
*** prepare template for 4 bolts, 225cm apart
*** mix and place concrete
*** set bolts in place; orient N-S and E-W, leave 6" above surface
*** protect from elements etc. until set
** sensor to be installed later...

*Install SR50 snow sensor
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

Sept 2008 Field Trip - Emily and Ken

2008-08-28T22:01:10Z

137.229.71.46:

This is a to do list written by Emily and Ken detailing work to be done on the Sept 4-11 field trip.
Helicopter is available approximately Sept 5-7 and we extended it until we are finished (8-10).
We will visit West Kuparuk and Bullen/Foothills sites, along with Put River, Imnaviat Basin, Upper Kuparuk for stream gaging, so bring waders and rubber boots.
Remember to make reservations at Toolik (& bring your own sleeping bag/sheets/blankets/pillow)

[[NSF Sites Notes from Bob]] (Emily and Rob can take care of these NSF sites on the trip up to Prudhoe).

'''Note:''' Sites are grouped by area.
''Ken add stations that need conduit and bear fencing.''

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area) helicopter sites==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4 :
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) helicopter sites ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) helicopter sites ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== ''Other TO DO things not helicopter related'' ==

== Emily and Rob head up to Deadhorse and gage the Put River Sept 6-7 ==
*Remember to check [[NSF Sites Notes from Bob]]

== Imnaviat Flume ==
*Install a new larger solar panel and battery
*Gage the site
*repairs to wingwalls as needed

== Upper Kuparuk ==
*Gage the site

== Toolik snow sensor test site ==

*Toolik Geonor T200B precip gauge site prep

** select site location
*** need 120VAC power
** install concrete base block
*** dig hole for about 6CF concrete
*** prepare template for 4 bolts, 225cm apart
*** mix and place concrete
*** set bolts in place; orient N-S and E-W, leave 6" above surface
*** protect from elements etc. until set
** sensor to be installed later...

*Install SR50 snow sensor
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

Sept 2008 Field Trip - Emily and Ken

2008-08-28T22:00:06Z

137.229.71.46:

This is a to do list written by Emily and Ken detailing work to be done on the Sept 4-11 field trip.
Helicopter is available approximately Sept 5-7 and we extended it until we are finished (8-10).
We will visit West Kuparuk and Bullen/Foothills sites, along with Put River, Imnaviat Basin, Upper Kuparuk for stream gaging, so bring waders and rubber boots.
Remember to make reservations at Toolik (& bring your own sleeping bag/sheets/blankets/pillow)

[[NSF Sites Notes from Bob]] (Emily and Rob can take care of these NSF sites on the trip up to Prudhoe).

'''Note:''' Sites are grouped by area.
''Ken add stations that need conduit and bear fencing.''

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area) helicopter sites==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4 :
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) helicopter sites ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) helicopter sites ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== ''Other TO DO things not helicopter related'' ==

== Emily and Rob head up to Deadhorse and gage the Put River Sept 6-7 ==
*Remember to check [[NSF Sites Notes from Bob]]

== Imnaviat Flume ==
*Install a new larger solar panel and battery
*Gage the site
*repairs to wingwalls as needed

== Toolik snow sensor test site ==

*Toolik Geonor T200B precip gauge site prep

** select site location
*** need 120VAC power
** install concrete base block
*** dig hole for about 6CF concrete
*** prepare template for 4 bolts, 225cm apart
*** mix and place concrete
*** set bolts in place; orient N-S and E-W, leave 6" above surface
*** protect from elements etc. until set
** sensor to be installed later...

*Install SR50 snow sensor
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

Sept 2008 Field Trip - Emily and Ken

2008-08-28T21:59:23Z

137.229.71.46: /* Emily and Ken head up to Betty Pingo and the Put to gage Sept 6-7 */

This is a to do list written by Emily and Ken detailing work to be done on the Sept 4-11 field trip.
Helicopter is available approximately Sept 5-7 and we extended it until we are finished (8-10).
We will visit West Kuparuk and Bullen/Foothills sites, along with Put River, Imnaviat Basin, Upper Kuparuk for stream gaging, so bring waders and rubber boots.
Remember to make reservations at Toolik (& bring your own sleeping bag/sheets/blankets/pillow)

[[NSF Sites Notes from Bob]] (Emily and Rob can take care of these NSF sites on the trip up to Prudhoe).

'''Note:''' Sites are grouped by area.
''Ken add stations that need conduit and bear fencing.''

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area)==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4:
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== ''Other TO DO things not helicopter related'' ==

== Emily and Rob head up to Deadhorse and gage the Put River Sept 6-7 ==
*Remember to check [[NSF Sites Notes from Bob]]

== Imnaviat Flume ==
*Install a new larger solar panel and battery
*Gage the site
*repairs to wingwalls as needed

== Toolik snow sensor test site ==

*Toolik Geonor T200B precip gauge site prep

** select site location
*** need 120VAC power
** install concrete base block
*** dig hole for about 6CF concrete
*** prepare template for 4 bolts, 225cm apart
*** mix and place concrete
*** set bolts in place; orient N-S and E-W, leave 6" above surface
*** protect from elements etc. until set
** sensor to be installed later...

*Install SR50 snow sensor
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

Sept 2008 Field Trip - Emily and Ken

2008-08-28T21:58:33Z

137.229.71.46:

This is a to do list written by Emily and Ken detailing work to be done on the Sept 4-11 field trip.
Helicopter is available approximately Sept 5-7 and we extended it until we are finished (8-10).
We will visit West Kuparuk and Bullen/Foothills sites, along with Put River, Imnaviat Basin, Upper Kuparuk for stream gaging, so bring waders and rubber boots.
Remember to make reservations at Toolik (& bring your own sleeping bag/sheets/blankets/pillow)

[[NSF Sites Notes from Bob]] (Emily and Rob can take care of these NSF sites on the trip up to Prudhoe).

'''Note:''' Sites are grouped by area.
''Ken add stations that need conduit and bear fencing.''

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area)==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4:
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== ''Other TO DO things not helicopter related'' ==

== Emily and Ken head up to Betty Pingo and the Put to gage Sept 6-7 ==
*Remember to check [[NSF Sites Notes from Bob]]

== Imnaviat Flume ==
*Install a new larger solar panel and battery
*Gage the site
*repairs to wingwalls as needed

== Toolik snow sensor test site ==

*Toolik Geonor T200B precip gauge site prep

** select site location
*** need 120VAC power
** install concrete base block
*** dig hole for about 6CF concrete
*** prepare template for 4 bolts, 225cm apart
*** mix and place concrete
*** set bolts in place; orient N-S and E-W, leave 6" above surface
*** protect from elements etc. until set
** sensor to be installed later...

*Install SR50 snow sensor
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

Sept 2008 Field Trip - Emily and Ken

2008-08-28T21:56:00Z

137.229.71.46:

This is a to do list written by Emily and Ken detailing work to be done on the Sept 4-11 field trip.
Helicopter is available approximately Sept 5-7 and we extended it until we are finished (8-10).
We will visit West Kuparuk and Bullen/Foothills sites, along with Put River, Imnaviat Basin, Upper Kuparuk for stream gaging, so bring waders and rubber boots.
Remember to make reservations at Toolik (& bring your own sleeping bag/sheets/blankets/pillow)

[[NSF Sites Notes from Bob]] (Emily and Rob can take care of these NSF sites on the trip up to Prudhoe).

'''Note:''' Sites are grouped by area.
''Ken add stations that need conduit and bear fencing.''

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area)==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4:
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Imnaviat Flume ==
*Install a new larger solar panel and battery
*Gage the site
*repairs to wingwalls as needed

== Toolik snow sensor test site ==

*Toolik Geonor T200B precip gauge site prep

** select site location
*** need 120VAC power
** install concrete base block
*** dig hole for about 6CF concrete
*** prepare template for 4 bolts, 225cm apart
*** mix and place concrete
*** set bolts in place; orient N-S and E-W, leave 6" above surface
*** protect from elements etc. until set
** sensor to be installed later...

*Install SR50 snow sensor
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

Main Page

2008-08-28T21:54:39Z

137.229.71.46:

= WERC research sites wiki =

This is a collaborative website for people involved with WERC's research stations, in any of several different projects:

== site logs and todo lists ==
* [[all projects]] todo and site logs
* [[Sept 2008 Field Trip - Emily and Ken]] General ToDo List
* [[June 2008 Field Trip - Emily and Ken]] General ToDo List
* [[North Slope Kuparuk]]
* [[North Slope Bullen]]
* [[North Slope Foothills]]
* [[Seward Peninsula Sites]]

== WERC field books ==
* [[ken 2005 1]]
* [[ken 2005-2]]
* [[ken 2006-1]]
* [[ken 2007-1]]
* [[ken 2008-2]]

== Field notes and procedures ==

* Using the [[Sontek handheld ADP]]
* Using the [[Sontek Rivercat and Toughbook]]
* Using the [[Flo-Mate]] flow meter
* Using the [[RDI StreamPro ADCP]]
* [[WERC Snow Survey Procedure]]

== Some other good things to know ==
* [[North Slope Training Procedures - Bullen/Foothills/Kuparuk projects]]
* [[Common Instrumentation]] links
* [[Software]] we use
* [[New Person]] in the department guide
* [[Troubleshooting]] sensors etc.
* [[Common Sensor Wiring]]
* [[Datalogger programming]]

== ''Meta-topics'' on the use & setup of the WERC wiki ==
* editing wiki pages
* [[implementing site todo lists and logs]]

North Slope Training Procedures - Bullen/Foothills/Kuparuk projects

2008-08-28T21:53:21Z

137.229.71.46:

== North Slope Training Procedures ==

* First make sure you have taken the UAF Safe Driving Course if you will be driving a UAF vehicle. Visit [[New Person]] for details
* Generally we stay at Toolik or in Deadhorse. Review the Toolik website for information about Toolik
* Sign up and ask your supervisor to pay for the NSTC class offered at Alaska West Training Center
** The NSTC class allows you to be unescorted on the oil fields (near Betty Pingo/West Dock Sites)
* Check with Rob Gieck and find out what BP/Conoco Philips Training you will need to take to enter the oilfields (Betty Pingo/West Dock)
** Bear Safety videos
** Smith System driving training
** Cultural Awareness
** Health Safety and Environmental compliance videos

New Person

2008-08-28T21:52:45Z

137.229.71.46:

When first coming to work you'll need to pass the driver safety class to drive a university vehicle. You can take the class online here:

[http://classes.uaf.edu UAF Blackboard website]

login: fnXXX (your uaf email address)

Do a course search for 'Driver Safety' and take this class.

An easier way is to just go to the UAF Safety website:

[http://www.uaf.edu/safety/ UAF Safety]

and go to the Training Button and select Driver's Training.
There are other trainings and guidance documents available here such as Lab Safety and Remote Travel safety and planning.

If you will be working on the North Slope, you need to visit Rob Gieck and get the North Slope training videos. You may also need to sign up for the North Slope Training through Alaska West Training Center if you will be unescorted on the oil fields. Go to [[North Slope Training Procedures - Bullen/Foothills/Kuparuk projects]] for more details

North Slope Training Procedures - Bullen/Foothills/Kuparuk projects

2008-08-28T21:51:20Z

137.229.71.46: /* North Slope Training Procedures */

== North Slope Training Procedures ==

* First make sure you have taken the UAF Safe Driving Course if you will be driving a UAF vehicle
* Generally we stay at Toolik or in Deadhorse. Review the Toolik website for information about Toolik
* Sign up and ask your supervisor to pay for the NSTC class offered at Alaska West Training Center
** The NSTC class allows you to be unescorted on the oil fields (near Betty Pingo/West Dock Sites)
* Check with Rob Gieck and find out what BP/Conoco Philips Training you will need to take to enter the oilfields (Betty Pingo/West Dock)
** Bear Safety videos
** Smith System driving training
** Cultural Awareness
** Health Safety and Environmental compliance videos

North Slope Training Procedures - Bullen/Foothills/Kuparuk projects

2008-08-28T21:50:35Z

137.229.71.46: /* North Slope Training Procedures */

== North Slope Training Procedures ==

* First make sure you have taken the UAF Safe Driving Course if you will be driving a UAF vehicle
* Sign up and ask your supervisor to pay for the NSTC class offered at Alaska West Training Center
** The NSTC class allows you to be unescorted on the oil fields (near Betty Pingo/West Dock Sites)
* Check with Rob Gieck and find out what BP/Conoco Philips Training you will need to take to enter the oilfields (Betty Pingo/West Dock)
** Bear Safety videos
** Smith System driving training
** Cultural Awareness
** Health Safety and Environmental compliance videos

North Slope Training Procedures - Bullen/Foothills/Kuparuk projects

2008-08-28T21:49:42Z

137.229.71.46:

== North Slope Training Procedures ==

* First make sure you have taken the UAF Safe Driving Course
* Sign up and ask your supervisor to pay for the NSTC class offered at Alaska West Training Center
** The NSTC class allows you to be unescorted on the oil fields (near Betty Pingo/West Dock Sites)
* Check with Rob Gieck and find out what BP/Conoco Philips Training you will need to take to enter the oilfields (Betty Pingo/West Dock)

Main Page

2008-08-28T21:47:21Z

137.229.71.46: /* Some other good things to know */

= WERC research sites wiki =

This is a collaborative website for people involved with WERC's research stations, in any of several different projects:

== site logs and todo lists ==
* [[all projects]] todo and site logs
* [[Sept 2008 Field Trip - Emily and Ken]] General ToDo List
* [[June 2008 Field Trip - Emily and Ken]] General ToDo List
* [[North Slope Kuparuk]]
* [[North Slope Bullen]]
* [[North Slope Foothills]]
* [[Seward Peninsula Sites]]

== WERC field books ==
* [[ken 2005 1]]
* [[ken 2005-2]]
* [[ken 2006-1]]
* [[ken 2007-1]]
* [[ken 2008-2]]

== Field notes and procedures ==

* Using the [[Sontek handheld ADP]]
* Using the [[Sontek Rivercat and Toughbook]]
* Using the [[Flo-Mate]] flow meter
* Using the [[RDI StreamPro ADCP]]
* [[WERC Snow Survey Procedure]]

== Some other good things to know ==
* [[Common Instrumentation]] links
* [[Software]] we use
* [[New Person]] in the department guide
* [[Troubleshooting]] sensors etc.
* [[Common Sensor Wiring]]
* [[Datalogger programming]]
* [[North Slope Training Procedures - Bullen/Foothills/Kuparuk projects]]

--

== ''Meta-topics'' on the use & setup of the WERC wiki ==
* editing wiki pages
* [[implementing site todo lists and logs]]

Sept 2008 Field Trip - Emily and Ken

2008-08-28T21:43:00Z

137.229.71.46:

This is a to do list written by Emily and Ken detailing work to be done on the Sept 4-11 field trip.
Helicopter is available approximately Sept 5-7 and we extended it until we are finished (8-10).
We will visit West Kuparuk and Bullen/Foothills sites, along with Put River, Imnaviat Basin, Upper Kuparuk for stream gaging.

''Ken add stations that need conduit and bear fencing.''

[[NSF Sites Notes from Bob]] (Emily and Rob can take care of these NSF sites on the trip up to Prudhoe).

'''Note:''' Sites are grouped by area.

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area)==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4:
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Imnaviat Flume ==
*Install a new larger solar panel and battery
*Gage the site
*repairs to wingwalls as needed

== Toolik snow sensor test site ==

*Toolik Geonor T200B precip gauge site prep

** select site location
*** need 120VAC power
** install concrete base block
*** dig hole for about 6CF concrete
*** prepare template for 4 bolts, 225cm apart
*** mix and place concrete
*** set bolts in place; orient N-S and E-W, leave 6" above surface
*** protect from elements etc. until set
** sensor to be installed later...

*Install SR50 snow sensor
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

Sept 2008 Field Trip - Emily and Ken

2008-08-28T21:41:00Z

137.229.71.46: /* Toolik SR50 snow sensor test site */

This is a to do list written by Emily and Ken detailing work to be done on the Sept 4-11 field trip.
Helicopter is available approximately Sept 5-7 and we extended it until we are finished (8-10).
We will visit West Kuparuk and Bullen/Foothills sites, along with Put River, Imnaviat Basin, Upper Kuparuk for stream gaging.

''Ken add stations that need conduit and bear fencing.''

[[NSF Sites Notes from Bob]] (Emily and Rob can take care of these NSF sites on the trip up to Prudhoe).

'''Note:''' Sites are grouped by area.

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area)==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4:
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Imnaviat Flume ==
*Install a new larger solar panel and battery
*Gage the site
*repairs to wingwalls as needed

== Toolik SR50 snow sensor test site ==

Install SR50 test site at Toolik
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

== Toolik Geonor T200B precip gauge site prep ==

* select site location
** need 120VAC power
* install concrete base block
** dig hole for about 6CF concrete
** prepare template for 4 bolts, 225cm apart
** mix and place concrete
** set bolts in place; orient N-S and E-W, leave 6" above surface
** protect from elements etc. until set
* sensor to be installed later...

Sept 2008 Field Trip - Emily and Ken

2008-08-28T21:40:37Z

137.229.71.46: /* Imnaviat Flume */

This is a to do list written by Emily and Ken detailing work to be done on the Sept 4-11 field trip.
Helicopter is available approximately Sept 5-7 and we extended it until we are finished (8-10).
We will visit West Kuparuk and Bullen/Foothills sites, along with Put River, Imnaviat Basin, Upper Kuparuk for stream gaging.

''Ken add stations that need conduit and bear fencing.''

[[NSF Sites Notes from Bob]] (Emily and Rob can take care of these NSF sites on the trip up to Prudhoe).

'''Note:''' Sites are grouped by area.

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area)==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4:
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Imnaviat Flume ==
*Install a new larger solar panel and battery
*Gage the site
*repairs to wingwalls as needed

== Toolik SR50 snow sensor test site ==

*Install SR50 test site
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

== Toolik Geonor T200B precip gauge site prep ==

* select site location
** need 120VAC power
* install concrete base block
** dig hole for about 6CF concrete
** prepare template for 4 bolts, 225cm apart
** mix and place concrete
** set bolts in place; orient N-S and E-W, leave 6" above surface
** protect from elements etc. until set
* sensor to be installed later...

Sept 2008 Field Trip - Emily and Ken

2008-08-28T21:37:58Z

137.229.71.46:

This is a to do list written by Emily and Ken detailing work to be done on the Sept 4-11 field trip.
Helicopter is available approximately Sept 5-7 and we extended it until we are finished (8-10).
We will visit West Kuparuk and Bullen/Foothills sites, along with Put River, Imnaviat Basin, Upper Kuparuk for stream gaging.

''Ken add stations that need conduit and bear fencing.''

[[NSF Sites Notes from Bob]] (Emily and Rob can take care of these NSF sites on the trip up to Prudhoe).

'''Note:''' Sites are grouped by area.

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area)==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4:
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Imnaviat Flume ==
Install a new larger solar panel and battery

== Toolik SR50 snow sensor test site ==

*Install SR50 test site
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

== Toolik Geonor T200B precip gauge site prep ==

* select site location
** need 120VAC power
* install concrete base block
** dig hole for about 6CF concrete
** prepare template for 4 bolts, 225cm apart
** mix and place concrete
** set bolts in place; orient N-S and E-W, leave 6" above surface
** protect from elements etc. until set
* sensor to be installed later...

Sept 2008 Field Trip - Emily and Ken

2008-08-28T21:37:39Z

137.229.71.46:

This is a to do list written by Emily and Ken detailing work to be done on the Sept 4-11 field trip.
Helicopter is available approximately Sept 5-7 and we extended it until we are finished (8-10).
We will visit West Kuparuk and Bullen/Foothills sites, along with Put River, Imnaviat Basin, Upper Kuparuk for stream gaging.

''Ken add stations that need conduit and bear fencing.''

[[NSF Sites Notes from Bob]] Emily and Rob can take care of these problems on the trip up to Prudhoe.

'''Note:''' Sites are grouped by area.

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area)==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4:
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Imnaviat Flume ==
Install a new larger solar panel and battery

== Toolik SR50 snow sensor test site ==

*Install SR50 test site
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

== Toolik Geonor T200B precip gauge site prep ==

* select site location
** need 120VAC power
* install concrete base block
** dig hole for about 6CF concrete
** prepare template for 4 bolts, 225cm apart
** mix and place concrete
** set bolts in place; orient N-S and E-W, leave 6" above surface
** protect from elements etc. until set
* sensor to be installed later...

Sept 2008 Field Trip - Emily and Ken

2008-08-28T21:36:51Z

137.229.71.46:

This is a to do list written by Emily and Ken detailing work to be done on the Sept 4-11 field trip.
Helicopter is available approximately Sept 5-7 and we extended it until we are finished (8-10).
We will visit West Kuparuk and Bullen/Foothills sites, along with Put River, Imnaviat Basin, Upper Kuparuk for stream gaging.

''Ken add stations that need conduit and bear fencing.''

[[NSF Sites Notes from Bob]]

'''Note:''' Sites are grouped by area.

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area)==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4:
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Imnaviat Flume ==
Install a new larger solar panel and battery

== Toolik SR50 snow sensor test site ==

*Install SR50 test site
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

== Toolik Geonor T200B precip gauge site prep ==

* select site location
** need 120VAC power
* install concrete base block
** dig hole for about 6CF concrete
** prepare template for 4 bolts, 225cm apart
** mix and place concrete
** set bolts in place; orient N-S and E-W, leave 6" above surface
** protect from elements etc. until set
* sensor to be installed later...

Sept 2008 Field Trip - Emily and Ken

2008-08-28T00:36:28Z

137.229.71.46: /* Day 1 & 2 West of Dalton Highway (White Hills Area) */

''Ken add stations that need conduit and bear fencing.''

[[NSF Sites Notes from Bob]]

'''Note:''' Sites are grouped by area.

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area)==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4:
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Bring spare cable and spare anemometer. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Imnaviat Flume ==
Install a new larger solar panel and battery

== Toolik SR50 snow sensor test site ==

*Install SR50 test site
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

== Toolik Geonor T200B precip gauge site prep ==

* select site location
** need 120VAC power
* install concrete base block
** dig hole for about 6CF concrete
** prepare template for 4 bolts, 225cm apart
** mix and place concrete
** set bolts in place; orient N-S and E-W, leave 6" above surface
** protect from elements etc. until set
* sensor to be installed later...

Sept 2008 Field Trip - Emily and Ken

2008-08-28T00:35:33Z

137.229.71.46: /* Toolik SR50 snow sensor test site */

''Ken add stations that need conduit and bear fencing.''

[[NSF Sites Notes from Bob]]

'''Note:''' Sites are grouped by area.

== Day 0, after drive to Toolik ==
1. [[SagRiverDOT]]:
* Troubleshoot network at base station

== Day 1 & 2 West of Dalton Highway (White Hills Area)==
1. [[West Kuparuk met]]:
* Troubleshoot station
* Install SR50
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

2. [[dfm4| DFM4 NW Kuparuk Met]] DFM4:
* '''Add Electric Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

3. [[dfm2| DFM2 White Hills met]]:
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* '''Check or Replace Anemometer'''. Wind speed/direction are 0 since 7/17.
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

4. [[dfm3| DFM3 North White Hills Met]]
* Add bark chips
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* trim vegetation

5. [[dfm1| DFM1 South White Hills Met]]
* '''Replace SR50.''' Measure old distance to ground and then measure new dist. after installation.
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 3 (Bullen Area/Kavik Area) ==

6. [[dbm7| DBM7 Kadleroshilik Met]]:
* '''Check (or replace) net radiometer''' - readings went bad after we left the site
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

7. [[dbm8| DBM8 Bullen Met]] DBM8
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

8. [[dbm4| DBM4 Sag-Ivi Met]] DBM4:
* '''Add E-Fence'''
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

9. [[dbm5| DBM5 Upper Kad Met]] DBM5:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area
* '''Add E-Fence???'''

10. [[dbm6| DBM6 Kavik Met]]:
* Add bark chips, trim vegetation
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Day 4 & 5 (Mountain Sites) ==

11. [[dbr2| DBR2 Ribdon Repeater]] DBR2 Troubleshooting
* Needs HMP45C
* Needs YSIx3
* Add conduit

12. [[dbm3| DBM3 Juniper Met]] DBM3
* North fence needs another post,
* solar panel wires are exposed, needs "plates" or other protection
* install conduit
* Swap HMP45C
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

13. [[dbm1| DBM1 Accomplishment Cr Met]]
* Swap HMP45C
* install conduit if time permits
* install solar panel plate (larger size)
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

14. [[dbm2| DBM2 Ribdon Cr Met]] DBM2
* Swap HMP45C
* install conduit
* Add bark chips, trim vegetation (if needed)
* Measure distance from ground to snow sensor
* Take photos of site and snow sensor area

== Imnaviat Flume ==
Install a new larger solar panel and battery

== Toolik SR50 snow sensor test site ==

*Install SR50 test site
**SR50's, wood chips, etc.
**Mounting equipment
**datalogger
**hmp45c/anememometer?
**wood chips
**Battery, solar panel, charge controller ?
**radio/antennae?

== Toolik Geonor T200B precip gauge site prep ==

* select site location
** need 120VAC power
* install concrete base block
** dig hole for about 6CF concrete
** prepare template for 4 bolts, 225cm apart
** mix and place concrete
** set bolts in place; orient N-S and E-W, leave 6" above surface
** protect from elements etc. until set
* sensor to be installed later...