http://ocotal.iarc.uaf.edu/api.php?action=feedcontributions&feedformat=atom&user=137.229.91.133&* 2026-05-12T22:48:02Z User contributions MediaWiki 1.34.2 http://ocotal.iarc.uaf.edu/index.php?title=Spring_2016_site_visit&diff=2400 2016-06-10T23:09:46Z

<p>137.229.91.133: /* install new evap pan */</p> <hr /> <div><br /> Head up June 7th, 2016<br /> ==install new evap pan==<br /> *leak test (marine epoxy in case of leaks. should be up in the EDC office)<br /> *clean out bottom<br /> *float should hang from the right side of the sprocket wheel with the counter-weight to the left side of the wheel. A white line is painted on the front of the sprocket, When viewed from the front side, the line should be at the 11 o’clock or 30° when the float is resting on the bottom of the<br /> gauge.<br /> *field calibrate<br /> <br /> Fill pan partway with water, measure height with ruler in mm<br /> Measure voltage by reading the EvapLevelTemp variable on the program<br /> Add more water, measure water depth in pan<br /> Measure voltage<br /> Calculate multiplier and offset using y = mx+b<br /> m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> b(offset) = height1-(m*voltage1)<br /> <br /> ==calibrate precip==<br /> Tipping bucket<br /> *fill bottle to line, use smallest orifice, do this 3 times<br /> *should be 30mm per bottle, so 90mm total<br /> *change multiplier in program if necessary <br /> <br /> Pluvio accuracy test<br /> *received software in ftp from ott (on my fancy laptop, need to transfer to toughbook)<br /> *need usb cable<br /> <br /> ==Brie Helps with==<br /> *swap in fancier wind sensor 5108-45-12M<br /> ::shouldn't need to re-align if don't move he orientation ring<br /> ::wiring slightly different<br /> *swap out HMP155s<br /> **write down which height is which SN<br /> *download garden cam images<br /> ** bring replacement batteries<br /> ** to turn off: press and hold organge power button until 3 beeps and green LED turns off<br /> ** remove drive, download and clear images on computer<br /> ** to turn on:press and hold organge power button until green LED lights up. after a few sec beep twice. green LED every 15 sec indicates normal running. if any other beeping or lights, consult manual<br /> <br /> ==additional tasks==<br /> *wire junction to split all instruments needing 12V from logger<br /> *swap out quantum sensors<br /> **bring mini wrench to replace them<br /> **&lt;s&gt;figure out what the connection is like at toolik&lt;/s&gt;<br /> **&lt;s&gt;change calibration constant?&lt;/s&gt;<br /> *remove old radio<br /> *get field books from Brie<br /> *swap CNR4, change program constants<br /> *install new barometer, change program constants<br /> *level radiometers + tipping bucket<br /> *Take down auxiliary snow station<br /> **get data off of logger, wind up power and ethernet, etc<br /> <br /> == take photos of sensors without pics on instrumentation site==<br /> *HMP155<br /> *wind sensors<br /> *snow dept<br /> *barometer<br /> *evap pan<br /> <br /> ==program changes==<br /> *evap pan calibration<br /> *possible tipping bucket calibration<br /> *possible pluvio calibration<br /> *&lt;s&gt;UVA+UVB corrections. UVA:0.0221, UVB: 0.00178 (per Lija's email)<br /> *barometer mult and offset changes (+85 to offset for elevation difference)<br /> *CNR4 constants<br /> ::LW up: 7.51<br /> ::LW down: 8.24<br /> ::SW up: 16.77<br /> ::SW down: 14.82<br /> *5108 WS multiplier, 0.1666&lt;/s&gt;<br /> *we zero out the CMP6, but not the CNR4. reconsider?<br /> <br /> ==get SN of all instruments/loggers on google sheet==<br /> *datalogger,mux, radios, nl__<br /> *both wind sensors,cmp4, cmp6, evap gauge, precips<br /> *basically everything<br /> <br /> ==To change on instrumentation website==<br /> * pluvio is actually version 2<br /> * lake temp measurement<br /> * barometer<br /> * ask ed to put 2015 met report up<br /> <br /> ==to bring==<br /> *laptop + charger<br /> *field laptop + charger<br /> *tipping bucket calibration box<br /> *gloves, hat(warm and sun)<br /> *tools (level, compass, small wrench for quantum) <br /> *wire junction<br /> *hiking boots,rubber boots,running shoes<br /> *field book, regular notebook<br /> *usb cable for pluvio<br /> *batteries for garden cam<br /> *measuring cup set for leveling UVA and UVB sensors<br /> *cookies for brie<br /> *instruments<br /> **anemometer<br /> **CNR4<br /> **Two HMP155s<br /> **baromter<br /> **quantum<br /> <br /> ==to purchase==<br /> *action packers<br /> *AA batteries<br /> *scrubby for the evaporation pan<br /> <br /> ==should have had==<br /> *electrical tape<br /> *snips<br /> *crimper (where did it go?)<br /> *rectangle level<br /> *larger crescent wrench<br /> *zip ties<br /> *2 crossarm mounting kits for wind sensors<br /> *teflon tape<br /> *tape for pulling wire through conduit<br /> *spare wire<br /> *spare campbell flathead<br /> *lense cloth for radiometer<br /> <br /> ==accomplished==<br /> June 8, 2016<br /> *swapped both HMP155<br /> *swapped 5108 for 5106. the crossarm had rotated. brie re-levelled it and secured it with better crossarm mounting bracket (need to purchase another). and consider moving the bar next time we swap a sensor.<br /> *downloaded garden cam images, cleared flashdrive, replaced upper batteries, need to replace lower ones.<br /> *emptied pluvio<br /> **pluvio software WORKS when connected to pluvio! calibrate tomorrow<br /> <br /> June 9, 2016<br /> *swapped quantum<br /> *swapped CNR4<br /> *Calibrated tipping bucket<br /> ::read 81.27 mm for 3 bottles instead of 90. =&gt; multiplied multiplier by 1.107. new multiplier = 0.281<br /> *swapped barometer<br /> *rewired 12V and G into wire junction so easier to wire<br /> *re-wired new wind sensor<br /> *replaced garden cam batteries<br /> <br /> ==Tomorrow==<br /> *blue mesh/tarp for pluvio?<br /> *find a weight for the pluvio<br /> *aspirated AT? brie suggested https://www.campbellsci.com/pn43502<br /> <br /> ==post trip==<br /> *calibrate swapped sensors<br /> *troubleshoot wind speed and air temp jumps<br /> *update website and spreadsheet with SN and calibration swap dates<br /> *think about pressure<br /> *mesh for pluvio</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Spring_2016_site_visit&diff=2399 2016-06-10T19:35:41Z

<p>137.229.91.133: /* should have had */</p> <hr /> <div><br /> Head up June 7th, 2016<br /> ==install new evap pan==<br /> *leak test (marine epoxy in case of leaks. should be up in the EDC office)<br /> *clean out bottom<br /> *field calibrate<br /> <br /> Fill pan partway with water, measure height with ruler in mm<br /> Measure voltage by reading the EvapLevelTemp variable on the program<br /> Add more water, measure water depth in pan<br /> Measure voltage<br /> Calculate multiplier and offset using y = mx+b<br /> m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> b(offset) = height1-(m*voltage1)<br /> <br /> ==calibrate precip==<br /> Tipping bucket<br /> *fill bottle to line, use smallest orifice, do this 3 times<br /> *should be 30mm per bottle, so 90mm total<br /> *change multiplier in program if necessary <br /> <br /> Pluvio accuracy test<br /> *received software in ftp from ott (on my fancy laptop, need to transfer to toughbook)<br /> *need usb cable<br /> <br /> ==Brie Helps with==<br /> *swap in fancier wind sensor 5108-45-12M<br /> ::shouldn't need to re-align if don't move he orientation ring<br /> ::wiring slightly different<br /> *swap out HMP155s<br /> **write down which height is which SN<br /> *download garden cam images<br /> ** bring replacement batteries<br /> ** to turn off: press and hold organge power button until 3 beeps and green LED turns off<br /> ** remove drive, download and clear images on computer<br /> ** to turn on:press and hold organge power button until green LED lights up. after a few sec beep twice. green LED every 15 sec indicates normal running. if any other beeping or lights, consult manual<br /> <br /> ==additional tasks==<br /> *wire junction to split all instruments needing 12V from logger<br /> *swap out quantum sensors<br /> **bring mini wrench to replace them<br /> **&lt;s&gt;figure out what the connection is like at toolik&lt;/s&gt;<br /> **&lt;s&gt;change calibration constant?&lt;/s&gt;<br /> *remove old radio<br /> *get field books from Brie<br /> *swap CNR4, change program constants<br /> *install new barometer, change program constants<br /> *level radiometers + tipping bucket<br /> *Take down auxiliary snow station<br /> **get data off of logger, wind up power and ethernet, etc<br /> <br /> == take photos of sensors without pics on instrumentation site==<br /> *HMP155<br /> *wind sensors<br /> *snow dept<br /> *barometer<br /> *evap pan<br /> <br /> ==program changes==<br /> *evap pan calibration<br /> *possible tipping bucket calibration<br /> *possible pluvio calibration<br /> *&lt;s&gt;UVA+UVB corrections. UVA:0.0221, UVB: 0.00178 (per Lija's email)<br /> *barometer mult and offset changes (+85 to offset for elevation difference)<br /> *CNR4 constants<br /> ::LW up: 7.51<br /> ::LW down: 8.24<br /> ::SW up: 16.77<br /> ::SW down: 14.82<br /> *5108 WS multiplier, 0.1666&lt;/s&gt;<br /> *we zero out the CMP6, but not the CNR4. reconsider?<br /> <br /> ==get SN of all instruments/loggers on google sheet==<br /> *datalogger,mux, radios, nl__<br /> *both wind sensors,cmp4, cmp6, evap gauge, precips<br /> *basically everything<br /> <br /> ==To change on instrumentation website==<br /> * pluvio is actually version 2<br /> * lake temp measurement<br /> * barometer<br /> * ask ed to put 2015 met report up<br /> <br /> ==to bring==<br /> *laptop + charger<br /> *field laptop + charger<br /> *tipping bucket calibration box<br /> *gloves, hat(warm and sun)<br /> *tools (level, compass, small wrench for quantum) <br /> *wire junction<br /> *hiking boots,rubber boots,running shoes<br /> *field book, regular notebook<br /> *usb cable for pluvio<br /> *batteries for garden cam<br /> *measuring cup set for leveling UVA and UVB sensors<br /> *cookies for brie<br /> *instruments<br /> **anemometer<br /> **CNR4<br /> **Two HMP155s<br /> **baromter<br /> **quantum<br /> <br /> ==to purchase==<br /> *action packers<br /> *AA batteries<br /> *scrubby for the evaporation pan<br /> <br /> ==should have had==<br /> *electrical tape<br /> *snips<br /> *crimper (where did it go?)<br /> *rectangle level<br /> *larger crescent wrench<br /> *zip ties<br /> *2 crossarm mounting kits for wind sensors<br /> *teflon tape<br /> *tape for pulling wire through conduit<br /> *spare wire<br /> *spare campbell flathead<br /> *lense cloth for radiometer<br /> <br /> ==accomplished==<br /> June 8, 2016<br /> *swapped both HMP155<br /> *swapped 5108 for 5106. the crossarm had rotated. brie re-levelled it and secured it with better crossarm mounting bracket (need to purchase another). and consider moving the bar next time we swap a sensor.<br /> *downloaded garden cam images, cleared flashdrive, replaced upper batteries, need to replace lower ones.<br /> *emptied pluvio<br /> **pluvio software WORKS when connected to pluvio! calibrate tomorrow<br /> <br /> June 9, 2016<br /> *swapped quantum<br /> *swapped CNR4<br /> *Calibrated tipping bucket<br /> ::read 81.27 mm for 3 bottles instead of 90. =&gt; multiplied multiplier by 1.107. new multiplier = 0.281<br /> *swapped barometer<br /> *rewired 12V and G into wire junction so easier to wire<br /> *re-wired new wind sensor<br /> *replaced garden cam batteries<br /> <br /> ==Tomorrow==<br /> *blue mesh/tarp for pluvio?<br /> *find a weight for the pluvio<br /> *aspirated AT? brie suggested https://www.campbellsci.com/pn43502<br /> <br /> ==post trip==<br /> *calibrate swapped sensors<br /> *troubleshoot wind speed and air temp jumps<br /> *update website and spreadsheet with SN and calibration swap dates<br /> *think about pressure<br /> *mesh for pluvio</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Summer_2016_visit&diff=2647 2016-06-10T19:34:28Z

<p>137.229.91.133: </p> <hr /> <div>*get tower safety trained<br /> *CANOE out to figure all of underwater sensors out!<br /> **inspect pressure transducer and change desiccant<br /> **figure out what is measuring temperature<br /> **swap underwater quantum<br /> *replace snow transducer<br /> *remove old radio antenna<br /> *bring longer conduit housing for evap pan<br /> *mesh for pluvio</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Summer_2016_visit&diff=2646 2016-06-10T19:34:06Z

<p>137.229.91.133: </p> <hr /> <div>*get tower safety trained<br /> *CANOE out to figure all of underwater sensors out!<br /> **inspect pressure transducer and change desiccant<br /> **figure out what is measuring temperature<br /> **swap underwater quantum<br /> *replace snow transducer<br /> *remove old radio antenna<br /> *bring longer conduit housing for evap pan</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Spring_2016_site_visit&diff=2398 2016-06-10T18:02:52Z

<p>137.229.91.133: /* accomplished */</p> <hr /> <div><br /> Head up June 7th, 2016<br /> ==install new evap pan==<br /> *leak test (marine epoxy in case of leaks. should be up in the EDC office)<br /> *clean out bottom<br /> *field calibrate<br /> <br /> Fill pan partway with water, measure height with ruler in mm<br /> Measure voltage by reading the EvapLevelTemp variable on the program<br /> Add more water, measure water depth in pan<br /> Measure voltage<br /> Calculate multiplier and offset using y = mx+b<br /> m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> b(offset) = height1-(m*voltage1)<br /> <br /> ==calibrate precip==<br /> Tipping bucket<br /> *fill bottle to line, use smallest orifice, do this 3 times<br /> *should be 30mm per bottle, so 90mm total<br /> *change multiplier in program if necessary <br /> <br /> Pluvio accuracy test<br /> *received software in ftp from ott (on my fancy laptop, need to transfer to toughbook)<br /> *need usb cable<br /> <br /> ==Brie Helps with==<br /> *swap in fancier wind sensor 5108-45-12M<br /> ::shouldn't need to re-align if don't move he orientation ring<br /> ::wiring slightly different<br /> *swap out HMP155s<br /> **write down which height is which SN<br /> *download garden cam images<br /> ** bring replacement batteries<br /> ** to turn off: press and hold organge power button until 3 beeps and green LED turns off<br /> ** remove drive, download and clear images on computer<br /> ** to turn on:press and hold organge power button until green LED lights up. after a few sec beep twice. green LED every 15 sec indicates normal running. if any other beeping or lights, consult manual<br /> <br /> ==additional tasks==<br /> *wire junction to split all instruments needing 12V from logger<br /> *swap out quantum sensors<br /> **bring mini wrench to replace them<br /> **&lt;s&gt;figure out what the connection is like at toolik&lt;/s&gt;<br /> **&lt;s&gt;change calibration constant?&lt;/s&gt;<br /> *remove old radio<br /> *get field books from Brie<br /> *swap CNR4, change program constants<br /> *install new barometer, change program constants<br /> *level radiometers + tipping bucket<br /> *Take down auxiliary snow station<br /> **get data off of logger, wind up power and ethernet, etc<br /> <br /> == take photos of sensors without pics on instrumentation site==<br /> *HMP155<br /> *wind sensors<br /> *snow dept<br /> *barometer<br /> *evap pan<br /> <br /> ==program changes==<br /> *evap pan calibration<br /> *possible tipping bucket calibration<br /> *possible pluvio calibration<br /> *&lt;s&gt;UVA+UVB corrections. UVA:0.0221, UVB: 0.00178 (per Lija's email)<br /> *barometer mult and offset changes (+85 to offset for elevation difference)<br /> *CNR4 constants<br /> ::LW up: 7.51<br /> ::LW down: 8.24<br /> ::SW up: 16.77<br /> ::SW down: 14.82<br /> *5108 WS multiplier, 0.1666&lt;/s&gt;<br /> *we zero out the CMP6, but not the CNR4. reconsider?<br /> <br /> ==get SN of all instruments/loggers on google sheet==<br /> *datalogger,mux, radios, nl__<br /> *both wind sensors,cmp4, cmp6, evap gauge, precips<br /> *basically everything<br /> <br /> ==To change on instrumentation website==<br /> * pluvio is actually version 2<br /> * lake temp measurement<br /> * barometer<br /> * ask ed to put 2015 met report up<br /> <br /> ==to bring==<br /> *laptop + charger<br /> *field laptop + charger<br /> *tipping bucket calibration box<br /> *gloves, hat(warm and sun)<br /> *tools (level, compass, small wrench for quantum) <br /> *wire junction<br /> *hiking boots,rubber boots,running shoes<br /> *field book, regular notebook<br /> *usb cable for pluvio<br /> *batteries for garden cam<br /> *measuring cup set for leveling UVA and UVB sensors<br /> *cookies for brie<br /> *instruments<br /> **anemometer<br /> **CNR4<br /> **Two HMP155s<br /> **baromter<br /> **quantum<br /> <br /> ==to purchase==<br /> *action packers<br /> *AA batteries<br /> *scrubby for the evaporation pan<br /> <br /> ==should have had==<br /> *electrical tape<br /> *snips<br /> *crimper (where did it go?)<br /> *rectangle level<br /> *larger crescent wrench<br /> *zip ties<br /> *2 crossarm mounting kits for wind sensors<br /> *mesh for shield for pluvio<br /> <br /> ==accomplished==<br /> June 8, 2016<br /> *swapped both HMP155<br /> *swapped 5108 for 5106. the crossarm had rotated. brie re-levelled it and secured it with better crossarm mounting bracket (need to purchase another). and consider moving the bar next time we swap a sensor.<br /> *downloaded garden cam images, cleared flashdrive, replaced upper batteries, need to replace lower ones.<br /> *emptied pluvio<br /> **pluvio software WORKS when connected to pluvio! calibrate tomorrow<br /> <br /> June 9, 2016<br /> *swapped quantum<br /> *swapped CNR4<br /> *Calibrated tipping bucket<br /> ::read 81.27 mm for 3 bottles instead of 90. =&gt; multiplied multiplier by 1.107. new multiplier = 0.281<br /> *swapped barometer<br /> *rewired 12V and G into wire junction so easier to wire<br /> *re-wired new wind sensor<br /> *replaced garden cam batteries<br /> <br /> ==Tomorrow==<br /> *blue mesh/tarp for pluvio?<br /> *find a weight for the pluvio<br /> *aspirated AT? brie suggested https://www.campbellsci.com/pn43502<br /> <br /> ==post trip==<br /> *calibrate swapped sensors<br /> *troubleshoot wind speed and air temp jumps<br /> *update website and spreadsheet with SN and calibration swap dates<br /> *think about pressure<br /> *mesh for pluvio</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Spring_2016_site_visit&diff=2397 2016-06-10T17:58:51Z

<p>137.229.91.133: /* accomplished */</p> <hr /> <div><br /> Head up June 7th, 2016<br /> ==install new evap pan==<br /> *leak test (marine epoxy in case of leaks. should be up in the EDC office)<br /> *clean out bottom<br /> *field calibrate<br /> <br /> Fill pan partway with water, measure height with ruler in mm<br /> Measure voltage by reading the EvapLevelTemp variable on the program<br /> Add more water, measure water depth in pan<br /> Measure voltage<br /> Calculate multiplier and offset using y = mx+b<br /> m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> b(offset) = height1-(m*voltage1)<br /> <br /> ==calibrate precip==<br /> Tipping bucket<br /> *fill bottle to line, use smallest orifice, do this 3 times<br /> *should be 30mm per bottle, so 90mm total<br /> *change multiplier in program if necessary <br /> <br /> Pluvio accuracy test<br /> *received software in ftp from ott (on my fancy laptop, need to transfer to toughbook)<br /> *need usb cable<br /> <br /> ==Brie Helps with==<br /> *swap in fancier wind sensor 5108-45-12M<br /> ::shouldn't need to re-align if don't move he orientation ring<br /> ::wiring slightly different<br /> *swap out HMP155s<br /> **write down which height is which SN<br /> *download garden cam images<br /> ** bring replacement batteries<br /> ** to turn off: press and hold organge power button until 3 beeps and green LED turns off<br /> ** remove drive, download and clear images on computer<br /> ** to turn on:press and hold organge power button until green LED lights up. after a few sec beep twice. green LED every 15 sec indicates normal running. if any other beeping or lights, consult manual<br /> <br /> ==additional tasks==<br /> *wire junction to split all instruments needing 12V from logger<br /> *swap out quantum sensors<br /> **bring mini wrench to replace them<br /> **&lt;s&gt;figure out what the connection is like at toolik&lt;/s&gt;<br /> **&lt;s&gt;change calibration constant?&lt;/s&gt;<br /> *remove old radio<br /> *get field books from Brie<br /> *swap CNR4, change program constants<br /> *install new barometer, change program constants<br /> *level radiometers + tipping bucket<br /> *Take down auxiliary snow station<br /> **get data off of logger, wind up power and ethernet, etc<br /> <br /> == take photos of sensors without pics on instrumentation site==<br /> *HMP155<br /> *wind sensors<br /> *snow dept<br /> *barometer<br /> *evap pan<br /> <br /> ==program changes==<br /> *evap pan calibration<br /> *possible tipping bucket calibration<br /> *possible pluvio calibration<br /> *&lt;s&gt;UVA+UVB corrections. UVA:0.0221, UVB: 0.00178 (per Lija's email)<br /> *barometer mult and offset changes (+85 to offset for elevation difference)<br /> *CNR4 constants<br /> ::LW up: 7.51<br /> ::LW down: 8.24<br /> ::SW up: 16.77<br /> ::SW down: 14.82<br /> *5108 WS multiplier, 0.1666&lt;/s&gt;<br /> *we zero out the CMP6, but not the CNR4. reconsider?<br /> <br /> ==get SN of all instruments/loggers on google sheet==<br /> *datalogger,mux, radios, nl__<br /> *both wind sensors,cmp4, cmp6, evap gauge, precips<br /> *basically everything<br /> <br /> ==To change on instrumentation website==<br /> * pluvio is actually version 2<br /> * lake temp measurement<br /> * barometer<br /> * ask ed to put 2015 met report up<br /> <br /> ==to bring==<br /> *laptop + charger<br /> *field laptop + charger<br /> *tipping bucket calibration box<br /> *gloves, hat(warm and sun)<br /> *tools (level, compass, small wrench for quantum) <br /> *wire junction<br /> *hiking boots,rubber boots,running shoes<br /> *field book, regular notebook<br /> *usb cable for pluvio<br /> *batteries for garden cam<br /> *measuring cup set for leveling UVA and UVB sensors<br /> *cookies for brie<br /> *instruments<br /> **anemometer<br /> **CNR4<br /> **Two HMP155s<br /> **baromter<br /> **quantum<br /> <br /> ==to purchase==<br /> *action packers<br /> *AA batteries<br /> *scrubby for the evaporation pan<br /> <br /> ==should have had==<br /> *electrical tape<br /> *snips<br /> *crimper (where did it go?)<br /> *rectangle level<br /> *larger crescent wrench<br /> *zip ties<br /> *2 crossarm mounting kits for wind sensors<br /> *mesh for shield for pluvio<br /> <br /> ==accomplished==<br /> June 8, 2016<br /> *swapped both HMP155<br /> *swapped 5108 for 5106. the crossarm had rotated. brie re-levelled it and secured it with better crossarm mounting bracket (need to purchase another). and consider moving the bar next time we swap a sensor.<br /> *downloaded garden cam images, cleared flashdrive, replaced upper batteries, need to replace lower ones.<br /> *emptied pluvio<br /> **pluvio software WORKS when connected to pluvio! calibrate tomorrow<br /> <br /> June 9, 2016<br /> *swapped quantum<br /> *swapped CNR4<br /> *Calibrated tipping bucket<br /> ::read 81.27 mm for 3 bottles instead of 90. worth changing?<br /> *swapped barometer<br /> *rewired 12V and G into wire junction so easier to wire<br /> *re-wired new wind sensor<br /> *replaced garden cam batteries<br /> <br /> ==Tomorrow==<br /> *blue mesh/tarp for pluvio?<br /> *find a weight for the pluvio<br /> *aspirated AT? brie suggested https://www.campbellsci.com/pn43502<br /> <br /> ==post trip==<br /> *calibrate swapped sensors<br /> *troubleshoot wind speed and air temp jumps<br /> *update website and spreadsheet with SN and calibration swap dates<br /> *think about pressure<br /> *mesh for pluvio</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Spring_2016_site_visit&diff=2396 2016-06-10T17:44:09Z

<p>137.229.91.133: /* post trip */</p> <hr /> <div><br /> Head up June 7th, 2016<br /> ==install new evap pan==<br /> *leak test (marine epoxy in case of leaks. should be up in the EDC office)<br /> *clean out bottom<br /> *field calibrate<br /> <br /> Fill pan partway with water, measure height with ruler in mm<br /> Measure voltage by reading the EvapLevelTemp variable on the program<br /> Add more water, measure water depth in pan<br /> Measure voltage<br /> Calculate multiplier and offset using y = mx+b<br /> m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> b(offset) = height1-(m*voltage1)<br /> <br /> ==calibrate precip==<br /> Tipping bucket<br /> *fill bottle to line, use smallest orifice, do this 3 times<br /> *should be 30mm per bottle, so 90mm total<br /> *change multiplier in program if necessary <br /> <br /> Pluvio accuracy test<br /> *received software in ftp from ott (on my fancy laptop, need to transfer to toughbook)<br /> *need usb cable<br /> <br /> ==Brie Helps with==<br /> *swap in fancier wind sensor 5108-45-12M<br /> ::shouldn't need to re-align if don't move he orientation ring<br /> ::wiring slightly different<br /> *swap out HMP155s<br /> **write down which height is which SN<br /> *download garden cam images<br /> ** bring replacement batteries<br /> ** to turn off: press and hold organge power button until 3 beeps and green LED turns off<br /> ** remove drive, download and clear images on computer<br /> ** to turn on:press and hold organge power button until green LED lights up. after a few sec beep twice. green LED every 15 sec indicates normal running. if any other beeping or lights, consult manual<br /> <br /> ==additional tasks==<br /> *wire junction to split all instruments needing 12V from logger<br /> *swap out quantum sensors<br /> **bring mini wrench to replace them<br /> **&lt;s&gt;figure out what the connection is like at toolik&lt;/s&gt;<br /> **&lt;s&gt;change calibration constant?&lt;/s&gt;<br /> *remove old radio<br /> *get field books from Brie<br /> *swap CNR4, change program constants<br /> *install new barometer, change program constants<br /> *level radiometers + tipping bucket<br /> *Take down auxiliary snow station<br /> **get data off of logger, wind up power and ethernet, etc<br /> <br /> == take photos of sensors without pics on instrumentation site==<br /> *HMP155<br /> *wind sensors<br /> *snow dept<br /> *barometer<br /> *evap pan<br /> <br /> ==program changes==<br /> *evap pan calibration<br /> *possible tipping bucket calibration<br /> *possible pluvio calibration<br /> *&lt;s&gt;UVA+UVB corrections. UVA:0.0221, UVB: 0.00178 (per Lija's email)<br /> *barometer mult and offset changes (+85 to offset for elevation difference)<br /> *CNR4 constants<br /> ::LW up: 7.51<br /> ::LW down: 8.24<br /> ::SW up: 16.77<br /> ::SW down: 14.82<br /> *5108 WS multiplier, 0.1666&lt;/s&gt;<br /> *we zero out the CMP6, but not the CNR4. reconsider?<br /> <br /> ==get SN of all instruments/loggers on google sheet==<br /> *datalogger,mux, radios, nl__<br /> *both wind sensors,cmp4, cmp6, evap gauge, precips<br /> *basically everything<br /> <br /> ==To change on instrumentation website==<br /> * pluvio is actually version 2<br /> * lake temp measurement<br /> * barometer<br /> * ask ed to put 2015 met report up<br /> <br /> ==to bring==<br /> *laptop + charger<br /> *field laptop + charger<br /> *tipping bucket calibration box<br /> *gloves, hat(warm and sun)<br /> *tools (level, compass, small wrench for quantum) <br /> *wire junction<br /> *hiking boots,rubber boots,running shoes<br /> *field book, regular notebook<br /> *usb cable for pluvio<br /> *batteries for garden cam<br /> *measuring cup set for leveling UVA and UVB sensors<br /> *cookies for brie<br /> *instruments<br /> **anemometer<br /> **CNR4<br /> **Two HMP155s<br /> **baromter<br /> **quantum<br /> <br /> ==to purchase==<br /> *action packers<br /> *AA batteries<br /> *scrubby for the evaporation pan<br /> <br /> ==should have had==<br /> *electrical tape<br /> *snips<br /> *crimper (where did it go?)<br /> *rectangle level<br /> *larger crescent wrench<br /> *zip ties<br /> *2 crossarm mounting kits for wind sensors<br /> *mesh for shield for pluvio<br /> <br /> ==accomplished==<br /> June 6, 2016<br /> *swapped both HMP155<br /> *swapped 5108 for 5106. the crossarm had rotated. brie re-levelled it and secured it with better crossarm mounting bracket (need to purchase another). and consider moving the bar next time we swap a sensor.<br /> *downloaded garden cam images, cleared flashdrive, replaced upper batteries, need to replace lower ones.<br /> *emptied pluvio<br /> **pluvio software WORKS when connected to pluvio! calibrate tomorrow<br /> <br /> ==Tomorrow==<br /> *blue mesh/tarp for pluvio?<br /> *find a weight for the pluvio<br /> *aspirated AT? brie suggested https://www.campbellsci.com/pn43502<br /> <br /> ==post trip==<br /> *calibrate swapped sensors<br /> *troubleshoot wind speed and air temp jumps<br /> *update website and spreadsheet with SN and calibration swap dates<br /> *think about pressure<br /> *mesh for pluvio</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Spring_2016_site_visit&diff=2395 2016-06-10T17:15:42Z

<p>137.229.91.133: /* post trip */</p> <hr /> <div><br /> Head up June 7th, 2016<br /> ==install new evap pan==<br /> *leak test (marine epoxy in case of leaks. should be up in the EDC office)<br /> *clean out bottom<br /> *field calibrate<br /> <br /> Fill pan partway with water, measure height with ruler in mm<br /> Measure voltage by reading the EvapLevelTemp variable on the program<br /> Add more water, measure water depth in pan<br /> Measure voltage<br /> Calculate multiplier and offset using y = mx+b<br /> m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> b(offset) = height1-(m*voltage1)<br /> <br /> ==calibrate precip==<br /> Tipping bucket<br /> *fill bottle to line, use smallest orifice, do this 3 times<br /> *should be 30mm per bottle, so 90mm total<br /> *change multiplier in program if necessary <br /> <br /> Pluvio accuracy test<br /> *received software in ftp from ott (on my fancy laptop, need to transfer to toughbook)<br /> *need usb cable<br /> <br /> ==Brie Helps with==<br /> *swap in fancier wind sensor 5108-45-12M<br /> ::shouldn't need to re-align if don't move he orientation ring<br /> ::wiring slightly different<br /> *swap out HMP155s<br /> **write down which height is which SN<br /> *download garden cam images<br /> ** bring replacement batteries<br /> ** to turn off: press and hold organge power button until 3 beeps and green LED turns off<br /> ** remove drive, download and clear images on computer<br /> ** to turn on:press and hold organge power button until green LED lights up. after a few sec beep twice. green LED every 15 sec indicates normal running. if any other beeping or lights, consult manual<br /> <br /> ==additional tasks==<br /> *wire junction to split all instruments needing 12V from logger<br /> *swap out quantum sensors<br /> **bring mini wrench to replace them<br /> **&lt;s&gt;figure out what the connection is like at toolik&lt;/s&gt;<br /> **&lt;s&gt;change calibration constant?&lt;/s&gt;<br /> *remove old radio<br /> *get field books from Brie<br /> *swap CNR4, change program constants<br /> *install new barometer, change program constants<br /> *level radiometers + tipping bucket<br /> *Take down auxiliary snow station<br /> **get data off of logger, wind up power and ethernet, etc<br /> <br /> == take photos of sensors without pics on instrumentation site==<br /> *HMP155<br /> *wind sensors<br /> *snow dept<br /> *barometer<br /> *evap pan<br /> <br /> ==program changes==<br /> *evap pan calibration<br /> *possible tipping bucket calibration<br /> *possible pluvio calibration<br /> *&lt;s&gt;UVA+UVB corrections. UVA:0.0221, UVB: 0.00178 (per Lija's email)<br /> *barometer mult and offset changes (+85 to offset for elevation difference)<br /> *CNR4 constants<br /> ::LW up: 7.51<br /> ::LW down: 8.24<br /> ::SW up: 16.77<br /> ::SW down: 14.82<br /> *5108 WS multiplier, 0.1666&lt;/s&gt;<br /> *we zero out the CMP6, but not the CNR4. reconsider?<br /> <br /> ==get SN of all instruments/loggers on google sheet==<br /> *datalogger,mux, radios, nl__<br /> *both wind sensors,cmp4, cmp6, evap gauge, precips<br /> *basically everything<br /> <br /> ==To change on instrumentation website==<br /> * pluvio is actually version 2<br /> * lake temp measurement<br /> * barometer<br /> * ask ed to put 2015 met report up<br /> <br /> ==to bring==<br /> *laptop + charger<br /> *field laptop + charger<br /> *tipping bucket calibration box<br /> *gloves, hat(warm and sun)<br /> *tools (level, compass, small wrench for quantum) <br /> *wire junction<br /> *hiking boots,rubber boots,running shoes<br /> *field book, regular notebook<br /> *usb cable for pluvio<br /> *batteries for garden cam<br /> *measuring cup set for leveling UVA and UVB sensors<br /> *cookies for brie<br /> *instruments<br /> **anemometer<br /> **CNR4<br /> **Two HMP155s<br /> **baromter<br /> **quantum<br /> <br /> ==to purchase==<br /> *action packers<br /> *AA batteries<br /> *scrubby for the evaporation pan<br /> <br /> ==should have had==<br /> *electrical tape<br /> *snips<br /> *crimper (where did it go?)<br /> *rectangle level<br /> *larger crescent wrench<br /> *zip ties<br /> *2 crossarm mounting kits for wind sensors<br /> *mesh for shield for pluvio<br /> <br /> ==accomplished==<br /> June 6, 2016<br /> *swapped both HMP155<br /> *swapped 5108 for 5106. the crossarm had rotated. brie re-levelled it and secured it with better crossarm mounting bracket (need to purchase another). and consider moving the bar next time we swap a sensor.<br /> *downloaded garden cam images, cleared flashdrive, replaced upper batteries, need to replace lower ones.<br /> *emptied pluvio<br /> **pluvio software WORKS when connected to pluvio! calibrate tomorrow<br /> <br /> ==Tomorrow==<br /> *blue mesh/tarp for pluvio?<br /> *find a weight for the pluvio<br /> *aspirated AT? brie suggested https://www.campbellsci.com/pn43502<br /> <br /> ==post trip==<br /> *calibrate swapped sensors<br /> *troubleshoot wind speed and air temp jumps<br /> *update website and spreadsheet with SN and calibration swap dates<br /> *think about pressure</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Spring_2016_site_visit&diff=2394 2016-06-10T00:00:45Z

<p>137.229.91.133: </p> <hr /> <div><br /> Head up June 7th, 2016<br /> ==install new evap pan==<br /> *leak test (marine epoxy in case of leaks. should be up in the EDC office)<br /> *clean out bottom<br /> *field calibrate<br /> <br /> Fill pan partway with water, measure height with ruler in mm<br /> Measure voltage by reading the EvapLevelTemp variable on the program<br /> Add more water, measure water depth in pan<br /> Measure voltage<br /> Calculate multiplier and offset using y = mx+b<br /> m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> b(offset) = height1-(m*voltage1)<br /> <br /> ==calibrate precip==<br /> Tipping bucket<br /> *fill bottle to line, use smallest orifice, do this 3 times<br /> *should be 30mm per bottle, so 90mm total<br /> *change multiplier in program if necessary <br /> <br /> Pluvio accuracy test<br /> *received software in ftp from ott (on my fancy laptop, need to transfer to toughbook)<br /> *need usb cable<br /> <br /> ==Brie Helps with==<br /> *swap in fancier wind sensor 5108-45-12M<br /> ::shouldn't need to re-align if don't move he orientation ring<br /> ::wiring slightly different<br /> *swap out HMP155s<br /> **write down which height is which SN<br /> *download garden cam images<br /> ** bring replacement batteries<br /> ** to turn off: press and hold organge power button until 3 beeps and green LED turns off<br /> ** remove drive, download and clear images on computer<br /> ** to turn on:press and hold organge power button until green LED lights up. after a few sec beep twice. green LED every 15 sec indicates normal running. if any other beeping or lights, consult manual<br /> <br /> ==additional tasks==<br /> *wire junction to split all instruments needing 12V from logger<br /> *swap out quantum sensors<br /> **bring mini wrench to replace them<br /> **&lt;s&gt;figure out what the connection is like at toolik&lt;/s&gt;<br /> **&lt;s&gt;change calibration constant?&lt;/s&gt;<br /> *remove old radio<br /> *get field books from Brie<br /> *swap CNR4, change program constants<br /> *install new barometer, change program constants<br /> *level radiometers + tipping bucket<br /> *Take down auxiliary snow station<br /> **get data off of logger, wind up power and ethernet, etc<br /> <br /> == take photos of sensors without pics on instrumentation site==<br /> *HMP155<br /> *wind sensors<br /> *snow dept<br /> *barometer<br /> *evap pan<br /> <br /> ==program changes==<br /> *evap pan calibration<br /> *possible tipping bucket calibration<br /> *possible pluvio calibration<br /> *&lt;s&gt;UVA+UVB corrections. UVA:0.0221, UVB: 0.00178 (per Lija's email)<br /> *barometer mult and offset changes (+85 to offset for elevation difference)<br /> *CNR4 constants<br /> ::LW up: 7.51<br /> ::LW down: 8.24<br /> ::SW up: 16.77<br /> ::SW down: 14.82<br /> *5108 WS multiplier, 0.1666&lt;/s&gt;<br /> *we zero out the CMP6, but not the CNR4. reconsider?<br /> <br /> ==get SN of all instruments/loggers on google sheet==<br /> *datalogger,mux, radios, nl__<br /> *both wind sensors,cmp4, cmp6, evap gauge, precips<br /> *basically everything<br /> <br /> ==To change on instrumentation website==<br /> * pluvio is actually version 2<br /> * lake temp measurement<br /> * barometer<br /> * ask ed to put 2015 met report up<br /> <br /> ==to bring==<br /> *laptop + charger<br /> *field laptop + charger<br /> *tipping bucket calibration box<br /> *gloves, hat(warm and sun)<br /> *tools (level, compass, small wrench for quantum) <br /> *wire junction<br /> *hiking boots,rubber boots,running shoes<br /> *field book, regular notebook<br /> *usb cable for pluvio<br /> *batteries for garden cam<br /> *measuring cup set for leveling UVA and UVB sensors<br /> *cookies for brie<br /> *instruments<br /> **anemometer<br /> **CNR4<br /> **Two HMP155s<br /> **baromter<br /> **quantum<br /> <br /> ==to purchase==<br /> *action packers<br /> *AA batteries<br /> *scrubby for the evaporation pan<br /> <br /> ==should have had==<br /> *electrical tape<br /> *snips<br /> *crimper (where did it go?)<br /> *rectangle level<br /> *larger crescent wrench<br /> *zip ties<br /> *2 crossarm mounting kits for wind sensors<br /> *mesh for shield for pluvio<br /> <br /> ==accomplished==<br /> June 6, 2016<br /> *swapped both HMP155<br /> *swapped 5108 for 5106. the crossarm had rotated. brie re-levelled it and secured it with better crossarm mounting bracket (need to purchase another). and consider moving the bar next time we swap a sensor.<br /> *downloaded garden cam images, cleared flashdrive, replaced upper batteries, need to replace lower ones.<br /> *emptied pluvio<br /> **pluvio software WORKS when connected to pluvio! calibrate tomorrow<br /> <br /> ==Tomorrow==<br /> *blue mesh/tarp for pluvio?<br /> *find a weight for the pluvio<br /> *aspirated AT? brie suggested https://www.campbellsci.com/pn43502<br /> <br /> ==post trip==<br /> *calibrate swapped sensors<br /> *troubleshoot wind speed and air temp jumps<br /> *update website and spreadsheet with SN and calibration swap dates</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Summer_2016_visit&diff=2645 2016-06-09T23:54:08Z

<p>137.229.91.133: </p> <hr /> <div>*get tower safety trained<br /> *CANOE out to figure all of underwater sensors out!<br /> **inspect pressure transducer and change desiccant<br /> **figure out what is measuring temperature<br /> **swap underwater quantum<br /> *replace snow transducer<br /> *remove old radio antenna</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Spring_2016_site_visit&diff=2393 2016-06-09T19:35:01Z

<p>137.229.91.133: /* Tomorrow */</p> <hr /> <div><br /> Head up June 7th, 2016<br /> ==install new evap pan==<br /> *leak test (marine epoxy in case of leaks. should be up in the EDC office)<br /> *clean out bottom<br /> *field calibrate<br /> <br /> Fill pan partway with water, measure height with ruler in mm<br /> Measure voltage by reading the EvapLevelTemp variable on the program<br /> Add more water, measure water depth in pan<br /> Measure voltage<br /> Calculate multiplier and offset using y = mx+b<br /> m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> b(offset) = height1-(m*voltage1)<br /> <br /> ==calibrate precip==<br /> Tipping bucket<br /> *fill bottle to line, use smallest orifice, do this 3 times<br /> *should be 30mm per bottle, so 90mm total<br /> *change multiplier in program if necessary <br /> <br /> Pluvio accuracy test<br /> *received software in ftp from ott (on my fancy laptop, need to transfer to toughbook)<br /> *need usb cable<br /> <br /> ==Brie Helps with==<br /> *swap in fancier wind sensor 5108-45-12M<br /> ::shouldn't need to re-align if don't move he orientation ring<br /> ::wiring slightly different<br /> *swap out HMP155s<br /> **write down which height is which SN<br /> *download garden cam images<br /> ** bring replacement batteries<br /> ** to turn off: press and hold organge power button until 3 beeps and green LED turns off<br /> ** remove drive, download and clear images on computer<br /> ** to turn on:press and hold organge power button until green LED lights up. after a few sec beep twice. green LED every 15 sec indicates normal running. if any other beeping or lights, consult manual<br /> <br /> ==additional tasks==<br /> *wire junction to split all instruments needing 12V from logger<br /> *swap out quantum sensors<br /> **bring mini wrench to replace them<br /> **&lt;s&gt;figure out what the connection is like at toolik&lt;/s&gt;<br /> **&lt;s&gt;change calibration constant?&lt;/s&gt;<br /> *remove old radio<br /> *get field books from Brie<br /> *swap CNR4, change program constants<br /> *install new barometer, change program constants<br /> *level radiometers + tipping bucket<br /> *Take down auxiliary snow station<br /> **get data off of logger, wind up power and ethernet, etc<br /> <br /> == take photos of sensors without pics on instrumentation site==<br /> *HMP155<br /> *wind sensors<br /> *snow dept<br /> *barometer<br /> *evap pan<br /> <br /> ==program changes==<br /> *evap pan calibration<br /> *possible tipping bucket calibration<br /> *possible pluvio calibration<br /> *&lt;s&gt;UVA+UVB corrections. UVA:0.0221, UVB: 0.00178 (per Lija's email)<br /> *barometer mult and offset changes (+85 to offset for elevation difference)<br /> *CNR4 constants<br /> ::LW up: 7.51<br /> ::LW down: 8.24<br /> ::SW up: 16.77<br /> ::SW down: 14.82<br /> *5108 WS multiplier, 0.1666&lt;/s&gt;<br /> *we zero out the CMP6, but not the CNR4. reconsider?<br /> <br /> ==get SN of all instruments/loggers on google sheet==<br /> *datalogger,mux, radios, nl__<br /> *both wind sensors,cmp4, cmp6, evap gauge, precips<br /> *basically everything<br /> <br /> ==To change on instrumentation website==<br /> * pluvio is actually version 2<br /> * lake temp measurement<br /> * barometer<br /> * ask ed to put 2015 met report up<br /> <br /> ==to bring==<br /> *laptop + charger<br /> *field laptop + charger<br /> *tipping bucket calibration box<br /> *gloves, hat(warm and sun)<br /> *tools (level, compass, small wrench for quantum) <br /> *wire junction<br /> *hiking boots,rubber boots,running shoes<br /> *field book, regular notebook<br /> *usb cable for pluvio<br /> *batteries for garden cam<br /> *measuring cup set for leveling UVA and UVB sensors<br /> *cookies for brie<br /> *instruments<br /> **anemometer<br /> **CNR4<br /> **Two HMP155s<br /> **baromter<br /> **quantum<br /> <br /> ==to purchase==<br /> *action packers<br /> *AA batteries<br /> *scrubby for the evaporation pan<br /> <br /> ==should have had==<br /> *electrical tape<br /> *snips<br /> *crimper (where did it go?)<br /> *rectangle level<br /> *larger crescent wrench<br /> *zip ties<br /> *2 crossarm mounting kits for wind sensors<br /> *mesh for shield for pluvio<br /> <br /> ==accomplished==<br /> June 6, 2016<br /> *swapped both HMP155<br /> *swapped 5108 for 5106. the crossarm had rotated. brie re-levelled it and secured it with better crossarm mounting bracket (need to purchase another). and consider moving the bar next time we swap a sensor.<br /> *downloaded garden cam images, cleared flashdrive, replaced upper batteries, need to replace lower ones.<br /> *emptied pluvio<br /> **pluvio software WORKS when connected to pluvio! calibrate tomorrow<br /> <br /> ==Tomorrow==<br /> *blue mesh/tarp for pluvio?<br /> *find a weight for the pluvio<br /> *aspirated AT? brie suggested https://www.campbellsci.com/pn43502</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Spring_2016_site_visit&diff=2392 2016-06-09T17:36:33Z

<p>137.229.91.133: /* Brie Helps with */</p> <hr /> <div><br /> Head up June 7th, 2016<br /> ==install new evap pan==<br /> *leak test (marine epoxy in case of leaks. should be up in the EDC office)<br /> *clean out bottom<br /> *field calibrate<br /> <br /> Fill pan partway with water, measure height with ruler in mm<br /> Measure voltage by reading the EvapLevelTemp variable on the program<br /> Add more water, measure water depth in pan<br /> Measure voltage<br /> Calculate multiplier and offset using y = mx+b<br /> m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> b(offset) = height1-(m*voltage1)<br /> <br /> ==calibrate precip==<br /> Tipping bucket<br /> *fill bottle to line, use smallest orifice, do this 3 times<br /> *should be 30mm per bottle, so 90mm total<br /> *change multiplier in program if necessary <br /> <br /> Pluvio accuracy test<br /> *received software in ftp from ott (on my fancy laptop, need to transfer to toughbook)<br /> *need usb cable<br /> <br /> ==Brie Helps with==<br /> *swap in fancier wind sensor 5108-45-12M<br /> ::shouldn't need to re-align if don't move he orientation ring<br /> ::wiring slightly different<br /> *swap out HMP155s<br /> **write down which height is which SN<br /> *download garden cam images<br /> ** bring replacement batteries<br /> ** to turn off: press and hold organge power button until 3 beeps and green LED turns off<br /> ** remove drive, download and clear images on computer<br /> ** to turn on:press and hold organge power button until green LED lights up. after a few sec beep twice. green LED every 15 sec indicates normal running. if any other beeping or lights, consult manual<br /> <br /> ==additional tasks==<br /> *wire junction to split all instruments needing 12V from logger<br /> *swap out quantum sensors<br /> **bring mini wrench to replace them<br /> **&lt;s&gt;figure out what the connection is like at toolik&lt;/s&gt;<br /> **&lt;s&gt;change calibration constant?&lt;/s&gt;<br /> *remove old radio<br /> *get field books from Brie<br /> *swap CNR4, change program constants<br /> *install new barometer, change program constants<br /> *level radiometers + tipping bucket<br /> *Take down auxiliary snow station<br /> **get data off of logger, wind up power and ethernet, etc<br /> <br /> == take photos of sensors without pics on instrumentation site==<br /> *HMP155<br /> *wind sensors<br /> *snow dept<br /> *barometer<br /> *evap pan<br /> <br /> ==program changes==<br /> *evap pan calibration<br /> *possible tipping bucket calibration<br /> *possible pluvio calibration<br /> *&lt;s&gt;UVA+UVB corrections. UVA:0.0221, UVB: 0.00178 (per Lija's email)<br /> *barometer mult and offset changes (+85 to offset for elevation difference)<br /> *CNR4 constants<br /> ::LW up: 7.51<br /> ::LW down: 8.24<br /> ::SW up: 16.77<br /> ::SW down: 14.82<br /> *5108 WS multiplier, 0.1666&lt;/s&gt;<br /> *we zero out the CMP6, but not the CNR4. reconsider?<br /> <br /> ==get SN of all instruments/loggers on google sheet==<br /> *datalogger,mux, radios, nl__<br /> *both wind sensors,cmp4, cmp6, evap gauge, precips<br /> *basically everything<br /> <br /> ==To change on instrumentation website==<br /> * pluvio is actually version 2<br /> * lake temp measurement<br /> * barometer<br /> * ask ed to put 2015 met report up<br /> <br /> ==to bring==<br /> *laptop + charger<br /> *field laptop + charger<br /> *tipping bucket calibration box<br /> *gloves, hat(warm and sun)<br /> *tools (level, compass, small wrench for quantum) <br /> *wire junction<br /> *hiking boots,rubber boots,running shoes<br /> *field book, regular notebook<br /> *usb cable for pluvio<br /> *batteries for garden cam<br /> *measuring cup set for leveling UVA and UVB sensors<br /> *cookies for brie<br /> *instruments<br /> **anemometer<br /> **CNR4<br /> **Two HMP155s<br /> **baromter<br /> **quantum<br /> <br /> ==to purchase==<br /> *action packers<br /> *AA batteries<br /> *scrubby for the evaporation pan<br /> <br /> ==should have had==<br /> *electrical tape<br /> *snips<br /> *crimper (where did it go?)<br /> *rectangle level<br /> *larger crescent wrench<br /> *zip ties<br /> *2 crossarm mounting kits for wind sensors<br /> *mesh for shield for pluvio<br /> <br /> ==accomplished==<br /> June 6, 2016<br /> *swapped both HMP155<br /> *swapped 5108 for 5106. the crossarm had rotated. brie re-levelled it and secured it with better crossarm mounting bracket (need to purchase another). and consider moving the bar next time we swap a sensor.<br /> *downloaded garden cam images, cleared flashdrive, replaced upper batteries, need to replace lower ones.<br /> *emptied pluvio<br /> **pluvio software WORKS when connected to pluvio! calibrate tomorrow<br /> <br /> ==Tomorrow==<br /> *blue mesh/tarp for pluvio?<br /> *find a weight for the pluvio<br /> *aspirated AT? brie suggested</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Spring_2016_site_visit&diff=2391 2016-06-09T17:35:47Z

<p>137.229.91.133: /* program changes */</p> <hr /> <div><br /> Head up June 7th, 2016<br /> ==install new evap pan==<br /> *leak test (marine epoxy in case of leaks. should be up in the EDC office)<br /> *clean out bottom<br /> *field calibrate<br /> <br /> Fill pan partway with water, measure height with ruler in mm<br /> Measure voltage by reading the EvapLevelTemp variable on the program<br /> Add more water, measure water depth in pan<br /> Measure voltage<br /> Calculate multiplier and offset using y = mx+b<br /> m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> b(offset) = height1-(m*voltage1)<br /> <br /> ==calibrate precip==<br /> Tipping bucket<br /> *fill bottle to line, use smallest orifice, do this 3 times<br /> *should be 30mm per bottle, so 90mm total<br /> *change multiplier in program if necessary <br /> <br /> Pluvio accuracy test<br /> *received software in ftp from ott (on my fancy laptop, need to transfer to toughbook)<br /> *need usb cable<br /> <br /> ==Brie Helps with==<br /> *swap in fancier wind sensor 5108-45-12M<br /> ::shouldn't need to re-align if don't move he orientation ring<br /> *swap out HMP155s<br /> **write down which height is which SN<br /> *download garden cam images<br /> ** bring replacement batteries<br /> ** to turn off: press and hold organge power button until 3 beeps and green LED turns off<br /> ** remove drive, download and clear images on computer<br /> ** to turn on:press and hold organge power button until green LED lights up. after a few sec beep twice. green LED every 15 sec indicates normal running. if any other beeping or lights, consult manual<br /> <br /> ==additional tasks==<br /> *wire junction to split all instruments needing 12V from logger<br /> *swap out quantum sensors<br /> **bring mini wrench to replace them<br /> **&lt;s&gt;figure out what the connection is like at toolik&lt;/s&gt;<br /> **&lt;s&gt;change calibration constant?&lt;/s&gt;<br /> *remove old radio<br /> *get field books from Brie<br /> *swap CNR4, change program constants<br /> *install new barometer, change program constants<br /> *level radiometers + tipping bucket<br /> *Take down auxiliary snow station<br /> **get data off of logger, wind up power and ethernet, etc<br /> <br /> == take photos of sensors without pics on instrumentation site==<br /> *HMP155<br /> *wind sensors<br /> *snow dept<br /> *barometer<br /> *evap pan<br /> <br /> ==program changes==<br /> *evap pan calibration<br /> *possible tipping bucket calibration<br /> *possible pluvio calibration<br /> *&lt;s&gt;UVA+UVB corrections. UVA:0.0221, UVB: 0.00178 (per Lija's email)<br /> *barometer mult and offset changes (+85 to offset for elevation difference)<br /> *CNR4 constants<br /> ::LW up: 7.51<br /> ::LW down: 8.24<br /> ::SW up: 16.77<br /> ::SW down: 14.82<br /> *5108 WS multiplier, 0.1666&lt;/s&gt;<br /> *we zero out the CMP6, but not the CNR4. reconsider?<br /> <br /> ==get SN of all instruments/loggers on google sheet==<br /> *datalogger,mux, radios, nl__<br /> *both wind sensors,cmp4, cmp6, evap gauge, precips<br /> *basically everything<br /> <br /> ==To change on instrumentation website==<br /> * pluvio is actually version 2<br /> * lake temp measurement<br /> * barometer<br /> * ask ed to put 2015 met report up<br /> <br /> ==to bring==<br /> *laptop + charger<br /> *field laptop + charger<br /> *tipping bucket calibration box<br /> *gloves, hat(warm and sun)<br /> *tools (level, compass, small wrench for quantum) <br /> *wire junction<br /> *hiking boots,rubber boots,running shoes<br /> *field book, regular notebook<br /> *usb cable for pluvio<br /> *batteries for garden cam<br /> *measuring cup set for leveling UVA and UVB sensors<br /> *cookies for brie<br /> *instruments<br /> **anemometer<br /> **CNR4<br /> **Two HMP155s<br /> **baromter<br /> **quantum<br /> <br /> ==to purchase==<br /> *action packers<br /> *AA batteries<br /> *scrubby for the evaporation pan<br /> <br /> ==should have had==<br /> *electrical tape<br /> *snips<br /> *crimper (where did it go?)<br /> *rectangle level<br /> *larger crescent wrench<br /> *zip ties<br /> *2 crossarm mounting kits for wind sensors<br /> *mesh for shield for pluvio<br /> <br /> ==accomplished==<br /> June 6, 2016<br /> *swapped both HMP155<br /> *swapped 5108 for 5106. the crossarm had rotated. brie re-levelled it and secured it with better crossarm mounting bracket (need to purchase another). and consider moving the bar next time we swap a sensor.<br /> *downloaded garden cam images, cleared flashdrive, replaced upper batteries, need to replace lower ones.<br /> *emptied pluvio<br /> **pluvio software WORKS when connected to pluvio! calibrate tomorrow<br /> <br /> ==Tomorrow==<br /> *blue mesh/tarp for pluvio?<br /> *find a weight for the pluvio<br /> *aspirated AT? brie suggested</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Spring_2016_site_visit&diff=2390 2016-06-09T17:14:02Z

<p>137.229.91.133: /* Tomorrow */</p> <hr /> <div><br /> Head up June 7th, 2016<br /> ==install new evap pan==<br /> *leak test (marine epoxy in case of leaks. should be up in the EDC office)<br /> *clean out bottom<br /> *field calibrate<br /> <br /> Fill pan partway with water, measure height with ruler in mm<br /> Measure voltage by reading the EvapLevelTemp variable on the program<br /> Add more water, measure water depth in pan<br /> Measure voltage<br /> Calculate multiplier and offset using y = mx+b<br /> m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> b(offset) = height1-(m*voltage1)<br /> <br /> ==calibrate precip==<br /> Tipping bucket<br /> *fill bottle to line, use smallest orifice, do this 3 times<br /> *should be 30mm per bottle, so 90mm total<br /> *change multiplier in program if necessary <br /> <br /> Pluvio accuracy test<br /> *received software in ftp from ott (on my fancy laptop, need to transfer to toughbook)<br /> *need usb cable<br /> <br /> ==Brie Helps with==<br /> *swap in fancier wind sensor 5108-45-12M<br /> ::shouldn't need to re-align if don't move he orientation ring<br /> *swap out HMP155s<br /> **write down which height is which SN<br /> *download garden cam images<br /> ** bring replacement batteries<br /> ** to turn off: press and hold organge power button until 3 beeps and green LED turns off<br /> ** remove drive, download and clear images on computer<br /> ** to turn on:press and hold organge power button until green LED lights up. after a few sec beep twice. green LED every 15 sec indicates normal running. if any other beeping or lights, consult manual<br /> <br /> ==additional tasks==<br /> *wire junction to split all instruments needing 12V from logger<br /> *swap out quantum sensors<br /> **bring mini wrench to replace them<br /> **&lt;s&gt;figure out what the connection is like at toolik&lt;/s&gt;<br /> **&lt;s&gt;change calibration constant?&lt;/s&gt;<br /> *remove old radio<br /> *get field books from Brie<br /> *swap CNR4, change program constants<br /> *install new barometer, change program constants<br /> *level radiometers + tipping bucket<br /> *Take down auxiliary snow station<br /> **get data off of logger, wind up power and ethernet, etc<br /> <br /> == take photos of sensors without pics on instrumentation site==<br /> *HMP155<br /> *wind sensors<br /> *snow dept<br /> *barometer<br /> *evap pan<br /> <br /> ==program changes==<br /> *evap pan calibration<br /> *possible tipping bucket calibration<br /> *possible pluvio calibration<br /> *&lt;s&gt;UVA+UVB corrections. UVA:0.0221, UVB: 0.00178 (per Lija's email)<br /> *barometer mult and offset changes (+85 to offset for elevation difference)<br /> *CNR4 constants<br /> ::LW up: 7.51<br /> ::LW down: 8.24<br /> ::SW up: 16.77<br /> ::SW down: 14.82&lt;/s&gt;<br /> *we zero out the CMP6, but not the CNR4. reconsider?<br /> <br /> ==get SN of all instruments/loggers on google sheet==<br /> *datalogger,mux, radios, nl__<br /> *both wind sensors,cmp4, cmp6, evap gauge, precips<br /> *basically everything<br /> <br /> ==To change on instrumentation website==<br /> * pluvio is actually version 2<br /> * lake temp measurement<br /> * barometer<br /> * ask ed to put 2015 met report up<br /> <br /> ==to bring==<br /> *laptop + charger<br /> *field laptop + charger<br /> *tipping bucket calibration box<br /> *gloves, hat(warm and sun)<br /> *tools (level, compass, small wrench for quantum) <br /> *wire junction<br /> *hiking boots,rubber boots,running shoes<br /> *field book, regular notebook<br /> *usb cable for pluvio<br /> *batteries for garden cam<br /> *measuring cup set for leveling UVA and UVB sensors<br /> *cookies for brie<br /> *instruments<br /> **anemometer<br /> **CNR4<br /> **Two HMP155s<br /> **baromter<br /> **quantum<br /> <br /> ==to purchase==<br /> *action packers<br /> *AA batteries<br /> *scrubby for the evaporation pan<br /> <br /> ==should have had==<br /> *electrical tape<br /> *snips<br /> *crimper (where did it go?)<br /> *rectangle level<br /> *larger crescent wrench<br /> *zip ties<br /> *2 crossarm mounting kits for wind sensors<br /> *mesh for shield for pluvio<br /> <br /> ==accomplished==<br /> June 6, 2016<br /> *swapped both HMP155<br /> *swapped 5108 for 5106. the crossarm had rotated. brie re-levelled it and secured it with better crossarm mounting bracket (need to purchase another). and consider moving the bar next time we swap a sensor.<br /> *downloaded garden cam images, cleared flashdrive, replaced upper batteries, need to replace lower ones.<br /> *emptied pluvio<br /> **pluvio software WORKS when connected to pluvio! calibrate tomorrow<br /> <br /> ==Tomorrow==<br /> *blue mesh/tarp for pluvio?<br /> *find a weight for the pluvio<br /> *aspirated AT? brie suggested</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Spring_2016_site_visit&diff=2388 2016-06-08T22:03:15Z

<p>137.229.91.133: /* should have had */</p> <hr /> <div><br /> Head up June 7th, 2016<br /> ==install new evap pan==<br /> *leak test (marine epoxy in case of leaks. should be up in the EDC office)<br /> *clean out bottom<br /> *field calibrate<br /> <br /> Fill pan partway with water, measure height with ruler in mm<br /> Measure voltage by reading the EvapLevelTemp variable on the program<br /> Add more water, measure water depth in pan<br /> Measure voltage<br /> Calculate multiplier and offset using y = mx+b<br /> m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> b(offset) = height1-(m*voltage1)<br /> <br /> ==calibrate precip==<br /> Tipping bucket<br /> *fill bottle to line, use smallest orifice, do this 3 times<br /> *should be 30mm per bottle, so 90mm total<br /> *change multiplier in program if necessary <br /> <br /> Pluvio accuracy test<br /> *received software in ftp from ott (on my fancy laptop, need to transfer to toughbook)<br /> *need usb cable<br /> <br /> ==Brie Helps with==<br /> *swap in fancier wind sensor 5108-45-12M<br /> ::shouldn't need to re-align if don't move he orientation ring<br /> *swap out HMP155s<br /> **write down which height is which SN<br /> *download garden cam images<br /> ** bring replacement batteries<br /> ** to turn off: press and hold organge power button until 3 beeps and green LED turns off<br /> ** remove drive, download and clear images on computer<br /> ** to turn on:press and hold organge power button until green LED lights up. after a few sec beep twice. green LED every 15 sec indicates normal running. if any other beeping or lights, consult manual<br /> <br /> ==additional tasks==<br /> *wire junction to split all instruments needing 12V from logger<br /> *swap out quantum sensors<br /> **bring mini wrench to replace them<br /> **&lt;s&gt;figure out what the connection is like at toolik&lt;/s&gt;<br /> **&lt;s&gt;change calibration constant?&lt;/s&gt;<br /> *remove old radio<br /> *get field books from Brie<br /> *swap CNR4, change program constants<br /> *install new barometer, change program constants<br /> *level radiometers + tipping bucket<br /> *Take down auxiliary snow station<br /> **get data off of logger, wind up power and ethernet, etc<br /> <br /> == take photos of sensors without pics on instrumentation site==<br /> *HMP155<br /> *wind sensors<br /> *snow dept<br /> *barometer<br /> *evap pan<br /> <br /> ==program changes==<br /> *evap pan calibration<br /> *possible tipping bucket calibration<br /> *possible pluvio calibration<br /> *&lt;s&gt;UVA+UVB corrections. UVA:0.0221, UVB: 0.00178 (per Lija's email)<br /> *barometer mult and offset changes (+85 to offset for elevation difference)<br /> *CNR4 constants<br /> ::LW up: 7.51<br /> ::LW down: 8.24<br /> ::SW up: 16.77<br /> ::SW down: 14.82&lt;/s&gt;<br /> *we zero out the CMP6, but not the CNR4. reconsider?<br /> <br /> ==get SN of all instruments/loggers on google sheet==<br /> *datalogger,mux, radios, nl__<br /> *both wind sensors,cmp4, cmp6, evap gauge, precips<br /> *basically everything<br /> <br /> ==To change on instrumentation website==<br /> * pluvio is actually version 2<br /> * lake temp measurement<br /> * barometer<br /> * ask ed to put 2015 met report up<br /> <br /> ==to bring==<br /> *laptop + charger<br /> *field laptop + charger<br /> *tipping bucket calibration box<br /> *gloves, hat(warm and sun)<br /> *tools (level, compass, small wrench for quantum) <br /> *wire junction<br /> *hiking boots,rubber boots,running shoes<br /> *field book, regular notebook<br /> *usb cable for pluvio<br /> *batteries for garden cam<br /> *measuring cup set for leveling UVA and UVB sensors<br /> *cookies for brie<br /> *instruments<br /> **anemometer<br /> **CNR4<br /> **Two HMP155s<br /> **baromter<br /> **quantum<br /> <br /> ==to purchase==<br /> *action packers<br /> *AA batteries<br /> *scrubby for the evaporation pan<br /> <br /> ==should have had==<br /> *electrical tape<br /> *snips<br /> *crimper (where did it go?)<br /> *rectangle level<br /> *larger crescent wrench<br /> *zip ties<br /> *2 crossarm mounting kits for wind sensors<br /> *mesh for shield for pluvio</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Spring_2016_site_visit&diff=2387 2016-06-08T22:02:48Z

<p>137.229.91.133: </p> <hr /> <div><br /> Head up June 7th, 2016<br /> ==install new evap pan==<br /> *leak test (marine epoxy in case of leaks. should be up in the EDC office)<br /> *clean out bottom<br /> *field calibrate<br /> <br /> Fill pan partway with water, measure height with ruler in mm<br /> Measure voltage by reading the EvapLevelTemp variable on the program<br /> Add more water, measure water depth in pan<br /> Measure voltage<br /> Calculate multiplier and offset using y = mx+b<br /> m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> b(offset) = height1-(m*voltage1)<br /> <br /> ==calibrate precip==<br /> Tipping bucket<br /> *fill bottle to line, use smallest orifice, do this 3 times<br /> *should be 30mm per bottle, so 90mm total<br /> *change multiplier in program if necessary <br /> <br /> Pluvio accuracy test<br /> *received software in ftp from ott (on my fancy laptop, need to transfer to toughbook)<br /> *need usb cable<br /> <br /> ==Brie Helps with==<br /> *swap in fancier wind sensor 5108-45-12M<br /> ::shouldn't need to re-align if don't move he orientation ring<br /> *swap out HMP155s<br /> **write down which height is which SN<br /> *download garden cam images<br /> ** bring replacement batteries<br /> ** to turn off: press and hold organge power button until 3 beeps and green LED turns off<br /> ** remove drive, download and clear images on computer<br /> ** to turn on:press and hold organge power button until green LED lights up. after a few sec beep twice. green LED every 15 sec indicates normal running. if any other beeping or lights, consult manual<br /> <br /> ==additional tasks==<br /> *wire junction to split all instruments needing 12V from logger<br /> *swap out quantum sensors<br /> **bring mini wrench to replace them<br /> **&lt;s&gt;figure out what the connection is like at toolik&lt;/s&gt;<br /> **&lt;s&gt;change calibration constant?&lt;/s&gt;<br /> *remove old radio<br /> *get field books from Brie<br /> *swap CNR4, change program constants<br /> *install new barometer, change program constants<br /> *level radiometers + tipping bucket<br /> *Take down auxiliary snow station<br /> **get data off of logger, wind up power and ethernet, etc<br /> <br /> == take photos of sensors without pics on instrumentation site==<br /> *HMP155<br /> *wind sensors<br /> *snow dept<br /> *barometer<br /> *evap pan<br /> <br /> ==program changes==<br /> *evap pan calibration<br /> *possible tipping bucket calibration<br /> *possible pluvio calibration<br /> *&lt;s&gt;UVA+UVB corrections. UVA:0.0221, UVB: 0.00178 (per Lija's email)<br /> *barometer mult and offset changes (+85 to offset for elevation difference)<br /> *CNR4 constants<br /> ::LW up: 7.51<br /> ::LW down: 8.24<br /> ::SW up: 16.77<br /> ::SW down: 14.82&lt;/s&gt;<br /> *we zero out the CMP6, but not the CNR4. reconsider?<br /> <br /> ==get SN of all instruments/loggers on google sheet==<br /> *datalogger,mux, radios, nl__<br /> *both wind sensors,cmp4, cmp6, evap gauge, precips<br /> *basically everything<br /> <br /> ==To change on instrumentation website==<br /> * pluvio is actually version 2<br /> * lake temp measurement<br /> * barometer<br /> * ask ed to put 2015 met report up<br /> <br /> ==to bring==<br /> *laptop + charger<br /> *field laptop + charger<br /> *tipping bucket calibration box<br /> *gloves, hat(warm and sun)<br /> *tools (level, compass, small wrench for quantum) <br /> *wire junction<br /> *hiking boots,rubber boots,running shoes<br /> *field book, regular notebook<br /> *usb cable for pluvio<br /> *batteries for garden cam<br /> *measuring cup set for leveling UVA and UVB sensors<br /> *cookies for brie<br /> *instruments<br /> **anemometer<br /> **CNR4<br /> **Two HMP155s<br /> **baromter<br /> **quantum<br /> <br /> ==to purchase==<br /> *action packers<br /> *AA batteries<br /> *scrubby for the evaporation pan<br /> <br /> ==should have had==<br /> *electrical tape<br /> *snips<br /> *crimper (where did it go?)<br /> *rectangle level<br /> *larger crescent wrench<br /> *zip ties<br /> *2 crossarm mounting kits for wind sensors</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=Fall_2015_site_visit&diff=2241 2015-08-24T06:24:13Z

<p>137.229.91.133: </p> <hr /> <div>* replace snow Transducers <br /> * replace therm strings (with?)<br /> * antifreeze in pluvio<br /> * replace desiccants<br /> * clear garden cam of images<br /> * bring longer cable housing for evap pan<br /> * bring electrical splitter for wiring all power to data logger<br /> * put nylock nut on wind sensor nose cap<br /> <br /> done on 8/23 from ~9pm - 10pm<br /> * replaced snow sensor<br /> * leveled quantum par sensor, kip and zonnen radiometer<br /> * emptied pluvio and put ~1L antifreeze in<br /> <br /> todo tomorrow<br /> * level remaining radiometers<br /> * winterize evaporation pan<br /> <br /> Next time<br /> * bring dessicant for radiometers<br /> * how to clean underwater quantum?</div>

137.229.91.133 http://ocotal.iarc.uaf.edu/index.php?title=May_31-_June_6th,_2015_site_visit&diff=2287 2015-06-01T22:50:26Z

<p>137.229.91.133: /* Items to bring up */</p> <hr /> <div>== Instal evap pan ==<br /> *field calibrate<br /> *edit program<br /> *for platform<br /> **exterior grade plywood - home depot will cut it<br /> **exterior deck screws<br /> *calibrate in mm to get units in mm<br /> <br /> == Wind sensors replacement ==<br /> *calculate multiplier for wind direction sensor. for back calculation purposes<br /> *Replace wind direction sensors<br /> *align (declination: 18.5 degrees)<br /> ** North (0/360 degrees) when nose points AWAY from box, for both sensors<br /> **&lt;s&gt;aligned in office so that when nose faces same way as box, reads 180.&lt;/s&gt;<br /> *to install propeller, hand tighten then tighten with channel locks<br /> *both wind sensors can use same excitation port<br /> *White = 5106, Black = 5103<br /> <br /> == Telemetry ==<br /> Finish installing radio + ethernet for redundancy<br /> *old RF310B is in WQ in computer racks to left after enter<br /> **black box with campbell scientific marking<br /> **put timer on power source<br /> *radio connected to CR3000 with CS10 port gets power from this port as well<br /> *check config settings on NL201 nl201.toolik.uaf.edu should be: <br /> **HwAddr: 00:D0:2C:02:0D:73.<br /> **IP address: 137.229.91.81<br /> **Subnet MASK: 255.255.255.192<br /> **Default Gateway/Router:137.229.91.65<br /> <br /> *for NL100 I'm bring up<br /> **HwAddr (MAC address): 00d02c0004c0 <br /> **IP address: 137.229.91.82<br /> **Subnet MASK: 255.255.255.192<br /> **Default Gateway/Router:137.229.91.65<br /> <br /> <br /> == Items to bring up ==<br /> *alcohol swabs<br /> *compass <br /> *outlet timer for old radio<br /> *NL100<br /> *smart phone<br /> *evap gauge <br /> *two RM young wind sensors<br /> *sleeping bag<br /> *nut driver for tower base<br /> *drill + charger<br /> *tube for leveling platform<br /> *wood and screws for platform<br /> *zip ties<br /> *null modem cable for NL100 communication<br /> *cat5 cable and tools for creating connectors<br /> *wire to power NL100 from CR3000 AND ac adapter if outlet space<br /> *field laptop + charger<br /> *laptop + charger<br /> *plywood boards<br /> *field notebook<br /> *camera<br /> *tool bag<br /> *fish tape<br /> *electrical tape<br /> *ethernet-usb plug<br /> *serial-usb plug<br /> *rag<br /> *cable housing<br /> *pertinent manuals<br /> *extension chord<br /> *disc<br /> *printed copies of the plan<br /> *gloves<br /> <br /> == Items to purchase ==<br /> *alcohol swabs<br /> *power strip<br /> *compass<br /> *32 AA batteries for GardenCam<br /> *plywood +screws for base<br /> <br /> == Tipping tower ==<br /> *grab 2 saw horses<br /> *undo one guy wire, loosen others<br /> *undo one leg bolts, loosen others<br /> ** 2 bolts on each leg, take off both on one leg, just loosen bottom screw for other 2 legs<br /> *CAREFUL of sensor wires when lowering tower<br /> *have WD40 with me in case can't get wind sensor screws undone<br /> <br /> when raise tower, make turnbuckles taught but not too tight<br /> <br /> == PLAN ==<br /> <br /> ===Telemetry===<br /> * plug in timer to old radio base<br /> * check config settings on NL201 in CPS shed<br /> * run cat5 line from radio in CPS shed<br /> * leave NL100 in enclosure, wire power from data logger or outlet<br /> *(grab ladder against back of tool shed to look into box)<br /> <br /> ===Wind Sensors + Garden Cam===<br /> *Alignment <br /> **which way does tower tip and how is crossbar oriented <br /> **stake out east west <br /> * Tip Tower<br /> * Reset Garden Cam<br /> **remover flash drive (may need to cut tape for this)<br /> **download pics<br /> **clear drive<br /> *Replace Wind sensors<br /> **use old mounts or change if necessary<br /> **screw on propeller, hand tighten then tighten with channel locks <br /> **alignment ring then sensor <br /> * zip tie wires and pull them into box<br /> * Wire Sensors<br /> ' RM Young 5103 Wind Monitor (black)<br /> <br /> ' Red Wire -- CR3000 P1<br /> <br /> ' Green Wire -- CR3000 SE1<br /> <br /> ' Blue Wire -- CR3000 VX1<br /> <br /> ' Clear Wire -- CR3000 AG<br /> <br /> ' Black Wire -- CR3000 AG<br /> <br /> ' White Wire -- CR3000 AG<br /> <br /> ' RM Young 5106 Wind Monitor(white)<br /> <br /> ' Red Wire -- CR3000 P2<br /> <br /> ' Green Wire -- CR3000 SE2<br /> <br /> ' Blue Wire -- CR3000 VX1<br /> <br /> ' Clear Wire -- CR3000 AG<br /> <br /> ' Black Wire -- CR3000 AG<br /> <br /> ' White Wire -- CR3000 AG<br /> <br /> * Download data files from CR3000<br /> * upload new program<br /> * Align Wind sensors on ground as best as possible<br /> ** first horizontal plane<br /> ** second east-west<br /> * Raise tower<br /> ** have Brie climb it to align sensors if necessary<br /> * Replace batteries in Garden Cam power case<br /> <br /> ===Evaporation Gauge===<br /> *Build platform with pallets and plywood<br /> *attach gauge to pan with pipe<br /> *run wire through housing and into enclosure<br /> **' Evaporation Pan<br /> **' White Wire -- CR3000 SE16<br /> **' Red Wire -- CR3000 VX3 <br /> **' Black Wire -- CR3000 Signal Ground<br /> *Calibrate<br /> ** Fill pan partway with water, measure height with ruler in mm<br /> ** Measure voltage by reading the EvapLevelTemp variable on the program<br /> ** Add more water, measure water depth in pan<br /> ** Measure voltage<br /> ** Calculate multiplier and offset using y = mx+b<br /> ***m(multiplier) = (height1-height2)/(voltage2-voltage1)<br /> ***b(offset) = height1-(m*voltage1)<br /> *Change multiplier and offset in program<br /> **download data<br /> **upload new program<br /> <br /> <br /> === Additional tasks ===<br /> (grab ladder against back of tool shed to look into box)<br /> <br /> *download CR3000 + radio device config settings<br /> *level and alcohol swab radiometer (par) <br /> *level and alcohol swab 3 radiometers on old tower (net Rad, UVA, UVB)<br /> <br /> *Pluvio<br /> **Hole in mesh to craw in, 3 captive screws holding on outer shield<br /> **empty most of water inside plastic inner tub<br /> **remove any dead animals <br /> <br /> *note any damage<br /> *Make sure no water in battery box<br /> *inspect seals where wires go in<br /> *inspect solar panels<br /> <br /> == TODO ==<br /> *&lt;s&gt;TELEMETRY&lt;s&gt;<br /> *&lt;s&gt;PR and purchase stuff&lt;/s&gt;<br /> *&lt;s&gt;update program for evap pan, wind sensors, snow depth quality number&lt;/s&gt;<br /> *&lt;s&gt;program NL100&lt;/s&gt;<br /> *&lt;s&gt;evap gauge base supplies and logistics&lt;/s&gt;<br /> *&lt;s&gt;learn ethernet cable connectors&lt;/s&gt;<br /> *&lt;s&gt;GardenCam (how reset? what does PI want?)&lt;/s&gt;<br /> *&lt;s&gt;figure out where wind sensor go on data logger, and how to mount&lt;/s&gt;<br /> *&lt;s&gt;re-align wind sensor from basement&lt;/s&gt;<br /> *read pluvio manual<br /> *&lt;s&gt;find photo of evap pan base&lt;/s&gt;<br /> *&lt;s&gt;ask toolik for pallets&lt;/s&gt;<br /> *&lt;s&gt;new longer cable for wind sensor&lt;/s&gt;<br /> *&lt;s&gt;instal skype on iphone&lt;/s&gt;<br /> *&lt;s&gt;get wind sensor mounting pole from basement&lt;/s&gt;<br /> *&lt;s&gt;check types of wind instruments&lt;/s&gt;<br /> *&lt;s&gt;write out plan&lt;/s&gt;<br /> *pack<br /> *&lt;s&gt;check how long cable on evap gauge is&lt;/s&gt;</div>

137.229.91.133