IARC 207 Wiki - User contributions [en]

NGEE Barrow 2013 Site Install Trip

2013-05-05T07:00:15Z

209.193.54.74:

==May 2013 Trip==
===Purpose: ===
* Rewire Grid Site station with CR1000 & new multiplexers
* Setup MD485s to get Grid online
* reconfigure Site C CR1000 for act as a pakbus router
* Snow Surveys
* Any other prep that's possible for the June trip
* Bring back shotgun
* slather anticorrosion goo on all 12V/G points?
* Record Thermal Conductivity Heater Resistance using a high-accuracy ohmmeter
* Swap out SR50A

===Shipping===
* None

===To Purchase===
* Anti-Corrosion Goo
* Ziplocs
* In Barrow:
** Butane
* Food?

===Pre-trip to do===
* Read up on CR1000 Pakbus Routing
* Pack

===Stuff to bring===
* Adirondack Tube
* Scale
* Thaw Probe
* Ziplocs
* GPS
* 4 Precision Resistors for new logger
* High Precision Voltmeter
* Duct Seal
* 80' of cable

==== Technical Gear ====
* '''Shotgun''' -- in Barrow already
* Keypads
* '''fish tape'''
* Tool Bags
* Computer & (packed) SC32B
* Climbing harness
* Serial Cables & spares
* Sawzall
* drill

==== Food to bring out ====
* Optional

==== Probable Luggage ====
# Bob Personal Actionpacker [Bob #1]
# Work Actionpacker #1 [Bob #2]

===Rough on-site todo===
# Copy wiring of Grid Site
# Transfer wires to new multiplexer & Logger
# Snowsurveys
# Measure Heater Resistances for all thermal conductivity probes
# Look to see if the C site pit 2 thermal conductivity sensors could be connected to a lower instrument enclosure.
# configure C as pakbus router for grid
## http://www.campbellsci.com/forum/messages.cfm?threadid=6E4ABAA0-81A1-4158-B850230D8A56A2EF
# armor and run rs485 line between C and grid

NGEE Barrow 2013 Site Install Trip

2013-05-05T06:52:42Z

209.193.54.74:

==May 2013 Trip==
===Purpose: ===
* Rewire Grid Site station with CR1000 & new multiplexers
* Setup MD485s to get Grid online
* reconfigure Site C CR1000 for act as a pakbus router
* Snow Surveys
* Any other prep that's possible for the June trip
* Bring back shotgun
* slather anticorrosion goo on all 12V/G points?
* Record Thermal Conductivity Heater Resistance using a high-accuracy ohmmeter
* Swap out SR50A

===Shipping===
* None

===To Purchase===
* Anti-Corrosion Goo
* Ziplocs
* In Barrow:
** Butane
* Food?

===Pre-trip to do===
* Read up on CR1000 Pakbus Routing
* Pack

===Stuff to bring===
* Adirondack Tube
* Scale
* Thaw Probe
* Ziplocs
* GPS
* 4 Precision Resistors for new logger
* High Precision Voltmeter

==== Technical Gear ====
* '''Shotgun''' -- in Barrow already
* Keypads
* '''fish tape'''
* Tool Bags
* Computer & (packed) SC32B
* Climbing harness
* Serial Cables & spares
* Sawzall
* drill

==== Food to bring out ====
* Optional

==== Probable Luggage ====
# Bob Personal Actionpacker [Bob #1]
# Work Actionpacker #1 [Bob #2]

===Rough on-site todo===
# Copy wiring of Grid Site
# Transfer wires to new multiplexer & Logger
# Snowsurveys
# Measure Heater Resistances for all thermal conductivity probes
# Look to see if the C site pit 2 thermal conductivity sensors could be connected to a lower instrument enclosure.
# configure C as pakbus router for grid
## http://www.campbellsci.com/forum/messages.cfm?threadid=6E4ABAA0-81A1-4158-B850230D8A56A2EF
# armor and run rs485 line between C and grid

NGEE Barrow 2013 Site Install Trip

2013-05-04T23:49:26Z

209.193.54.74: /* Purpose: */

==May 2013 Trip==
===Purpose: ===
* Rewire Grid Site station with CR1000 & new multiplexers
* Setup MD485s to get Grid online
* reconfigure Site C CR1000 for act as a pakbus router
* Snow Surveys
* Any other prep that's possible for the June trip
* Bring back shotgun
* slather anticorrosion goo on all 12V/G points?
* Record Thermal Conductivity Heater Resistance using a high-accuracy ohmmeter
* Swap out SR50A

===Shipping===
* None

===To Purchase===
* Anti-Corrosion Goo
* Ziplocs
* In Barrow:
** Butane
* Food?

===Pre-trip to do===
* Read up on CR1000 Pakbus Routing
* Pack

===Stuff to bring===
* Adirondack Tube
* Scale
* Thaw Probe
* Ziplocs
* GPS
* 4 Precision Resistors for new logger
* High Precision Voltmeter

==== Technical Gear ====
* '''Shotgun''' -- in Barrow already
* Keypads
* '''fish tape'''
* Tool Bags
* Computer & (packed) SC32B
* Climbing harness
* Serial Cables & spares
* Sawzall
* drill

==== Food to bring out ====
* Optional

==== Probable Luggage ====
# Bob Personal Actionpacker [Bob #1]
# Work Actionpacker #1 [Bob #2]

====Rough on-site todo====
# Copy wiring of Grid Site
# Transfer wires to new multiplexer & Logger
# Snowsurveys
# Measure Heater Resistances for all thermal conductivity probes
# Look to see if the C site pit 2 thermal conductivity sensors could be connected to a lower instrument enclosure.

NGEE Barrow 2013 Site Install Trip

2013-05-04T23:49:02Z

209.193.54.74:

==May 2013 Trip==
===Purpose: ===
* Rewire Grid Site station with CR1000 & new multiplexers
* Setup MD485s to get Grid online
* reconfigure Site C CR1000 for act as a pakbus router
* Snow Surveys
* Any other prep that's possible for the June trip
* Bring back shotgun
* slather anticorrosion goo on all 12V/G points?
* Record Thermal Conductivity Heater Resistance using a high-accuracy ohmmeter

===Shipping===
* None

===To Purchase===
* Anti-Corrosion Goo
* Ziplocs
* In Barrow:
** Butane
* Food?

===Pre-trip to do===
* Read up on CR1000 Pakbus Routing
* Pack

===Stuff to bring===
* Adirondack Tube
* Scale
* Thaw Probe
* Ziplocs
* GPS
* 4 Precision Resistors for new logger
* High Precision Voltmeter

==== Technical Gear ====
* '''Shotgun''' -- in Barrow already
* Keypads
* '''fish tape'''
* Tool Bags
* Computer & (packed) SC32B
* Climbing harness
* Serial Cables & spares
* Sawzall
* drill

==== Food to bring out ====
* Optional

==== Probable Luggage ====
# Bob Personal Actionpacker [Bob #1]
# Work Actionpacker #1 [Bob #2]

====Rough on-site todo====
# Copy wiring of Grid Site
# Transfer wires to new multiplexer & Logger
# Snowsurveys
# Measure Heater Resistances for all thermal conductivity probes
# Look to see if the C site pit 2 thermal conductivity sensors could be connected to a lower instrument enclosure.

NGEE Barrow 2013 Site Install Trip 2

2013-05-04T23:42:04Z

209.193.54.74:

==June 2013 Trip==

===Shipping===
* New Instrumentation once it arrives on 5/26ish:
** Precip Buckets 3x
** Wind Screen 3x
** HMP155s 6x
** MetOne 5x
** Barometric Pressure
** Radiation Shields
** Cross Arms
*** 1.5" Sched 40 Aluminum = Net Radiometer 3x
*** 1" Sched 40 Aluminum = Upper WS & AT/RH 3x
** Tripod Mast
*** 1.5" Sched 40 Galvanized Pipe
** Net Radiometer
** NuRail Fittings for crossarms

===To Add to each site===
* 2 HMP155s w/ Radiation Shields
* 2 Met One WS
* 1 Tipping Bucket w/ Windscreen
* 1 CNR4 Net Radiometer with Heater/Fan Control
* 1 AM16/32

===Additionally, to add to Site A===
* CS106 Barometric Pressure

===Rewiring at each site===
* Move AM16/32B #1 & #2 RES to CR1000 C1
* Move SR50A Green Wire to CR1000 C5
** Reprogram the IDs for the SR50As
*** #1 = ID7
*** #2 = ID8
*** #3 = ID9
* Also Measure Thermal Conductivity Heater Values

===To Do as of 4/21/2013===
* Modify Programs
* Wiring Diagrams
* PRs for freight
* Sketch up site
* Wire up boxes as much as possible (is anything possible? Maybe just mount the peripherals)
* Review pictures to see if a second box is still needed for just the multiplexer.
* holes in box for instrumentation maybe?
* cut crossarms to length
* Change SDI-12 IDs for SR50As
* Review Site C data... Look closely at SR50A data for precise failure dates.
* SM Grid rewiring?

=== Remaining things to grab===
* ?

===To Purchase===
* ?

===Pre-trip to do===
* Organized per site items ('''X''' means it's packed / shipped)
** Precip Stand (3 sets)
*** 4 NuRail 3/4 offset cross pieces
*** 1 Novalynx Wind Screen
*** 1 TE525m & Cable

** Tripod Related
***
***
****
****
****
****
****
****
****

===Things to buy===
* Bit o' Food?
* ?

===Stuff to bring===

==== things not on a PR yet====

==== Technical Gear ====
* '''Shotgun'''
* Keypads
* '''fish tape'''
* Tool Bags
* Computer & (packed) SC32B
* Climbing harness
* Serial Cables & spares
* Sawzall
* drill

==== Food to bring out ====
* Optional

==== Probable Luggage ====
# Shotgun [Bob #1]
# Bob Personal backpack [Bob #2]
# Work Actionpacker #1 [Bob #3]
#

====Rough on-site todo====
# Remove box & solar panel
# Measure from top of tripod base to cross arm... note in fieldbook
# Remove crossarm off tripod
# unscrew center pole
# put 1.5" offset nurail fitting on new center pole
# attach new center pole
# put cross arm, instrument box, and solar panel back on the tower.
# Install new instrument box on lower leg.
# Mount all new sensors
## Net Radiometer @ 1-1.5m
## WS on radiometer crossarm
## HMP155 on radiometer crossarm
## Second HMP155 & WS high up on tower, maybe as high as they'll reach.
## Armor all the cabling
## Armor and install the precip bucket.
## Install the precip wind screen
# send new program to data logger

NGEE Barrow 2013 Site Install Trip

2013-05-04T22:24:47Z

209.193.54.74:

==May 2013 Trip==
Purpose:
* Rewire Grid Site station with CR1000 & new multiplexers
* Setup MD485s to get Grid online
* reconfigure Site C CR1000 for act as a pakbus router
* Snow Surveys
* Any other prep that's possible for the June trip
* Bring back shotgun
* slather anticorrosion goo on all 12V/G points?

===Shipping===
* None

===To Do as of 4/21/2013===
* Modify Programs
* Wiring Diagrams
* PRs for freight
* Sketch up site
* cut crossarms to length
* Change SDI-12 IDs for SR50As

** Reinforce grounding
* SM Grid rewiring?
*

=== Remaining things to grab===
* ?

===To Purchase===
* ?

===Pre-trip to do===

===Things to buy===
* Bit o' Food?
* ?

===Stuff to bring===
* Adirondack Tube
* Scale
* Thaw Probe
* Ziplocs
* GPS
* 4 Precision Resistors for new logger

==== Technical Gear ====
* '''Shotgun''' -- in Barrow already
* Keypads
* '''fish tape'''
* Tool Bags
* Computer & (packed) SC32B
* Climbing harness
* Serial Cables & spares
* Sawzall
* drill

==== Food to bring out ====
* Optional

==== Probable Luggage ====
# Bob Personal Actionpacker [Bob #1]
# Work Actionpacker #1 [Bob #2]

====Rough on-site todo====
# Copy wiring of Grid Site
# Transfer wires to new multiplexer & Logger
# Snowsurveys

NGEE Barrow 2013 Site Install Trip

2013-05-04T21:31:16Z

209.193.54.74:

==May 2013 Trip==
Purpose:
* Rewire Grid Site station with CR1000 & new multiplexers
* Setup MD485s to get Grid online
* reconfigure Site C CR1000 for act as a pakbus router
* Snow Surveys
* Any other prep that's possible for the June trip
* Bring back shotgun
* slather anticorrosion goo on all 12V/G points?

===Shipping===
* None

===To Do as of 4/21/2013===
* Modify Programs
* Wiring Diagrams
* PRs for freight
* Sketch up site
* cut crossarms to length
* Change SDI-12 IDs for SR50As

** Reinforce grounding
* SM Grid rewiring?
*

=== Remaining things to grab===
* ?

===To Purchase===
* ?

===Pre-trip to do===

===Things to buy===
* Bit o' Food?
* ?

===Stuff to bring===
* Adirondack Tube
* Scale
* Thaw Probe
* Ziplocs
* GPS

==== Technical Gear ====
* '''Shotgun''' -- in Barrow already
* Keypads
* '''fish tape'''
* Tool Bags
* Computer & (packed) SC32B
* Climbing harness
* Serial Cables & spares
* Sawzall
* drill

==== Food to bring out ====
* Optional

==== Probable Luggage ====
# Bob Personal Actionpacker [Bob #1]
# Work Actionpacker #1 [Bob #2]

====Rough on-site todo====
# Copy wiring of Grid Site
# Transfer wires to new multiplexer & Logger
# Snowsurveys

Jessie Cherry May 2013 Toolik Trip

2013-05-04T21:08:45Z

209.193.54.74:

== Overview ==

The met station at Toolik needs to be transferred from its tripod to a tower. The field requirements for this assignment will be outlined here.

'''Any other information not here but could be anticipated as being useful?'''
* Where is the CGR4 going / is there a spot for it already on the radiation stand?

==To Bring from Fairbanks==
* Cabling to extend thermocouple temperature profile from old enclosure to new enclosure.
* shovels for digging out buried cabling
* extension cord for moving power from old tripod to new tower
* cable splicing tools for anything that might need extending
** soldering iron
** butane
** propane torch
** solder
** heat shrink
* extra cabling
* Toolbags
* Extra data logger (CR1000, for any instruments that aren't transferred to the new logger on this trip and or don't reach... completely just a back up item)
* small actionpacker
* sled
* Climbing harness
* CGR4 Radiometer
** Also bring Precision Resistor for measuring CGR4 Thermistor
** Also need to update program with calibration constants for this sensor.

== Current Equipment On-Site==
* New tower w/ enclosure & guy wires
* Garden web cam
* Pluvio 1 (Currently installed but broken)
* Met Station w/ soil thermocouples, radiation, lake sensors on rusted tripod
* New Multiplexer
* Pluvio 2 (needs to be installed but is in the environmental data center)... has a different base than the existing one.
* Pluvio 2 base is inside the wyoming gauge snow fence sitting on the ground

== Goals ==
* Mount recalibrated AT/RH sensors
* Move power to the new enclosure
* Transfer as much equipment as possible to new tower
* Leave what can't be moved at the old site
* Install Pluvio 2
** note, pluvio 1 wire is a bit short. but should be okay with pluvio 2
* Get evaporation pan working
* Install new radiometer
* Tighten guy wires and level tower

== Needs ==
* [[TFS Site Wiring]] / cable lengths
* List cable types needed '''''?'''''
* List muxes needed '''''?'''''

==List equipment/tools need to bring==

* Conduit
* New Program (Bob Bu has draft) - Direct Link emailed 5/4/2013
** Program Git Archive:
*** [Bob's DropBox]/logger_programs/toolik_tfs/TFScamp_CR3000.CR3
* Troubleshoot Evaporation Pan
* Figure out what needs calibration

== Updates ==

* Pluvio 1 and Pluvio 2 use different base stands. Make sure to include the Pluvio 2 mounting hardware!
* Evaporation pan may not be in the budget this year if the gauging unit (Campbell 21531) needs to be replaced.
* Conduit isn't an immediate priority since this depends on the final setup.

Jessie Cherry May 2013 Toolik Trip

2013-05-04T20:41:22Z

209.193.54.74: /* List equipment/tools need to bring */

== Overview ==

The met station at Toolik needs to be transferred from its tripod to a tower. The field requirements for this assignment will be outlined here.

'''Any other information not here but could be anticipated as being useful?'''

==To Bring from Fairbanks==
* Cabling to extend thermocouple temperature profile from old enclosure to new enclosure.
* shovels for digging out buried cabling
* extension cord for moving power from old tripod to new tower
* cable splicing tools for anything that might need extending
** soldering iron
** butane
** propane torch
** solder
** heat shrink
* extra cabling
* Toolbags
* Extra data logger (CR1000, for any instruments that aren't transferred to the new logger on this trip and or don't reach... completely just a back up item)
* small actionpacker
* sled
* Climbing harness
* CGR4 Radiometer
** Also bring Precision Resistor for measuring CGR4 Thermistor
** Also need to update program with calibration constants for this sensor.

== Current Equipment On-Site==
* New tower w/ enclosure & guy wires
* Garden web cam
* Pluvio 1 (Currently installed but broken)
* Met Station w/ soil thermocouples, radiation, lake sensors on rusted tripod
* New Multiplexer
* Pluvio 2 (needs to be installed but is in the environmental data center)... has a different base than the existing one.
* Pluvio 2 base is inside the wyoming gauge snow fence sitting on the ground

== Goals ==
* Mount recalibrated AT/RH sensors
* Move power to the new enclosure
* Transfer as much equipment as possible to new tower
* Leave what can't be moved at the old site
* Install Pluvio 2
** note, pluvio 1 wire is a bit short. but should be okay with pluvio 2
* Get evaporation pan working
* Install new radiometer
* Tighten guy wires and level tower

== Needs ==
* [[TFS Site Wiring]] / cable lengths
* List cable types needed '''''?'''''
* List muxes needed '''''?'''''

==List equipment/tools need to bring==

* Conduit
* New Program (Bob Bu has draft) - Direct Link emailed 5/4/2013
** Program Git Archive:
*** [Bob's DropBox]/logger_programs/toolik_tfs/TFScamp_CR3000.CR3
* Troubleshoot Evaporation Pan
* Figure out what needs calibration

== Updates ==

* Pluvio 1 and Pluvio 2 use different base stands. Make sure to include the Pluvio 2 mounting hardware!
* Evaporation pan may not be in the budget this year if the gauging unit (Campbell 21531) needs to be replaced.
* Conduit isn't an immediate priority since this depends on the final setup.

Jessie Cherry May 2013 Toolik Trip

2013-05-04T20:39:07Z

209.193.54.74: /* To Bring from Fairbanks */

== Overview ==

The met station at Toolik needs to be transferred from its tripod to a tower. The field requirements for this assignment will be outlined here.

'''Any other information not here but could be anticipated as being useful?'''

==To Bring from Fairbanks==
* Cabling to extend thermocouple temperature profile from old enclosure to new enclosure.
* shovels for digging out buried cabling
* extension cord for moving power from old tripod to new tower
* cable splicing tools for anything that might need extending
** soldering iron
** butane
** propane torch
** solder
** heat shrink
* extra cabling
* Toolbags
* Extra data logger (CR1000, for any instruments that aren't transferred to the new logger on this trip and or don't reach... completely just a back up item)
* small actionpacker
* sled
* Climbing harness
* CGR4 Radiometer
** Also bring Precision Resistor for measuring CGR4 Thermistor
** Also need to update program with calibration constants for this sensor.

== Current Equipment On-Site==
* New tower w/ enclosure & guy wires
* Garden web cam
* Pluvio 1 (Currently installed but broken)
* Met Station w/ soil thermocouples, radiation, lake sensors on rusted tripod
* New Multiplexer
* Pluvio 2 (needs to be installed but is in the environmental data center)... has a different base than the existing one.
* Pluvio 2 base is inside the wyoming gauge snow fence sitting on the ground

== Goals ==
* Mount recalibrated AT/RH sensors
* Move power to the new enclosure
* Transfer as much equipment as possible to new tower
* Leave what can't be moved at the old site
* Install Pluvio 2
** note, pluvio 1 wire is a bit short. but should be okay with pluvio 2
* Get evaporation pan working
* Install new radiometer
* Tighten guy wires and level tower

== Needs ==
* [[TFS Site Wiring]] / cable lengths
* List cable types needed '''''?'''''
* List muxes needed '''''?'''''

==List equipment/tools need to bring==

* Conduit
* New Program (Bob Bu has draft) - Direct Link emailed 5/4/2013
* Troubleshoot Evaporation Pan
* Figure out what needs calibration

== Updates ==

* Pluvio 1 and Pluvio 2 use different base stands. Make sure to include the Pluvio 2 mounting hardware!
* Evaporation pan may not be in the budget this year if the gauging unit (Campbell 21531) needs to be replaced.
* Conduit isn't an immediate priority since this depends on the final setup.

Jessie Cherry May 2013 Toolik Trip

2013-05-04T20:35:00Z

209.193.54.74: /* List equipment/tools need to bring */

== Overview ==

The met station at Toolik needs to be transferred from its tripod to a tower. The field requirements for this assignment will be outlined here.

'''Any other information not here but could be anticipated as being useful?'''

==To Bring from Fairbanks==
* Cabling to extend thermocouple temperature profile from old enclosure to new enclosure.
* shovels for digging out buried cabling
* extension cord for moving power from old tripod to new tower
* cable splicing tools for anything that might need extending
** soldering iron
** butane
** propane torch
** solder
** heat shrink
* extra cabling
* Toolbags
* Extra data logger (CR1000, for any instruments that aren't transferred to the new logger on this trip and or don't reach... completely just a back up item)
* small actionpacker
* sled
* Climbing harness
* Precision Resistor for measuring CGR4 Thermistor

== Current Equipment On-Site==
* New tower w/ enclosure & guy wires
* Garden web cam
* Pluvio 1 (Currently installed but broken)
* Met Station w/ soil thermocouples, radiation, lake sensors on rusted tripod
* New Multiplexer
* Pluvio 2 (needs to be installed but is in the environmental data center)... has a different base than the existing one.
* Pluvio 2 base is inside the wyoming gauge snow fence sitting on the ground

== Goals ==
* Mount recalibrated AT/RH sensors
* Move power to the new enclosure
* Transfer as much equipment as possible to new tower
* Leave what can't be moved at the old site
* Install Pluvio 2
** note, pluvio 1 wire is a bit short. but should be okay with pluvio 2
* Get evaporation pan working
* Install new radiometer
* Tighten guy wires and level tower

== Needs ==
* [[TFS Site Wiring]] / cable lengths
* List cable types needed '''''?'''''
* List muxes needed '''''?'''''

==List equipment/tools need to bring==

* Conduit
* New Program (Bob Bu has draft) - Direct Link emailed 5/4/2013
* Troubleshoot Evaporation Pan
* Figure out what needs calibration

== Updates ==

* Pluvio 1 and Pluvio 2 use different base stands. Make sure to include the Pluvio 2 mounting hardware!
* Evaporation pan may not be in the budget this year if the gauging unit (Campbell 21531) needs to be replaced.
* Conduit isn't an immediate priority since this depends on the final setup.

Jessie Cherry May 2013 Toolik Trip

2013-05-04T20:34:24Z

209.193.54.74: /* To Bring from Fairbanks */

== Overview ==

The met station at Toolik needs to be transferred from its tripod to a tower. The field requirements for this assignment will be outlined here.

'''Any other information not here but could be anticipated as being useful?'''

==To Bring from Fairbanks==
* Cabling to extend thermocouple temperature profile from old enclosure to new enclosure.
* shovels for digging out buried cabling
* extension cord for moving power from old tripod to new tower
* cable splicing tools for anything that might need extending
** soldering iron
** butane
** propane torch
** solder
** heat shrink
* extra cabling
* Toolbags
* Extra data logger (CR1000, for any instruments that aren't transferred to the new logger on this trip and or don't reach... completely just a back up item)
* small actionpacker
* sled
* Climbing harness
* Precision Resistor for measuring CGR4 Thermistor

== Current Equipment On-Site==
* New tower w/ enclosure & guy wires
* Garden web cam
* Pluvio 1 (Currently installed but broken)
* Met Station w/ soil thermocouples, radiation, lake sensors on rusted tripod
* New Multiplexer
* Pluvio 2 (needs to be installed but is in the environmental data center)... has a different base than the existing one.
* Pluvio 2 base is inside the wyoming gauge snow fence sitting on the ground

== Goals ==
* Mount recalibrated AT/RH sensors
* Move power to the new enclosure
* Transfer as much equipment as possible to new tower
* Leave what can't be moved at the old site
* Install Pluvio 2
** note, pluvio 1 wire is a bit short. but should be okay with pluvio 2
* Get evaporation pan working
* Install new radiometer
* Tighten guy wires and level tower

== Needs ==
* [[TFS Site Wiring]] / cable lengths
* List cable types needed '''''?'''''
* List muxes needed '''''?'''''

==List equipment/tools need to bring==

* Conduit
* New Program (Bob Bu has draft)
* Troubleshoot Evaporation Pan
* Figure out what needs calibration

== Updates ==

* Pluvio 1 and Pluvio 2 use different base stands. Make sure to include the Pluvio 2 mounting hardware!
* Evaporation pan may not be in the budget this year if the gauging unit (Campbell 21531) needs to be replaced.
* Conduit isn't an immediate priority since this depends on the final setup.

Jessie Cherry May 2013 Toolik Trip

2013-05-04T20:33:13Z

209.193.54.74: /* To Bring from Fairbanks */

== Overview ==

The met station at Toolik needs to be transferred from its tripod to a tower. The field requirements for this assignment will be outlined here.

'''Any other information not here but could be anticipated as being useful?'''

==To Bring from Fairbanks==
* Cabling to extend thermocouple temperature profile from old enclosure to new enclosure.
* shovels for digging out buried cabling
* extension cord
* cable splicing tools
** soldering iron
** butane
** propane torch
** solder
** heat shrink
* extra cabling
* Toolbags
* Extra data logger (CR1000, for any instruments that aren't transferred to the new logger on this trip and or don't reach... completely just a back up item)
* small actionpacker
* sled
* Climbing harness
* Precision Resistor for measuring CGR4 Thermistor

== Current Equipment On-Site==
* New tower w/ enclosure & guy wires
* Garden web cam
* Pluvio 1 (Currently installed but broken)
* Met Station w/ soil thermocouples, radiation, lake sensors on rusted tripod
* New Multiplexer
* Pluvio 2 (needs to be installed but is in the environmental data center)... has a different base than the existing one.
* Pluvio 2 base is inside the wyoming gauge snow fence sitting on the ground

== Goals ==
* Mount recalibrated AT/RH sensors
* Move power to the new enclosure
* Transfer as much equipment as possible to new tower
* Leave what can't be moved at the old site
* Install Pluvio 2
** note, pluvio 1 wire is a bit short. but should be okay with pluvio 2
* Get evaporation pan working
* Install new radiometer
* Tighten guy wires and level tower

== Needs ==
* [[TFS Site Wiring]] / cable lengths
* List cable types needed '''''?'''''
* List muxes needed '''''?'''''

==List equipment/tools need to bring==

* Conduit
* New Program (Bob Bu has draft)
* Troubleshoot Evaporation Pan
* Figure out what needs calibration

== Updates ==

* Pluvio 1 and Pluvio 2 use different base stands. Make sure to include the Pluvio 2 mounting hardware!
* Evaporation pan may not be in the budget this year if the gauging unit (Campbell 21531) needs to be replaced.
* Conduit isn't an immediate priority since this depends on the final setup.

Jessie Cherry May 2013 Toolik Trip

2013-05-04T20:29:55Z

209.193.54.74:

== Overview ==

The met station at Toolik needs to be transferred from its tripod to a tower. The field requirements for this assignment will be outlined here.

'''Any other information not here but could be anticipated as being useful?'''

==To Bring from Fairbanks==
* Cabling to extend thermocouple temperature profile from old enclosure to new enclosure.
* shovels for digging out buried cabling
* extension cord
* cable splicing tools
** soldering iron
** butane
** propane torch
** solder
** heat shrink
* extra cabling
* Toolbags
* Extra data logger (CR1000, for any instruments that aren't transferred to the new logger on this trip and or don't reach... completely just a back up item)
* small actionpacker
* sled
* Climbing harness

== Current Equipment On-Site==
* New tower w/ enclosure & guy wires
* Garden web cam
* Pluvio 1 (Currently installed but broken)
* Met Station w/ soil thermocouples, radiation, lake sensors on rusted tripod
* New Multiplexer
* Pluvio 2 (needs to be installed but is in the environmental data center)... has a different base than the existing one.
* Pluvio 2 base is inside the wyoming gauge snow fence sitting on the ground

== Goals ==
* Mount recalibrated AT/RH sensors
* Move power to the new enclosure
* Transfer as much equipment as possible to new tower
* Leave what can't be moved at the old site
* Install Pluvio 2
** note, pluvio 1 wire is a bit short. but should be okay with pluvio 2
* Get evaporation pan working
* Install new radiometer
* Tighten guy wires and level tower

== Needs ==
* [[TFS Site Wiring]] / cable lengths
* List cable types needed '''''?'''''
* List muxes needed '''''?'''''

==List equipment/tools need to bring==

* Conduit
* New Program (Bob Bu has draft)
* Troubleshoot Evaporation Pan
* Figure out what needs calibration

== Updates ==

* Pluvio 1 and Pluvio 2 use different base stands. Make sure to include the Pluvio 2 mounting hardware!
* Evaporation pan may not be in the budget this year if the gauging unit (Campbell 21531) needs to be replaced.
* Conduit isn't an immediate priority since this depends on the final setup.

TFS Site Wiring

2013-05-04T20:25:43Z

209.193.54.74:

'''5/4/2013 Note:<br> Thinking about moving AT/RH and other sensors needing 12V power from AM1632B back to CR3000 for simpler wiring in the field'''

''''''''''''''''''''''''''''''''''''''''
''''''''''''''''''''''''''''''''''''''''
'' TELEMETRY ''''
'' Maxon Data Radio @ 152.480 MHz ''''
''''''''''''''''''''''''''''''''''''''''
''''''''''''''''''''''''''''''''''''''''

''''''''''''''''''''''''''''''''''''''''''''''''''''''
''''''''''''''''''''''''''''''''''''''''''''''''''''''
''' SENSOR LIST '''''''''''''''''''''''''''''''''''
''''''''''''''''''''''''''''''''''''''''''''''''''''''
''''''''''''''''''''''''''''''''''''''''''''''''''''''
' Kipp and Zonen CGR-4 Net Radiometer
' CS420 Lake Level Pressure Transducer
' 107 Temperature Probe
' CS100 Setra Barometric Pressure Sensor
' MetOne 024A Wind Direction Sensor
' MetOne 014A Wind Speed Sensor
' Evaporation Pan Pressure Transducer
' AM25T Thermocouple multiplexer with 18 connected thermocouples
' Ott Pluvio Precipitation Gage
' Tipping Bucket Rain Gage (?)
' CMP6 Pyranometer
' Li-Cor Quantum. Model LI-190SB
' Li-Cor Underwater Quantum. LI-192SB
' UVA_YES Pyranometer
' UVB_YES Pyranometer
' HMP45C AT/RH Sensor at 5m
' RM Young 41382VF AT/RH Sensor at 3m

'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
''' LOGGER WIRING ''''''''''''''''''''''''''''''''''''''
'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
' SE1 -- Kipp and Zonen CGR-4 HI (Red Wire)
' SE2 -- Kipp and Zonen CGR-4 LO (Blue Wire)
' SE3 --
' SE4 -- Kipp and Zonen CGR-4 Thermistor (Green Wire) & Precision Resistor to VX2
' SE5 -- CS420 Lake Level (Orange Wire)
' SE6 -- CS420 Lake Level (Black Wire)
' SE7 -- CS420 Lake Level (White Wire)
' SE8 -- CS420 Lake Level (Yellow Wire Wire)
' SE9 -- 107 Temperature Signal (Red Wire)
' SE10 -- Barometric Pressure Signal (Yellow Wire) ## This is what I have from notes but it is contrary to what the CS100 manual says.
' SE11 --
' SE12 --
' SE13 -- AM25T HI
' SE14 -- AM25T LO
' SE15 -- Met One 024A WD (Red Wire)
' SE16 -- Evaporation (Red Wire)
' SE17 --
' SE18 --
' SE19 -- AM16/32B HI
' SE20 -- AM16/32B LO
' SE21 --
' SE22 --
' SE23 --
' SE24 --
' SE25 --
' SE26 --
' SE27 --
' SE28 --
'
'VX1 -- 107 Temperature Excite (Black Wire); Wind Direction Excite (Black Wire)
'VX2 -- AM25T Excite (Yellow Wire); Precision Resistor to SE4
'VX3 -- Evap Excite (White Wire)
'VX4 -- CS420 Excite (Red Wire)
'
'P1 -- Empty
'P2 -- 5m MetOne 014A Wind Speed (Black Wire)
'P3 -- Ott Pluvio Rain (Green Wire)
'P4 -- Rain 2 (NOT sure what this Is going To) (Red Wire)
'
'C1 -- AM25T RES (Red Wire)
'C2 -- AM25T CLK (Yellow Wire); AM16/32B CLK
'C3 -- Barometric Pressure CTRL
'C4 -- AM16/32B RES
'C5 -- Empty
'C6 -- HMP45C CTRL (Orange Wire)
'C7 -- Empty
'C8 -- Empty

'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
''' AM25T Wiring (HI = Blue Wire; LO = Red Wire) ''''''''
'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
' Group1 -- EvapoTC
' Group2 -- soil2_moss
' Group3 -- soil2_5cm
' Group4 -- soil2_10cm
' Group5 -- soil2_20cm
' Group6 -- soil2_50cm
' Group7 -- soil2_100cm
' Group8 -- soil2_150cm
' Group9 -- LakeTC_C
' Group10 -- NA10
' Group11 -- NA11
' Group12 -- soil1_moss
' Group13 -- soil1_20cm
' Group14 -- soil1_150cm
' Group15 -- soil1_5cm
' Group16 -- soil1_10cm
' Group17 -- soil1_50cm
' Group18 -- soil1_100cm

'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
''' AM16/32B in 2/32 Mode Wiring '''''''''''''''''''''''''
'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
' RES -- CR1000 C4
' CLK -- CR1000 C2
' COM ODD HI -- CR1000 SE19
' COM ODD LO -- CR1000 SE20
'Group1 HI CMP6 Pyranometer HI (Red Wire / Yellow Cable)
' LO CMP6 Pyranometer LO (Blue Wire / Yellow Cable)
'Group2 HI Li-Cor Quantum. Model LI-190SB HI (Red Wire)
' LO Li-Cor Quantum. Model LI-190SB LO (Black Wire)
'Group3 HI Li-Cor Underwater Quantum. LI-192SB HI (Red Wire)
' LO Li-Cor Underwater Quantum. LI-192SB LO (Black Wire)
'Group4 HI Differential Voltage measurements UVA_YES Watts/m2 HI (White Wire)
' LO Differential Voltage measurements UVA_YES Watts/m2 LO (Black Wire)
'Group5 HI Differential Voltage measurements UVB_YES Watts/m2 HI (White Wire)
' LO Differential Voltage measurements UVB_YES Watts/m2 LO (Black Wire)
'Group6 HI HMP45C at 5m AT HI (Yellow Wire)
' LO HMP45C at 5m AT LO, Jumper To G7LO (Purple Wire)
'Group7 HI HMP45C at 5m RH HI (Blue Wire)
' LO HMP45C at 5m RH LO, Jumper To G6LO (Purple Wire)
'Group8 HI RM Young 41382VF Air Temperature at 3m (Red Wire)
' LO RM Young 41382VF Air Temperature at 3m, Jumper to Group 9 LO (Black Wire)
'Group9 HI RM Young 41382VF Relative Humidity Sensor at 3m (Green Wire)
' LO RM Young 41382VF Relative Humidity Sensor at 3m (Jumper to Group 8 LO)

'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
'' Sensor Wiring ''''''''''''''''''''''''''''''''''''''
'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
' Kipp and Zonen CGR-4
' Red Wire -- CR1000 SE1
' Blue Wire -- CR1000 SE2
' Green Wire -- CR1000 SE4 & Precision Resistor to VX2

' CS420 Lake Level Pressure Transducer
' Orange Wire -- CR1000 SE5
' Black Wire -- CR1000 SE6
' White Wire -- CR1000 SE7
' Yellow Wire -- CR1000 SE8
' Red Wire -- VX4
' ____ Wires -- CR1000 Signal Ground

' 107 Temperature Probe
' Red Wire -- CR1000 SE9
' Black Wire -- CR1000 Vx1
' Purple Wire -- CR1000 Signal Ground
' Clear Wire -- CR1000 Signal Ground

' CS100 - Setra Model 278 Barometric Pressure
' Need to get more info on site about the sensor wiring for this sensor. 5/2013
' Yellow Wire -- CR1000 SE10
' BP CTRL -- CR1000 C3
' Other wiring... TBD

' Met One 024A Wind Direction Sensor
' Red Wire -- CR1000 SE15
' Black Wire -- CR1000 VX1
' White Wire -- CR1000 Signal Ground

' MetOne 014A Wind Speed Sensor
' Black Wire -- CR1000 P2
' White Wire -- CR1000 Signal Ground
' Clear Wire -- CR1000 Signal Ground

' Evaporation Pan
' Red Wire -- CR1000 SE16
' White Wire -- CR1000 VX3
' TBD -- CR1000 Signal Ground

' CMP6 Pyranometer
' Red Wire -- AM16/32B Group 1 HI
' Blue Wire -- AM16/32B Group 1 LO

' Li-Cor Quantum Model LI-190SB
' Red Wire -- AM16/32B Group 2 HI
' Black Wire -- Am16/32B Group 2 LO

' Li-Cor Underwater Quantum. LI-192SB
' Red Wire -- AM16/32B Group 3 HI
' Black Wire -- AM16/32B Group 3 LO

' Yankee Environmental Systems UV A Pyranometer
' White Wire -- AM16/32B Group 4 HI
' Black Wire -- AM16/32B Group 4 LO

' Yankee Environmental Systems UV B Pyranometer
' White Wire -- AM16/32B Group 5 HI
' Black Wire -- AM16/32B Group 5 LO

' Vaisala HMP45C Air Temperature / Relative Humidity @ 5m
' Yellow Wire -- AM16/32B Group 6 HI
' Blue Wire -- AM16/32B Group 7 Hi
' Purple Wire -- AM16/32B Group 6 & 7 LO
' Orange Wire -- CR1000 C6
' Red Wire -- CR100 12V
' Black Wire -- CR1000 G
' Clear Wire -- CR1000 G

' RM Young 41382VF AT/RH @ 3m
' Red Wire -- AM16/32B Group 8 HI
' Green Wire -- AM16/32B Group 9 HI
' Black Wire -- AM16/32B Group 8 & 9 LO

Jessie Cherry May 2013 Toolik Trip

2013-05-04T18:44:36Z

209.193.54.74:

== Overview ==

The met station at Toolik needs to be transferred from its tripod to a tower. The field requirements for this assignment will be outlined here.

==To Bring from Fairbanks==
* Cabling to extend thermocouple temperature profile from old enclosure to new enclosure.
* shovels for digging out buried cabling
* extension cord
* cable splicing tools
** soldering iron
** butane
** propane torch
** solder
** heat shrink
* extra cabling
* Toolbags
* Extra data logger (CR1000, for any instruments that aren't transferred to the new logger on this trip and or don't reach... completely just a back up item)
* small actionpacker
* sled
* Climbing harness

== Current Equipment On-Site==
* New tower w/ enclosure & guy wires
* Garden web cam
* Pluvio 1 (Currently installed but broken)
* Met Station w/ soil thermocouples, radiation, lake sensors on rusted tripod
* New Multiplexer
* Pluvio 2 (needs to be installed but is in the environmental data center)... has a different base than the existing one.
* Pluvio 2 base is inside the wyoming gauge snow fence sitting on the ground

== Goals ==
* Mount recalibrated AT/RH sensors
* Move power to the new enclosure
* Transfer as much equipment as possible to new tower
* Leave what can't be moved at the old site
* Install Pluvio 2
** note, pluvio 1 wire is a bit short. but should be okay with pluvio 2
* Get evaporation pan working
* Install new radiometer
* Tighten guy wires and level tower

== Needs ==
* [[TFS Site Wiring]] / cable lengths
* List cable types needed '''''?'''''
* List muxes needed '''''?'''''

==List equipment/tools need to bring==

* Conduit
* New Program (Bob Bu has draft)
* Troubleshoot Evaporation Pan
* Figure out what needs calibration

== Updates ==

* Pluvio 1 and Pluvio 2 use different base stands. Make sure to include the Pluvio 2 mounting hardware!
* Evaporation pan may not be in the budget this year if the gauging unit (Campbell 21531) needs to be replaced.
* Conduit isn't an immediate priority since this depends on the final setup.

NGEE Barrow 2013 Site Install Trip

2013-04-29T00:25:00Z

209.193.54.74:

==May 2013 Trip==
Purpose:
* Fix Grid Site station
* Snow Surveys
* Any other prep that's possible

===Shipping===

===To Do as of 4/21/2013===
* Modify Programs
* Wiring Diagrams
* PRs for freight
* Sketch up site
* cut crossarms to length
* Change SDI-12 IDs for SR50As
* Review Site C data... Look closely at SR50A data for precise failure dates.
* SM Grid rewiring?

=== Remaining things to grab===
* ?

===To Purchase===
* ?

===Pre-trip to do===

===Things to buy===
* Bit o' Food?
* ?

===Stuff to bring===
* Adirondack Tube
* Scale
* Thaw Probe
* Ziplocs
* GPS
* If NuRail fittings ever arrive then we can change out the tripod poles (or start) this trip.

==== things not on a PR yet====

==== Technical Gear ====
* '''Shotgun'''
* Keypads
* '''fish tape'''
* Tool Bags
* Computer & (packed) SC32B
* Climbing harness
* Serial Cables & spares
* Sawzall
* drill

==== Food to bring out ====
* Optional

==== Probable Luggage ====
# Shotgun [Bob #1]
# Bob Personal backpack [Bob #2]
# Work Actionpacker #1 [Bob #3]
#

====Rough on-site todo====
# Copy wiring of Grid Site
# Transfer wires to new multiplexer & Logger
# Snowsurveys

NGEE

2013-04-29T00:18:59Z

209.193.54.74: /* Trips */

===Notes===
* [[NGEE Barrow Intensive Sites Initial Wiring]]
* Programs:
** https://github.com/frankohanlon/ngee/

===Metadata type stuff===
* Still to be collated: [[NGEE-Barrow Calibration and Serial Numbers]]
* Thermistor Probe Calibrations ([https://docs.google.com/open?id=0B0bJdr7FBoY-MG9FTjFCb2w2c28])
* Thermistor Strings and Triple Calibrations ([https://docs.google.com/open?id=0B0bJdr7FBoY-WkVfMDdLX3Zjc2c])
* Timezone - UTC
* PakBus IDs - A = 400; B = 401; C = 402; D = 403
====Lists====
* [[Guruplug Setup]]
* [[Webcam Tips]]

===Trips===
* [[NGEE April 11 2012 Trip]]
* [[NGEE September 3 2012 Trip]]
* [[NGEE September 24 2012 Trip]]
* [[NGEE Barrow Wiring Layout]]
* [[NGEE Barrow Intensive Sites Initial Wiring]]
* [[NGEE Barrow 2013 Boring Trip]]
* [[NGEE Barrow 2013 Site Install Trip|[NGEE Barrow 2013 Site Install Trip 5/7]]
* [[NGEE Barrow 2013 Site Install Trip 2|NGEE Barrow 2013 Site Install Trip June]]
* [[NGEE Barrow Remainder Items]]
* [[CPCRW 2012-10-12]]

NGEE Barrow 2013 Site Install Trip 2

2013-04-29T00:18:09Z

209.193.54.74:

==June 2013 Trip==

===Shipping===
* New Instrumentation once it arrives on 5/26ish:
** Precip Buckets 3x
** Wind Screen 3x
** HMP155s 6x
** MetOne 5x
** Barometric Pressure
** Radiation Shields
** Cross Arms
*** 1.5" Sched 40 Aluminum = Net Radiometer 3x
*** 1" Sched 40 Aluminum = Upper WS & AT/RH 3x
** Tripod Mast
*** 1.5" Sched 40 Galvanized Pipe
** Net Radiometer
** NuRail Fittings for crossarms

===To Add to each site===
* 2 HMP155s w/ Radiation Shields
* 2 Met One WS
* 1 Tipping Bucket w/ Windscreen
* 1 CNR4 Net Radiometer with Heater/Fan Control
* 1 AM16/32

===Additionally, to add to Site A===
* CS106 Barometric Pressure

===Rewiring at each site===
* Move AM16/32B #1 & #2 RES to CR1000 C1
* Move SR50A Green Wire to CR1000 C5
** Reprogram the IDs for the SR50As
*** #1 = ID7
*** #2 = ID8
*** #3 = ID9

===To Do as of 4/21/2013===
* Modify Programs
* Wiring Diagrams
* PRs for freight
* Sketch up site
* Wire up boxes as much as possible (is anything possible? Maybe just mount the peripherals)
* Review pictures to see if a second box is still needed for just the multiplexer.
* holes in box for instrumentation maybe?
* cut crossarms to length
* Change SDI-12 IDs for SR50As
* Review Site C data... Look closely at SR50A data for precise failure dates.
* SM Grid rewiring?

=== Remaining things to grab===
* ?

===To Purchase===
* ?

===Pre-trip to do===
* Organized per site items ('''X''' means it's packed / shipped)
** Precip Stand (3 sets)
*** 4 NuRail 3/4 offset cross pieces
*** 1 Novalynx Wind Screen
*** 1 TE525m & Cable

** Tripod Related
***
***
****
****
****
****
****
****
****

===Things to buy===
* Bit o' Food?
* ?

===Stuff to bring===

==== things not on a PR yet====

==== Technical Gear ====
* '''Shotgun'''
* Keypads
* '''fish tape'''
* Tool Bags
* Computer & (packed) SC32B
* Climbing harness
* Serial Cables & spares
* Sawzall
* drill

==== Food to bring out ====
* Optional

==== Probable Luggage ====
# Shotgun [Bob #1]
# Bob Personal backpack [Bob #2]
# Work Actionpacker #1 [Bob #3]
#

====Rough on-site todo====
# Remove box & solar panel
# Measure from top of tripod base to cross arm... note in fieldbook
# Remove crossarm off tripod
# unscrew center pole
# put 1.5" offset nurail fitting on new center pole
# attach new center pole
# put cross arm, instrument box, and solar panel back on the tower.
# Install new instrument box on lower leg.
# Mount all new sensors
## Net Radiometer @ 1-1.5m
## WS on radiometer crossarm
## HMP155 on radiometer crossarm
## Second HMP155 & WS high up on tower, maybe as high as they'll reach.
## Armor all the cabling
## Armor and install the precip bucket.
## Install the precip wind screen
# send new program to data logger

NGEE

2013-04-28T23:59:19Z

209.193.54.74: /* Trips */

===Notes===
* [[NGEE Barrow Intensive Sites Initial Wiring]]
* Programs:
** https://github.com/frankohanlon/ngee/

===Metadata type stuff===
* Still to be collated: [[NGEE-Barrow Calibration and Serial Numbers]]
* Thermistor Probe Calibrations ([https://docs.google.com/open?id=0B0bJdr7FBoY-MG9FTjFCb2w2c28])
* Thermistor Strings and Triple Calibrations ([https://docs.google.com/open?id=0B0bJdr7FBoY-WkVfMDdLX3Zjc2c])
* Timezone - UTC
* PakBus IDs - A = 400; B = 401; C = 402; D = 403
====Lists====
* [[Guruplug Setup]]
* [[Webcam Tips]]

===Trips===
* [[NGEE April 11 2012 Trip]]
* [[NGEE September 3 2012 Trip]]
* [[NGEE September 24 2012 Trip]]
* [[NGEE Barrow Wiring Layout]]
* [[NGEE Barrow Intensive Sites Initial Wiring]]
* [[NGEE Barrow 2013 Boring Trip]]
* [[NGEE Barrow 2013 Site Install Trip|[NGEE Barrow 2013 Site Install Trip 1]]
* [[NGEE Barrow 2013 Site Install Trip 2]]
* [[NGEE Barrow Remainder Items]]
* [[CPCRW 2012-10-12]]

NGEE Barrow 2013 Site Install Trip

2013-04-22T07:03:48Z

209.193.54.74: /* Rewiring at each site */

===Shipping===
* New Instrumentation once it arrives:
** Precip Buckets 3x
** Wind Screen 3x
** HMP155s 6x
** MetOne 5x
** Barometric Pressure
** Leg Mount Instrument Boxes 3x (Is this still required?)
*** Install AM16/32B if time
*** Install SDM Switch if time
** Radiation Shields
** Cross Arms
*** 1.5" Sched 40 Aluminum = Net Radiometer 3x
*** 1" Sched 40 Aluminum = Upper WS & AT/RH 3x
** Tripod Mast
*** 1.5" Sched 40 Galvanized Pipe

===To Add to each site===
* 2 HMP155s w/ Radiation Shields
* 2 Met One WS
* 1 Tipping Bucket w/ Windscreen
* 1 CNR4 Net Radiometer with Heater/Fan Control
* 1 AM16/32

===Additionally, to add to Site A===
* CS106 Barometric Pressure

===Rewiring at each site===
* Move AM16/32B #1 & #2 RES to CR1000 C1
* Move SR50A Green Wire to CR1000 C5
** Reprogram the IDs for the SR50As
*** #1 = ID7
*** #2 = ID8
*** #3 = ID9

===To Do as of 4/21/2013===
* Modify Programs
* Wiring Diagrams
* PRs for freight
* Sketch up site
* Wire up boxes as much as possible (is anything possible? Maybe just mount the peripherals)
* Review pictures to see if a second box is still needed for just the multiplexer.
* holes in box for instrumentation maybe?
* cut crossarms to length
* Change SDI-12 IDs for SR50As
* Review Site C data... Look closely at SR50A data for precise failure dates.
* SM Grid rewiring?

=== Remaining things to grab===
* ?

===To Purchase===
* ?

===Pre-trip to do===
* Organized per site items ('''X''' means it's packed / shipped)
** Precip Stand (3 sets)
*** 4 NuRail 3/4 offset cross pieces
*** 1 Novalynx Wind Screen
*** 1 TE525m & Cable

** Tripod Related
***
***
****
****
****
****
****
****
****

===Things to buy===
* Bit o' Food?
* ?

===Stuff to bring===

==== things not on a PR yet====

==== Technical Gear ====
* '''Shotgun'''
* Keypads
* '''fish tape'''
* Tool Bags
* Computer & (packed) SC32B
* Climbing harness
* Serial Cables & spares
* Sawzall
* drill

==== Food to bring out ====
* Optional

==== Probable Luggage ====
# Shotgun [Bob #1]
# Bob Personal backpack [Bob #2]
# Work Actionpacker #1 [Bob #3]
#

====Rough on-site todo====
# Remove box & solar panel
# Measure from top of tripod base to cross arm... note in fieldbook
# Remove crossarm off tripod
# unscrew center pole
# put 1.5" offset nurail fitting on new center pole
# attach new center pole
# put cross arm, instrument box, and solar panel back on the tower.
# Install new instrument box on lower leg.
# Mount all new sensors
## Net Radiometer @ 1-1.5m
## WS on radiometer crossarm
## HMP155 on radiometer crossarm
## Second HMP155 & WS high up on tower, maybe as high as they'll reach.
## Armor all the cabling
## Armor and install the precip bucket.
## Install the precip wind screen
# send new program to data logger

NGEE Barrow 2013 Site Install Trip

2013-04-22T07:01:59Z

209.193.54.74:

===Shipping===
* New Instrumentation once it arrives:
** Precip Buckets 3x
** Wind Screen 3x
** HMP155s 6x
** MetOne 5x
** Barometric Pressure
** Leg Mount Instrument Boxes 3x (Is this still required?)
*** Install AM16/32B if time
*** Install SDM Switch if time
** Radiation Shields
** Cross Arms
*** 1.5" Sched 40 Aluminum = Net Radiometer 3x
*** 1" Sched 40 Aluminum = Upper WS & AT/RH 3x
** Tripod Mast
*** 1.5" Sched 40 Galvanized Pipe

===To Add to each site===
* 2 HMP155s w/ Radiation Shields
* 2 Met One WS
* 1 Tipping Bucket w/ Windscreen
* 1 CNR4 Net Radiometer with Heater/Fan Control
* 1 AM16/32

===Additionally, to add to Site A===
* CS106 Barometric Pressure

===Rewiring at each site===
* Move AM16/32B #1 & #2 RES to CR1000 C1
* Move SR50A Green Wire to CR1000 C5

===To Do as of 4/21/2013===
* Modify Programs
* Wiring Diagrams
* PRs for freight
* Sketch up site
* Wire up boxes as much as possible (is anything possible? Maybe just mount the peripherals)
* Review pictures to see if a second box is still needed for just the multiplexer.
* holes in box for instrumentation maybe?
* cut crossarms to length
* Change SDI-12 IDs for SR50As
* Review Site C data... Look closely at SR50A data for precise failure dates.
* SM Grid rewiring?

=== Remaining things to grab===
* ?

===To Purchase===
* ?

===Pre-trip to do===
* Organized per site items ('''X''' means it's packed / shipped)
** Precip Stand (3 sets)
*** 4 NuRail 3/4 offset cross pieces
*** 1 Novalynx Wind Screen
*** 1 TE525m & Cable

** Tripod Related
***
***
****
****
****
****
****
****
****

===Things to buy===
* Bit o' Food?
* ?

===Stuff to bring===

==== things not on a PR yet====

==== Technical Gear ====
* '''Shotgun'''
* Keypads
* '''fish tape'''
* Tool Bags
* Computer & (packed) SC32B
* Climbing harness
* Serial Cables & spares
* Sawzall
* drill

==== Food to bring out ====
* Optional

==== Probable Luggage ====
# Shotgun [Bob #1]
# Bob Personal backpack [Bob #2]
# Work Actionpacker #1 [Bob #3]
#

====Rough on-site todo====
# Remove box & solar panel
# Measure from top of tripod base to cross arm... note in fieldbook
# Remove crossarm off tripod
# unscrew center pole
# put 1.5" offset nurail fitting on new center pole
# attach new center pole
# put cross arm, instrument box, and solar panel back on the tower.
# Install new instrument box on lower leg.
# Mount all new sensors
## Net Radiometer @ 1-1.5m
## WS on radiometer crossarm
## HMP155 on radiometer crossarm
## Second HMP155 & WS high up on tower, maybe as high as they'll reach.
## Armor all the cabling
## Armor and install the precip bucket.
## Install the precip wind screen
# send new program to data logger

NGEE Barrow Intensive Sites Initial Wiring

2013-04-22T06:52:06Z

209.193.54.74:

===General Wiring 2013===
(With some minor differences between sites:)
* 3 SR50As at site C
* 1 CS106 at site A
* In May reprogram the SR50As with new addresses.
** SR50A #1 = SDI-12 ID 7
** SR50A #2 = SDI-12 ID 8
** SR50A #3 = SDI-12 ID 9

' SE1 -- CNR4 SW In HI
' SE2 -- CNR4 SW In LO
' SE3 -- CNR4 SW OUT HI
' SE4 -- CNR4 SW OUT LO
' SE5 -- CNR4 LW IN HI
' SE6 -- CNR4 LW IN LO
' SE7 -- CNR4 Dome Temperature Signal
' SE8 -- 107 Probe Signal (Red Wire)
' SE9 -- CNR4 LW OUT HI
' SE10 -- CNR4 LW OUT LO
' SE11 -- AM16/32B #3 COM ODD HI
' SE12 -- AM16/32B #3 COM ODD LO
' SE13 -- AM16/32B #1 COM ODD HI, Precision Resistor to VX2
' SE14 -- AM16/32B #1 COM ODD LO, Precision Resistor to VX2
' SE15 -- AM16/32B #2 COM ODD HI, Precision Resistor to VX3
' SE16 -- AM16/32B #2 COM ODD LO, Precision Resistor to VX3

' VX1 -- 107 Probe Excitation (Black Wire); **CNR4 LW Dome Temperature Excitation**, **RM Young WD Excite**
' VX2 -- Precision resistors to Mux 2 COM ODD HI, SE1, COM ODD LO, SE2
' VX3 -- Precision resistors to Mux 3 COM ODD HI, SE1, COM ODD LO, SE2,

' P1 -- MetOne 1m WS+
' P2 -- MetOne 3.5m WS+

' C1 -- AM16/32B #1 & AM16/32B #2 -- RES
' C2 -- AM16/32B #3 -- RES; HMP155 CTRL; (optionally: CS106 CTRL)
' C3 -- CNR4 Heater/Fan Control
' C4 -- AM16/32B #1, 2, & 3 -- CLK
' C5 -- SDI 12 Devices -- (6 Vitel Probes ) (Blue Wire); ; (2 SR50A ) (Green Wire)
' C6 -- Vitel Probe CONTROL (Run to SW12V Control for Vitel Probes)
' C7 -- TE525M Signal
' C8 -- Thermal Conductivity Control
' SW12V -- Radio Power

' Wiring that will need to be moved in May 2013
' C1 -- Move AM16/32B #1 & #2 RES to here

' Signal Ground -- HFP01 Shields (Clear Wire), 107 Probe SG (Purple Wire), SR50A

I think I'll need to make available some additional 12V & G power points. Also... if I drop the SDM interface can I get everything into the original logger box?? Just adding more instruments plus a multiplexer all of a sudden.

NGEE Barrow Intensive Sites Initial Wiring

2013-04-22T06:40:02Z

209.193.54.74:

===General Wiring 2013===
(With some minor differences between sites:)
* 3 SR50As at site C
* 1 CS106 at site A

' SE1 -- CNR4 SW In HI
' SE2 -- CNR4 SW In LO
' SE3 -- CNR4 SW OUT HI
' SE4 -- CNR4 SW OUT LO
' SE5 -- CNR4 LW IN HI
' SE6 -- CNR4 LW IN LO
' SE7 -- CNR4 Dome Temperature Signal
' SE8 -- 107 Probe Signal (Red Wire)
' SE9 -- CNR4 LW OUT HI
' SE10 -- CNR4 LW OUT LO
' SE11 -- AM16/32B #3 COM ODD HI
' SE12 -- AM16/32B #3 COM ODD LO
' SE13 -- AM16/32B #1 COM ODD HI, Precision Resistor to VX2
' SE14 -- AM16/32B #1 COM ODD LO, Precision Resistor to VX2
' SE15 -- AM16/32B #2 COM ODD HI, Precision Resistor to VX3
' SE16 -- AM16/32B #2 COM ODD LO, Precision Resistor to VX3

' VX1 -- 107 Probe Excitation (Black Wire); **CNR4 LW Dome Temperature Excitation**, **RM Young WD Excite**
' VX2 -- Precision resistors to Mux 2 COM ODD HI, SE1, COM ODD LO, SE2
' VX3 -- Precision resistors to Mux 3 COM ODD HI, SE1, COM ODD LO, SE2,

' P1 -- MetOne 1m WS+
' P2 -- MetOne 3.5m WS+

' C1 -- AM16/32B #1 & AM16/32B #2 -- RES
' C2 -- AM16/32B #3 -- RES; HMP155 CTRL; (optionally: CS106 CTRL)
' C3 -- CNR4 Heater/Fan Control
' C4 -- AM16/32B #1, 2, & 3 -- CLK
' C5 -- SDI 12 Devices -- (6 Vitel Probes ) (Blue Wire); ; (2 SR50A ) (Green Wire)
' C6 -- Vitel Probe CONTROL (Run to SW12V Control for Vitel Probes)
' C7 -- TE525M Signal
' C8 -- Thermal Conductivity Control
' SW12V -- Radio Power

' Wiring that will need to be moved in May 2013
' C1 -- Move AM16/32B #1 & #2 RES to here

' Signal Ground -- HFP01 Shields (Clear Wire), 107 Probe SG (Purple Wire), SR50A

I think I'll need to make available some additional 12V & G power points. Also... if I drop the SDM interface can I get everything into the original logger box?? Just adding more instruments plus a multiplexer all of a sudden.

NGEE Barrow Intensive Sites Initial Wiring

2013-04-22T03:32:40Z

209.193.54.74:

General Wiring 2013
(Some minor differences like 3 SR50As at site C)

' SE1 -- CNR4 SW In HI
' SE2 -- CNR4 SW In LO
' SE3 -- CNR4 SW OUT HI
' SE4 -- CNR4 SW OUT LO
' SE5 -- CNR4 LW IN HI
' SE6 -- CNR4 LW IN LO
' SE7 -- CNR4 Dome Temperature Signal
' SE8 -- 107 Probe Signal (Red Wire)
' SE9 -- CNR4 LW OUT HI
' SE10 -- CNR4 LW OUT LO
' SE11 -- AM16/32B #3 COM ODD HI
' SE12 -- AM16/32B #3 COM ODD LO
' SE13 -- AM16/32B #1 COM ODD HI, Precision Resistor to VX2
' SE14 -- AM16/32B #1 COM ODD LO, Precision Resistor to VX2
' SE15 -- AM16/32B #2 COM ODD HI, Precision Resistor to VX3
' SE16 -- AM16/32B #2 COM ODD LO, Precision Resistor to VX3

' VX1 -- 107 Probe Excitation (Black Wire); **CNR4 LW Dome Temperature Excitation**, **RM Young WD Excite**
' VX2 -- Precision resistors to Mux 2 COM ODD HI, SE1, COM ODD LO, SE2
' VX3 -- Precision resistors to Mux 3 COM ODD HI, SE1, COM ODD LO, SE2,

' P1 -- MetOne 1m WS+
' P2 -- MetOne 3.5m WS+

' C1 -- SDM IO C1
' C2 -- SDM IO C2
' C3 -- SDM IO C3
' C4 -- AM16/32B #1, 2, & 3 -- CLK
' C5 -- SDI 12 Devices Part 1 (6 Vitel Probes ) (Blue Wire)
' C6 -- Vitel Probe CONTROL (Run to SW12V Control for Vitel Probes)
' C7 -- SDI 12 Devices Part 2 (2 SR50A ) (Green Wire)
' C8 -- TE525M Signal
' SW12V -- Radio Power

' Wiring that will need to be moved / extended to the SDM Interface:
' C2 -- AM16/32B #1 -- RES
' C3 -- AM16/32B #2 -- RES
' C8 -- Thermal Conductivity Control

' Signal Ground -- HFP01 Shields (Clear Wire), 107 Probe SG (Purple Wire), SR50A

' SDM Interface Wiring:
' 1 -- AM16/32B #1 RES
' 2 -- AM16/32B #2 RES
' 3 -- AM16/32B #3 RES
' 4 -- Thermal Conductivity Control
' 5 -- HMP155 Control
' 6 -- CNR4 Heater/Fan Control

NGEE Barrow 2013 Boring Trip

2013-04-15T05:16:36Z

209.193.54.74:

...coring is more accurate than boring... not sure how that slipped through...

Stuff to do prior to:
* XX Understand how to do the stakeout method of RTK survey
* Can our R8s rx at 418mhz? ... yes. Need to get that setup / just check up there for it.
* setup loggernet.iarc.uaf.edu and transfer the barrow dreamplug data there?
* check installed programs on barrow dreamplug
sudo dpkg -get-selections | grep -v deinstall > installed_packages-2012_07.txt
* XX load coring holes onto GPS
* scan fieldbook
* Print this page and workplan from Dave

Barrow Tasks:
* Download Grid Soil Moisture Data
* Change power supply for dreamplug
* check out C site SR50A cables to see if they can be repaired etc.
* Check on Grid Battery

Stuff to bring:
* XX small toolbag
* XX Shotgun
* XX GPS setup
* XX Toughbook & charger
* XX Trimble Chargers (2)
* XX SC32B
* XX Serial Cables

* XX new butane soldering iron in waterproof case
* XX solder?
* XX PPE:
** XX Helmets
** XX Hearing Protection
** XX Safety Glasses

NGEE Barrow 2013 Boring Trip

2013-04-14T21:25:26Z

209.193.54.74:

...coring is more accurate than boring... not sure how that slipped through...

Stuff to do prior to:
* XX Understand how to do the stakeout method of RTK survey
* Can our R8s rx at 418mhz? ... yes. Need to get that setup.
* setup loggernet.iarc.uaf.edu and transfer the barrow dreamplug data there?
* check installed programs on barrow dreamplug
* XX load coring holes onto GPS
* scan fieldbook
* Print this page and workplan from Dave

Stuff that is at work:
* chargers for Trimble stuff
** R8 batteries
** TSC3 charger
* Hardhats
* eye protection
* ear protection
* SC32B
* Camera tripod
* blackberry
* Trimble Serial Cable to Lemo
* ???
* Larry's GPS

Stuff to bring:
* small toolbag
* Shotgun
* GPS setup
* Toughbook
* SC32B
* Serial Cables
* Toolbags
* replacement power supply for barrow dreamplug
* new butane soldering iron in waterproof case
* solder?
* PPE:
*** Helmets
*** Hearing Protection
*** Safety Glasses

Barrow Tasks:
* Download Grid Soil Moisture Data
* Change power supply for dreamplug
* check out C site SR50A cables to see if they can be repaired etc.
* Check on Grid Battery

NGEE Barrow 2013 Boring Trip

2013-04-14T21:24:45Z

209.193.54.74:

...coring is more accurate than boring... not sure how that slipped through...

Stuff to do prior to:
* XX Understand how to do the stakeout method of RTK survey
* Can our R8s rx at 418mhz? ... yes. Need to get that setup.
* setup loggernet.iarc.uaf.edu and transfer the barrow dreamplug data there?
* check installed programs on barrow dreamplug
* XX load coring holes onto GPS
* scan fieldbook

Stuff that is at work:
* chargers for Trimble stuff
** R8 batteries
** TSC3 charger
* Hardhats
* eye protection
* ear protection
* SC32B
* Camera tripod
* blackberry
* Trimble Serial Cable to Lemo
* ???
* Larry's GPS

Stuff to bring:
* small toolbag
* Shotgun
* GPS setup
* Toughbook
* SC32B
* Serial Cables
* Toolbags
* replacement power supply for barrow dreamplug
* new butane soldering iron in waterproof case
* solder?
* PPE:
*** Helmets
*** Hearing Protection
*** Safety Glasses

Barrow Tasks:
* Download Grid Soil Moisture Data
* Change power supply for dreamplug
* check out C site SR50A cables to see if they can be repaired etc.
* Check on Grid Battery

NGEE Barrow 2013 Boring Trip

2013-04-14T21:04:58Z

209.193.54.74:

...coring is more accurate than boring... not sure how that slipped through...

Stuff to do prior to:
* XX Understand how to do the stakeout method of RTK survey
* Can our R8s rx at 418mhz? ... yes. Need to get that setup.
* setup loggernet.iarc.uaf.edu and transfer the barrow dreamplug data there?
* check installed programs on barrow dreamplug
* XX load coring holes onto GPS
* scan fieldbook

Stuff that is at work:
* chargers for Trimble stuff
** R8 batteries
** TSC3 charger
* Hardhats
* eye protection
* ear protection
* SC32B
* Camera tripod
* blackberry
* Trimble Serial Cable to Lemo
* ???

Stuff to bring:
* small toolbag
* Shotgun
* GPS setup
* Toughbook
* SC32B
* Serial Cables
* Toolbags
* replacement power supply for barrow dreamplug
* new butane soldering iron in waterproof case
* solder?
* PPE:
*** Helmets
*** Hearing Protection
*** Safety Glasses

Barrow Tasks:
* Download Grid Soil Moisture Data
* Change power supply for dreamplug
* check out C site SR50A cables to see if they can be repaired etc.
* Check on Grid Battery