IARC 207 Wiki - User contributions [en]

Kougraok M64

2016-08-20T02:18:44Z

66.58.163.81:

Tape Color is '''Green'''

===In NGEE Container:===
* Tripod base with green tape.
** Requires 1.25" schedule 40 pipe mast

===In UAF Storage===
* 1" x 3' aluminum pipe, three pieces
* 2 pipe wrenches
* large cable ties
* small cable ties
* fish tape
* 4 dog anchors
* saw
* grease
* anti oxidizing grease for electrical connections
* a bunch of hose clamps (including for precip bucket
* Bosch drill
* GIPL drill bit

===Sensors in UAF storage===
* Tipping bucket
* GIPL VATP

===To Buy in Nome===
* At Grizzly Hardware pick up a 1.25" schedule 40 pipe threaded on one side

===To buy in Fairbanks
* 1" topper for tripod past
* 1" to 1.25" coupler to replace one used at teller top site

===Cross arm situation===
* Use short 1" Aluminum pipe for precip stand at site. Have three of these in the UAF Nome storage as well as the brackets required.
* the hose clamps for the site are in Nome along with some other items.

===To ship from Fairbanks===
* 2 pcs 12V batteries

===Sensors===
* Met:
** HMP155AC (@1.5 meters)
*** radiation shield
** RM Young @ 3meters
** Barometric Pressure
** CNR4 for Net Radiation
** 3 NDVI sensors
** 3 other radiation sensors
** skin temperature
* Soil '' only applicable if we build at M64 rather than Pilgrim Hot Springs''
** 5 soil moisture
** 4 thermal conductivity / specific heat
** GIPL VATP

** bringing out 2 batteries for this site

===Actionpacker in uaf storage===
* Cable Ties
* 2 pipe wrenches
* hose clmaps
* three camping dinners (seafood deals)
* a bit more snacks
* fish tape
* soil samplers for teller bottom
* duct seal
* grease & anticorrosion goo
* (2) switched 12 volt control
* saw for dirt
* dog anchor
* box screw driver & serial cable (2)
* drill charger
* test radio for kougarok conenctions
** need a cigarette adapter
* hobo kit
* SR50A for K2 & K3
* 1" x 1" ubolt cross arm bracket
* 1" x 1.5" ubolt cross arm bracket
* 1" x 1" nurail cross
* 1" x 3/4" nurail cross
* LANL cameras
* bubble wrap
===General actionpacker placed into storage but may be useful for K64===
* Misc ubolts
* misc unistrut clamps (mostly wrong sizes I suspect)
* four pieces of unistrut 12-18 inches. two half size two full size
* three things of electrical tape, duct tape, rubber splicing tape
* couple NRS straps 9 & 12 feet
* 1 8GB CF card
* misc wire
* misc other
* baking soda

===Old Extras===
* Using NGEE tripod in GIPL Upark storage
* Need cross arm for Net Radiation
* Still need to put precip stand together for tipping bucket
* still ned to sort out battery box for here.

Kougraok M64

2016-08-19T23:52:38Z

66.58.163.81:

Teller Upper Station

2016-08-19T23:44:50Z

66.58.163.81: Replaced content with "'''Tape Color is Yellow''' ===Remaining To Do for fall=== * Bring out a charge controller for solar panel * soil samples from soil pit * soil pit sensors are in a large ac..."

'''Tape Color is Yellow'''
===Remaining To Do for fall===
* Bring out a charge controller for solar panel
* soil samples from soil pit
* soil pit sensors are in a large actionpacker next to tower.

Teller Lower Station

2016-08-19T23:43:38Z

66.58.163.81:

Tape Color is '''BLUE'''

===In Nome Storage:===
* jumpers for last battery
* soil sampling cylinders for soil pit

===At Site===
* duct seal for all connections
* soil pit sensors in large actionpacker

===Extras===
* think about how to mount iridium here...
*Bring covers from Fairbanks to cover unitstrut ends like tennis balls.

===Left to fix===
* Decagon SRS sensors... test again in Fairbanks
* Thermal Conductivity sensors... figure out their deal...

* Review fieldbook

Summer 2016 visit

2016-08-17T23:45:57Z

66.58.163.81:

*get tower safety trained
*CANOE out to figure all of underwater sensors out!
**measuring tape
**inspect pressure transducer and change desiccant
**figure out what is measuring temperature
**swap underwater quantum
*replace snow transducer
*remove old radio antenna
*bring longer conduit housing for evap pan
*mesh for pluvio
**bring wood, nails, hammer
*guided accuracy test pluvio
*take down TPS tripod
*take out base station for old radio? ask jim first- he said ok
*fix snow depth output/program, right now snow_depth_1 and temp_corr are basically the same and not usefully different
*BRING PLUVIO USB CABLE
*ANTIFREEZE for pluvio

Oliktok precip site

2016-08-16T08:18:52Z

66.58.163.81: /* Oliktok */

===Barrow site===
Has:
*Enclosure
*CR1000
*Judd or SR50a
*Radios/NL100

Needs:
*LPM
*Quadpod for:
*3x SR50a

===Atqasuk===
Uninstalling:
*Nipher guage
*CR1000
*2 radios
*Wenglor particle counter
*SR50a
*quadpod
*computer?

===Oliktok===
Installing:
*Geonor + fence
*Power AC
*SR50a on quadpod
*LPM

Geonor notes
*needs antifreeze sol'n: Propylene glycol (40%) / Methanol (60%)
*needs 0.4L Low Pour Hydraulic oil
*Geonor fence
**Alter shield
***attach shield to Geonor stand with 1in pipe, then 1in to 3/4in nurail offset cross fitting like (http://www.nurail.com/products/%2310-Offset-Cross-%252d-3%7B47%7D4in-x-1in..html), then 3/4in post provided with the alter shield
***apply rust prevention coating
Power
*LPM uses max 150 VA (VA = watts)
*Geonor heater draws 25 watts at 24 volts
**3.4 mA per vibrating wire. 7 mA on warm up
*SR50a
**250 mA peak measurement (measurement takes less than 1 sec)
**1 mA quiescent in SDI12 mode

Todo
*asked alaska steel for nurail quote, do PR when receive it
*figure out geonor fence
*figure out geonor heater
*programs
**update Barrow (downloaded one from bob's dropbox, now in docs folder)
**write new for oliktok
*LPM communication
*quadpods: order pipe and nurail fittings from alaska steel
*sensor mounts. enclosure mounts
*conduit
*zip ties (heavy duty), and little ones for the enclosure. labels for the wires in enclosure

Site Location

[[File:Location precip gauges2.PNG|800px]]

Teller Lower Station

2016-08-14T19:03:59Z

66.58.163.81:

Tape Color is '''BLUE'''

===To Bring:===

===Outstanding Items===
* Make Discharge Measurement
** Tools:
** Cloth Tape
* Need to bring out
* 1" Al pipe for away from tripod snow stand... can skinny pipe be made to work?
** Tools: 1/2" nut driver / wrench
* Declination is 11 degrees... correct this later using datapro function.
* XX use battery box tarp to flop soil pit lid onto.
** tape measure
** saw
** tarp
** shovel
* camera power
* XX terminal strips for SDI 12 devices.
* XX 1"x1ft stub for net radiation
* XX guy wires for snow stand
* mount camera
* fix program problems:
** Resistance logging
** soil temperature logging
** check to see that east 30 sensors are good with the jumper wire in place
**

====Cross Arms====
* Net Radiometer skin temperature
** need to track down unistrut & strut clamps for stabilization (or ubolts)
* small cross arm for air temperature
* RM Young should mount to top without issue.
* Precip stand is already out there
* Need to figure out where NDVI sensors point. & do we have all supplies for that...

===Sensors===
====To Bring:====
* 015103 WS/WD
** Make up cable for it
* CR200 for measuring Pressure Transducers
* ''5 pcs'' VITEL Hydraprobe II
* ''4 pcs'' East30 sensors thermal conductivity or specific heat
** also interface board
** also measure the heater resistance of each
* Cable protection
* cable ties & hose clamps for securing cabling to tripod
* VATP 1504 - see email for thermistor calibration offsets

====Sensor Heights====
* Anemometer @ top of tripod / ~3 meters
* HMP155 @ 1.5m above ground surface
* Barometric Pressure - in instrument box
* Net Radiation -
* Snow Temperature profile -- ground surface in the shrubs
* Snow Depth 1 -- 2m on cross arm off station
* Snow Depth 2 -- in shrubs on a stand.

Already at site:
* HMP155
** thinking about bringing out a replacement temperature head though because the one in place has been on the fritz over the summer.
* TE525MM
* CNR4 w/bracket
* Two Batteries
* Solar Panel
* Charge Controller

===Extras===
* think about how to mount iridium here...
*Bring covers from Fairbanks to cover unitstrut ends like tennis balls.

Teller Lower Station

2016-08-14T18:59:16Z

66.58.163.81:

Tape Color is '''BLUE'''

===To Bring:===

===Outstanding Items===
* Make Discharge Measurement
* Need to bring out
* 1" Al pipe for away from tripod snow stand... can skinny pipe be made to work?
* Declination is 11 degrees... need to correct this using datapro function.
* XX use battery box tarp to flop soil pit lid onto.
* camera power
* XX terminal strips for SDI 12 devices.
* XX 1"x1ft stub for net radiation
* XX guy wires for snow stand
* mount camera
* fix program problems:
** Resistor logging
** soil temperature logging
** check to see that east 30 sensors are good with the jumper wire in place
**

====Cross Arms====
* Net Radiometer skin temperature
** need to track down unistrut & strut clamps for stabilization (or ubolts)
* small cross arm for air temperature
* RM Young should mount to top without issue.
* Precip stand is already out there
* Need to figure out where NDVI sensors point. & do we have all supplies for that...

===Sensors===
====To Bring:====
* 015103 WS/WD
** Make up cable for it
* CR200 for measuring Pressure Transducers
* ''5 pcs'' VITEL Hydraprobe II
* ''4 pcs'' East30 sensors thermal conductivity or specific heat
** also interface board
** also measure the heater resistance of each
* Cable protection
* cable ties & hose clamps for securing cabling to tripod
* VATP 1504 - see email for thermistor calibration offsets

====Sensor Heights====
* Anemometer @ top of tripod / ~3 meters
* HMP155 @ 1.5m above ground surface
* Barometric Pressure - in instrument box
* Net Radiation -
* Snow Temperature profile -- ground surface in the shrubs
* Snow Depth 1 -- 2m on cross arm off station
* Snow Depth 2 -- in shrubs on a stand.

Already at site:
* HMP155
** thinking about bringing out a replacement temperature head though because the one in place has been on the fritz over the summer.
* TE525MM
* CNR4 w/bracket
* Two Batteries
* Solar Panel
* Charge Controller

===Extras===
* think about how to mount iridium here...
*Bring covers from Fairbanks to cover unitstrut ends like tennis balls.