IARC 207 Wiki - User contributions [en]

Kougraok M64

2017-06-03T19:31:19Z

66.58.227.13: /* Cross arm situation */

Tape Color is '''Green'''

===In NGEE Container:===
* Tripod base with green tape. '''This is in NGEE Container'''
** Requires 1.25" schedule 40 pipe mast

===In UAF Storage===
* 1" x 3' aluminum pipe, three pieces
* 2 pipe wrenches
* large cable ties
* small cable ties
* fish tape
* 4 dog anchors
* saw
* grease
* anti oxidizing grease for electrical connections
* a bunch of hose clamps (including for precip bucket
* Bosch drill
* GIPL drill bit

===Sensors in UAF storage===
* Tipping bucket
* GIPL VATP

===To Buy in Nome===
* At Grizzly Hardware pick up a 1.25" schedule 40 pipe threaded on two sides

===To buy in Fairbanks===
* 1" topper for tripod past -Lily asks what is this? ''(These two items connect RM Young anemometer to the top of the tower)''
* 1" to 1.25" coupler to replace one used at teller top site -Lily asks if we still need this?

===Cross arm situation===
* Use short 1" Aluminum pipe for precip stand at site. Have three of these in the UAF Nome storage as well as the brackets required.
* the hose clamps for the site are in Nome along with some other items.
* Bob found 4 pcs 1" cross arms on 5/30 trip. There were also some 3/4" aluminum cross arms, perhaps for precip stand.
* 1 full altershield in Nome storage but... has flange plates on bottom so we'll need to do a bit more work to get things proper.
** (Flange Plate: http://www.homedepot.com/p/1-in-Black-Malleable-Iron-Threaded-Floor-Flange-521-605HN/100179931 )

===To ship from Fairbanks===
* 2 pcs 12V batteries

===Sensors===

{| class="wikitable"
|+Sensors
|-
|instrument
|SN
|where?
|height
|cable
|mount
|crossarm
|crossarm mount
|-
|HMP155A
|
|7pcs in UAF Storage
|1.5meters
|?
|yes and shield
|na
|na
|-
|RMyoung
|
|1 pcs in UAF Storage
|3meters
|?
|in box
|in box
|Frontier supply stocks them
|-
|Barometric pressure
|
|?
|na
|?
|na
|na
|na
|-
|CNR4
|
|in box
|
|in box
|in box
|
|
|-
|3 NDVI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|3 PRI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|Skin Temp
|
|in box
|
|attached
|in box
|
|
|-
|5 soil moisture
|
|in box
|color coded, see hydraprobe notes
|attached
|na
|na
|na
|-
|4 thermal conductivity
|
|only one in box
|
|
|
|
|
|-
|VAPT
|
| UAF Storage
|
|
|
|
|
|-
|SR50a?
|
| UAF Storage... I may have stolen the transducer though...
|
|need longer cable for far one
|
|
|
|-
|tipping bucket
|
|In Nome Storage
|
|
|?
|
|
|-

|}

Hydra Probe notes
* ID 0 = 5cm = red
* ID 1 = 10cm = orange
* ID 2 = 20cm = purple
* ID 3 = 30cm = brown
* ID 4 = 40cm = black

SRS notes
*PRI up = red tape = 7 SDI address
*PRI #1 = orange = 8 SDI address
*PRI #2 = purple = 9 SDI address
*NDVI up = red tape = A SDI address
*NDVI #1 = orange = B SDI address
*NDVI #2 = purple = C SDI address
Measure resistor value and SN beforehand?

===infrastructure===
*tower
**tripod - in storage
** mast- called Grizzly 907 443 2108 to see if we can reserve one
** alter shield for tipping bucket?
*power
**solar panel
**wires for panel
**charge controller
**crips/connectors for charge controller wires
**2 big batteries
**connector wires for batteries
**wire to logger
**fuse
*Enclosure
**mount for enclosure
**logger
**mux
**wires between mux and logger
**cable
**printed program
**screw driver
**CFM100+card

===Actionpacker in uaf storage===
* Cable Ties
* 2 pipe wrenches
* hose clmaps
* three camping dinners (seafood deals)
* a bit more snacks
* fish tape
* soil samplers for teller bottom
* duct seal
* grease & anticorrosion goo
* (2) switched 12 volt control
* saw for dirt
* dog anchor
* box screw driver & serial cable (2)
* drill charger
* test radio for kougarok conenctions
** need a cigarette adapter
* hobo kit
* SR50A for K2 & K3
* 1" x 1" ubolt cross arm bracket
* 1" x 1.5" ubolt cross arm bracket
* 1" x 1" nurail cross
* 1" x 3/4" nurail cross
* LANL cameras
* bubble wrap
===General actionpacker placed into storage but may be useful for K64===
* Misc ubolts
* misc unistrut clamps (mostly wrong sizes I suspect)
* four pieces of unistrut 12-18 inches. two half size two full size
* three things of electrical tape, duct tape, rubber splicing tape
* couple NRS straps 9 & 12 feet
* 1 8GB CF card
* misc wire
* misc other
* baking soda

===Checklist for bob to find in Nome===
*Tripod kit -- Tripod is in NGEE conex
*trail mat for underneath tripod -- I'm not sure if we have any left
*Batteries for new K64 met tower -- The batteries are in room 112 in basement, or at least one, there are a couple others out there.
*tipping bucket
**hose clamps for mounting it
**cable (how long is it?)
*wind sensor
**cable
*1 SR50a sensor
**cable (how long is it?)
**mounting kit?
*Barometer
**cable
**what kind of screws do I need to mount it in the enclosure?
*VATP -- it is in Nome
**is there a resistor taped to it?
*HMP155
**cable
*sledge hammer
*shovel
*Drill for VATP
*Is Bob Bolton's sleeping bag there?
*if time: buy mast at Grizzly

Kougraok M64

2017-06-03T19:26:52Z

66.58.227.13: /* To Buy in Nome */

Tape Color is '''Green'''

===In NGEE Container:===
* Tripod base with green tape. '''This is in NGEE Container'''
** Requires 1.25" schedule 40 pipe mast

===In UAF Storage===
* 1" x 3' aluminum pipe, three pieces
* 2 pipe wrenches
* large cable ties
* small cable ties
* fish tape
* 4 dog anchors
* saw
* grease
* anti oxidizing grease for electrical connections
* a bunch of hose clamps (including for precip bucket
* Bosch drill
* GIPL drill bit

===Sensors in UAF storage===
* Tipping bucket
* GIPL VATP

===To Buy in Nome===
* At Grizzly Hardware pick up a 1.25" schedule 40 pipe threaded on two sides

===To buy in Fairbanks===
* 1" topper for tripod past -Lily asks what is this? ''(These two items connect RM Young anemometer to the top of the tower)''
* 1" to 1.25" coupler to replace one used at teller top site -Lily asks if we still need this?

===Cross arm situation===
* Use short 1" Aluminum pipe for precip stand at site. Have three of these in the UAF Nome storage as well as the brackets required.
* the hose clamps for the site are in Nome along with some other items.

===To ship from Fairbanks===
* 2 pcs 12V batteries

===Sensors===

{| class="wikitable"
|+Sensors
|-
|instrument
|SN
|where?
|height
|cable
|mount
|crossarm
|crossarm mount
|-
|HMP155A
|
|7pcs in UAF Storage
|1.5meters
|?
|yes and shield
|na
|na
|-
|RMyoung
|
|1 pcs in UAF Storage
|3meters
|?
|in box
|in box
|Frontier supply stocks them
|-
|Barometric pressure
|
|?
|na
|?
|na
|na
|na
|-
|CNR4
|
|in box
|
|in box
|in box
|
|
|-
|3 NDVI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|3 PRI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|Skin Temp
|
|in box
|
|attached
|in box
|
|
|-
|5 soil moisture
|
|in box
|color coded, see hydraprobe notes
|attached
|na
|na
|na
|-
|4 thermal conductivity
|
|only one in box
|
|
|
|
|
|-
|VAPT
|
| UAF Storage
|
|
|
|
|
|-
|SR50a?
|
| UAF Storage... I may have stolen the transducer though...
|
|need longer cable for far one
|
|
|
|-
|tipping bucket
|
|In Nome Storage
|
|
|?
|
|
|-

|}

Hydra Probe notes
* ID 0 = 5cm = red
* ID 1 = 10cm = orange
* ID 2 = 20cm = purple
* ID 3 = 30cm = brown
* ID 4 = 40cm = black

SRS notes
*PRI up = red tape = 7 SDI address
*PRI #1 = orange = 8 SDI address
*PRI #2 = purple = 9 SDI address
*NDVI up = red tape = A SDI address
*NDVI #1 = orange = B SDI address
*NDVI #2 = purple = C SDI address
Measure resistor value and SN beforehand?

===infrastructure===
*tower
**tripod - in storage
** mast- called Grizzly 907 443 2108 to see if we can reserve one
** alter shield for tipping bucket?
*power
**solar panel
**wires for panel
**charge controller
**crips/connectors for charge controller wires
**2 big batteries
**connector wires for batteries
**wire to logger
**fuse
*Enclosure
**mount for enclosure
**logger
**mux
**wires between mux and logger
**cable
**printed program
**screw driver
**CFM100+card

===Actionpacker in uaf storage===
* Cable Ties
* 2 pipe wrenches
* hose clmaps
* three camping dinners (seafood deals)
* a bit more snacks
* fish tape
* soil samplers for teller bottom
* duct seal
* grease & anticorrosion goo
* (2) switched 12 volt control
* saw for dirt
* dog anchor
* box screw driver & serial cable (2)
* drill charger
* test radio for kougarok conenctions
** need a cigarette adapter
* hobo kit
* SR50A for K2 & K3
* 1" x 1" ubolt cross arm bracket
* 1" x 1.5" ubolt cross arm bracket
* 1" x 1" nurail cross
* 1" x 3/4" nurail cross
* LANL cameras
* bubble wrap
===General actionpacker placed into storage but may be useful for K64===
* Misc ubolts
* misc unistrut clamps (mostly wrong sizes I suspect)
* four pieces of unistrut 12-18 inches. two half size two full size
* three things of electrical tape, duct tape, rubber splicing tape
* couple NRS straps 9 & 12 feet
* 1 8GB CF card
* misc wire
* misc other
* baking soda

===Checklist for bob to find in Nome===
*Tripod kit -- Tripod is in NGEE conex
*trail mat for underneath tripod -- I'm not sure if we have any left
*Batteries for new K64 met tower -- The batteries are in room 112 in basement, or at least one, there are a couple others out there.
*tipping bucket
**hose clamps for mounting it
**cable (how long is it?)
*wind sensor
**cable
*1 SR50a sensor
**cable (how long is it?)
**mounting kit?
*Barometer
**cable
**what kind of screws do I need to mount it in the enclosure?
*VATP -- it is in Nome
**is there a resistor taped to it?
*HMP155
**cable
*sledge hammer
*shovel
*Drill for VATP
*Is Bob Bolton's sleeping bag there?
*if time: buy mast at Grizzly

Kougraok M64

2017-06-03T19:25:52Z

66.58.227.13: /* Sensors */

Tape Color is '''Green'''

===In NGEE Container:===
* Tripod base with green tape. '''This is in NGEE Container'''
** Requires 1.25" schedule 40 pipe mast

===In UAF Storage===
* 1" x 3' aluminum pipe, three pieces
* 2 pipe wrenches
* large cable ties
* small cable ties
* fish tape
* 4 dog anchors
* saw
* grease
* anti oxidizing grease for electrical connections
* a bunch of hose clamps (including for precip bucket
* Bosch drill
* GIPL drill bit

===Sensors in UAF storage===
* Tipping bucket
* GIPL VATP

===To Buy in Nome===
* At Grizzly Hardware pick up a 1.25" schedule 40 pipe threaded on one side

===To buy in Fairbanks===
* 1" topper for tripod past -Lily asks what is this? ''(These two items connect RM Young anemometer to the top of the tower)''
* 1" to 1.25" coupler to replace one used at teller top site -Lily asks if we still need this?

===Cross arm situation===
* Use short 1" Aluminum pipe for precip stand at site. Have three of these in the UAF Nome storage as well as the brackets required.
* the hose clamps for the site are in Nome along with some other items.

===To ship from Fairbanks===
* 2 pcs 12V batteries

===Sensors===

{| class="wikitable"
|+Sensors
|-
|instrument
|SN
|where?
|height
|cable
|mount
|crossarm
|crossarm mount
|-
|HMP155A
|
|7pcs in UAF Storage
|1.5meters
|?
|yes and shield
|na
|na
|-
|RMyoung
|
|1 pcs in UAF Storage
|3meters
|?
|in box
|in box
|Frontier supply stocks them
|-
|Barometric pressure
|
|?
|na
|?
|na
|na
|na
|-
|CNR4
|
|in box
|
|in box
|in box
|
|
|-
|3 NDVI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|3 PRI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|Skin Temp
|
|in box
|
|attached
|in box
|
|
|-
|5 soil moisture
|
|in box
|color coded, see hydraprobe notes
|attached
|na
|na
|na
|-
|4 thermal conductivity
|
|only one in box
|
|
|
|
|
|-
|VAPT
|
| UAF Storage
|
|
|
|
|
|-
|SR50a?
|
| UAF Storage... I may have stolen the transducer though...
|
|need longer cable for far one
|
|
|
|-
|tipping bucket
|
|In Nome Storage
|
|
|?
|
|
|-

|}

Hydra Probe notes
* ID 0 = 5cm = red
* ID 1 = 10cm = orange
* ID 2 = 20cm = purple
* ID 3 = 30cm = brown
* ID 4 = 40cm = black

SRS notes
*PRI up = red tape = 7 SDI address
*PRI #1 = orange = 8 SDI address
*PRI #2 = purple = 9 SDI address
*NDVI up = red tape = A SDI address
*NDVI #1 = orange = B SDI address
*NDVI #2 = purple = C SDI address
Measure resistor value and SN beforehand?

===infrastructure===
*tower
**tripod - in storage
** mast- called Grizzly 907 443 2108 to see if we can reserve one
** alter shield for tipping bucket?
*power
**solar panel
**wires for panel
**charge controller
**crips/connectors for charge controller wires
**2 big batteries
**connector wires for batteries
**wire to logger
**fuse
*Enclosure
**mount for enclosure
**logger
**mux
**wires between mux and logger
**cable
**printed program
**screw driver
**CFM100+card

===Actionpacker in uaf storage===
* Cable Ties
* 2 pipe wrenches
* hose clmaps
* three camping dinners (seafood deals)
* a bit more snacks
* fish tape
* soil samplers for teller bottom
* duct seal
* grease & anticorrosion goo
* (2) switched 12 volt control
* saw for dirt
* dog anchor
* box screw driver & serial cable (2)
* drill charger
* test radio for kougarok conenctions
** need a cigarette adapter
* hobo kit
* SR50A for K2 & K3
* 1" x 1" ubolt cross arm bracket
* 1" x 1.5" ubolt cross arm bracket
* 1" x 1" nurail cross
* 1" x 3/4" nurail cross
* LANL cameras
* bubble wrap
===General actionpacker placed into storage but may be useful for K64===
* Misc ubolts
* misc unistrut clamps (mostly wrong sizes I suspect)
* four pieces of unistrut 12-18 inches. two half size two full size
* three things of electrical tape, duct tape, rubber splicing tape
* couple NRS straps 9 & 12 feet
* 1 8GB CF card
* misc wire
* misc other
* baking soda

===Checklist for bob to find in Nome===
*Tripod kit -- Tripod is in NGEE conex
*trail mat for underneath tripod -- I'm not sure if we have any left
*Batteries for new K64 met tower -- The batteries are in room 112 in basement, or at least one, there are a couple others out there.
*tipping bucket
**hose clamps for mounting it
**cable (how long is it?)
*wind sensor
**cable
*1 SR50a sensor
**cable (how long is it?)
**mounting kit?
*Barometer
**cable
**what kind of screws do I need to mount it in the enclosure?
*VATP -- it is in Nome
**is there a resistor taped to it?
*HMP155
**cable
*sledge hammer
*shovel
*Drill for VATP
*Is Bob Bolton's sleeping bag there?
*if time: buy mast at Grizzly

Kougraok M64

2017-06-03T19:25:29Z

66.58.227.13: /* Sensors */

Tape Color is '''Green'''

===In NGEE Container:===
* Tripod base with green tape. '''This is in NGEE Container'''
** Requires 1.25" schedule 40 pipe mast

===In UAF Storage===
* 1" x 3' aluminum pipe, three pieces
* 2 pipe wrenches
* large cable ties
* small cable ties
* fish tape
* 4 dog anchors
* saw
* grease
* anti oxidizing grease for electrical connections
* a bunch of hose clamps (including for precip bucket
* Bosch drill
* GIPL drill bit

===Sensors in UAF storage===
* Tipping bucket
* GIPL VATP

===To Buy in Nome===
* At Grizzly Hardware pick up a 1.25" schedule 40 pipe threaded on one side

===To buy in Fairbanks===
* 1" topper for tripod past -Lily asks what is this? ''(These two items connect RM Young anemometer to the top of the tower)''
* 1" to 1.25" coupler to replace one used at teller top site -Lily asks if we still need this?

===Cross arm situation===
* Use short 1" Aluminum pipe for precip stand at site. Have three of these in the UAF Nome storage as well as the brackets required.
* the hose clamps for the site are in Nome along with some other items.

===To ship from Fairbanks===
* 2 pcs 12V batteries

===Sensors===

{| class="wikitable"
|+Sensors
|-
|instrument
|SN
|where?
|height
|cable
|mount
|crossarm
|crossarm mount
|-
|HMP155A
|
|7pcs in UAF Storage
|1.5meters
|?
|yes and shield
|na
|na
|-
|RMyoung
|
|?
|3meters
|?
|in box
|in box
|Frontier supply stocks them
|-
|Barometric pressure
|
|?
|na
|?
|na
|na
|na
|-
|CNR4
|
|in box
|
|in box
|in box
|
|
|-
|3 NDVI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|3 PRI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|Skin Temp
|
|in box
|
|attached
|in box
|
|
|-
|5 soil moisture
|
|in box
|color coded, see hydraprobe notes
|attached
|na
|na
|na
|-
|4 thermal conductivity
|
|only one in box
|
|
|
|
|
|-
|VAPT
|
| UAF Storage
|
|
|
|
|
|-
|SR50a?
|
| UAF Storage... I may have stolen the transducer though...
|
|need longer cable for far one
|
|
|
|-
|tipping bucket
|
|In Nome Storage
|
|
|?
|
|
|-

|}

Hydra Probe notes
* ID 0 = 5cm = red
* ID 1 = 10cm = orange
* ID 2 = 20cm = purple
* ID 3 = 30cm = brown
* ID 4 = 40cm = black

SRS notes
*PRI up = red tape = 7 SDI address
*PRI #1 = orange = 8 SDI address
*PRI #2 = purple = 9 SDI address
*NDVI up = red tape = A SDI address
*NDVI #1 = orange = B SDI address
*NDVI #2 = purple = C SDI address
Measure resistor value and SN beforehand?

===infrastructure===
*tower
**tripod - in storage
** mast- called Grizzly 907 443 2108 to see if we can reserve one
** alter shield for tipping bucket?
*power
**solar panel
**wires for panel
**charge controller
**crips/connectors for charge controller wires
**2 big batteries
**connector wires for batteries
**wire to logger
**fuse
*Enclosure
**mount for enclosure
**logger
**mux
**wires between mux and logger
**cable
**printed program
**screw driver
**CFM100+card

===Actionpacker in uaf storage===
* Cable Ties
* 2 pipe wrenches
* hose clmaps
* three camping dinners (seafood deals)
* a bit more snacks
* fish tape
* soil samplers for teller bottom
* duct seal
* grease & anticorrosion goo
* (2) switched 12 volt control
* saw for dirt
* dog anchor
* box screw driver & serial cable (2)
* drill charger
* test radio for kougarok conenctions
** need a cigarette adapter
* hobo kit
* SR50A for K2 & K3
* 1" x 1" ubolt cross arm bracket
* 1" x 1.5" ubolt cross arm bracket
* 1" x 1" nurail cross
* 1" x 3/4" nurail cross
* LANL cameras
* bubble wrap
===General actionpacker placed into storage but may be useful for K64===
* Misc ubolts
* misc unistrut clamps (mostly wrong sizes I suspect)
* four pieces of unistrut 12-18 inches. two half size two full size
* three things of electrical tape, duct tape, rubber splicing tape
* couple NRS straps 9 & 12 feet
* 1 8GB CF card
* misc wire
* misc other
* baking soda

===Checklist for bob to find in Nome===
*Tripod kit -- Tripod is in NGEE conex
*trail mat for underneath tripod -- I'm not sure if we have any left
*Batteries for new K64 met tower -- The batteries are in room 112 in basement, or at least one, there are a couple others out there.
*tipping bucket
**hose clamps for mounting it
**cable (how long is it?)
*wind sensor
**cable
*1 SR50a sensor
**cable (how long is it?)
**mounting kit?
*Barometer
**cable
**what kind of screws do I need to mount it in the enclosure?
*VATP -- it is in Nome
**is there a resistor taped to it?
*HMP155
**cable
*sledge hammer
*shovel
*Drill for VATP
*Is Bob Bolton's sleeping bag there?
*if time: buy mast at Grizzly

Kougraok M64

2017-06-03T19:23:01Z

66.58.227.13: /* To Buy in Nome */

Tape Color is '''Green'''

===In NGEE Container:===
* Tripod base with green tape. '''This is in NGEE Container'''
** Requires 1.25" schedule 40 pipe mast

===In UAF Storage===
* 1" x 3' aluminum pipe, three pieces
* 2 pipe wrenches
* large cable ties
* small cable ties
* fish tape
* 4 dog anchors
* saw
* grease
* anti oxidizing grease for electrical connections
* a bunch of hose clamps (including for precip bucket
* Bosch drill
* GIPL drill bit

===Sensors in UAF storage===
* Tipping bucket
* GIPL VATP

===To Buy in Nome===
* At Grizzly Hardware pick up a 1.25" schedule 40 pipe threaded on one side

===To buy in Fairbanks===
* 1" topper for tripod past -Lily asks what is this? ''(These two items connect RM Young anemometer to the top of the tower)''
* 1" to 1.25" coupler to replace one used at teller top site -Lily asks if we still need this?

===Cross arm situation===
* Use short 1" Aluminum pipe for precip stand at site. Have three of these in the UAF Nome storage as well as the brackets required.
* the hose clamps for the site are in Nome along with some other items.

===To ship from Fairbanks===
* 2 pcs 12V batteries

===Sensors===

{| class="wikitable"
|+Sensors
|-
|instrument
|SN
|where?
|height
|cable
|mount
|crossarm
|crossarm mount
|-
|HMP155A
|
|?
|1.5meters
|?
|yes and shield
|na
|na
|-
|RMyoung
|
|?
|3meters
|?
|in box
|in box
|Frontier supply stocks them
|-
|Barometric pressure
|
|?
|na
|?
|na
|na
|na
|-
|CNR4
|
|in box
|
|in box
|in box
|
|
|-
|3 NDVI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|3 PRI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|Skin Temp
|
|in box
|
|attached
|in box
|
|
|-
|5 soil moisture
|
|in box
|color coded, see hydraprobe notes
|attached
|na
|na
|na
|-
|4 thermal conductivity
|
|only one in box
|
|
|
|
|
|-
|VAPT
|
|hopefully in nome?
|
|
|
|
|
|-
|SR50a?
|
|?only one in box
|
|need longer cable for far one
|
|
|
|-
|tipping bucket
|
|hopefully in nome?
|
|
|?
|
|
|-

|}

Hydra Probe notes
* ID 0 = 5cm = red
* ID 1 = 10cm = orange
* ID 2 = 20cm = purple
* ID 3 = 30cm = brown
* ID 4 = 40cm = black

SRS notes
*PRI up = red tape = 7 SDI address
*PRI #1 = orange = 8 SDI address
*PRI #2 = purple = 9 SDI address
*NDVI up = red tape = A SDI address
*NDVI #1 = orange = B SDI address
*NDVI #2 = purple = C SDI address
Measure resistor value and SN beforehand?

===infrastructure===
*tower
**tripod - in storage
** mast- called Grizzly 907 443 2108 to see if we can reserve one
** alter shield for tipping bucket?
*power
**solar panel
**wires for panel
**charge controller
**crips/connectors for charge controller wires
**2 big batteries
**connector wires for batteries
**wire to logger
**fuse
*Enclosure
**mount for enclosure
**logger
**mux
**wires between mux and logger
**cable
**printed program
**screw driver
**CFM100+card

===Actionpacker in uaf storage===
* Cable Ties
* 2 pipe wrenches
* hose clmaps
* three camping dinners (seafood deals)
* a bit more snacks
* fish tape
* soil samplers for teller bottom
* duct seal
* grease & anticorrosion goo
* (2) switched 12 volt control
* saw for dirt
* dog anchor
* box screw driver & serial cable (2)
* drill charger
* test radio for kougarok conenctions
** need a cigarette adapter
* hobo kit
* SR50A for K2 & K3
* 1" x 1" ubolt cross arm bracket
* 1" x 1.5" ubolt cross arm bracket
* 1" x 1" nurail cross
* 1" x 3/4" nurail cross
* LANL cameras
* bubble wrap
===General actionpacker placed into storage but may be useful for K64===
* Misc ubolts
* misc unistrut clamps (mostly wrong sizes I suspect)
* four pieces of unistrut 12-18 inches. two half size two full size
* three things of electrical tape, duct tape, rubber splicing tape
* couple NRS straps 9 & 12 feet
* 1 8GB CF card
* misc wire
* misc other
* baking soda

===Checklist for bob to find in Nome===
*Tripod kit -- Tripod is in NGEE conex
*trail mat for underneath tripod -- I'm not sure if we have any left
*Batteries for new K64 met tower -- The batteries are in room 112 in basement, or at least one, there are a couple others out there.
*tipping bucket
**hose clamps for mounting it
**cable (how long is it?)
*wind sensor
**cable
*1 SR50a sensor
**cable (how long is it?)
**mounting kit?
*Barometer
**cable
**what kind of screws do I need to mount it in the enclosure?
*VATP -- it is in Nome
**is there a resistor taped to it?
*HMP155
**cable
*sledge hammer
*shovel
*Drill for VATP
*Is Bob Bolton's sleeping bag there?
*if time: buy mast at Grizzly

Kougraok M64

2017-06-03T19:22:07Z

66.58.227.13: /* In NGEE Container: */

Tape Color is '''Green'''

===In NGEE Container:===
* Tripod base with green tape. '''This is in NGEE Container'''
** Requires 1.25" schedule 40 pipe mast

===In UAF Storage===
* 1" x 3' aluminum pipe, three pieces
* 2 pipe wrenches
* large cable ties
* small cable ties
* fish tape
* 4 dog anchors
* saw
* grease
* anti oxidizing grease for electrical connections
* a bunch of hose clamps (including for precip bucket
* Bosch drill
* GIPL drill bit

===Sensors in UAF storage===
* Tipping bucket
* GIPL VATP

===To Buy in Nome===
* At Grizzly Hardware pick up a 1.25" schedule 40 pipe threaded on one side

===To buy in Fairbanks
* 1" topper for tripod past -Lily asks what is this?
* 1" to 1.25" coupler to replace one used at teller top site -Lily asks if we still need this?

===Cross arm situation===
* Use short 1" Aluminum pipe for precip stand at site. Have three of these in the UAF Nome storage as well as the brackets required.
* the hose clamps for the site are in Nome along with some other items.

===To ship from Fairbanks===
* 2 pcs 12V batteries

===Sensors===

{| class="wikitable"
|+Sensors
|-
|instrument
|SN
|where?
|height
|cable
|mount
|crossarm
|crossarm mount
|-
|HMP155A
|
|?
|1.5meters
|?
|yes and shield
|na
|na
|-
|RMyoung
|
|?
|3meters
|?
|in box
|in box
|Frontier supply stocks them
|-
|Barometric pressure
|
|?
|na
|?
|na
|na
|na
|-
|CNR4
|
|in box
|
|in box
|in box
|
|
|-
|3 NDVI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|3 PRI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|Skin Temp
|
|in box
|
|attached
|in box
|
|
|-
|5 soil moisture
|
|in box
|color coded, see hydraprobe notes
|attached
|na
|na
|na
|-
|4 thermal conductivity
|
|only one in box
|
|
|
|
|
|-
|VAPT
|
|hopefully in nome?
|
|
|
|
|
|-
|SR50a?
|
|?only one in box
|
|need longer cable for far one
|
|
|
|-
|tipping bucket
|
|hopefully in nome?
|
|
|?
|
|
|-

|}

Hydra Probe notes
* ID 0 = 5cm = red
* ID 1 = 10cm = orange
* ID 2 = 20cm = purple
* ID 3 = 30cm = brown
* ID 4 = 40cm = black

SRS notes
*PRI up = red tape = 7 SDI address
*PRI #1 = orange = 8 SDI address
*PRI #2 = purple = 9 SDI address
*NDVI up = red tape = A SDI address
*NDVI #1 = orange = B SDI address
*NDVI #2 = purple = C SDI address
Measure resistor value and SN beforehand?

===infrastructure===
*tower
**tripod - in storage
** mast- called Grizzly 907 443 2108 to see if we can reserve one
** alter shield for tipping bucket?
*power
**solar panel
**wires for panel
**charge controller
**crips/connectors for charge controller wires
**2 big batteries
**connector wires for batteries
**wire to logger
**fuse
*Enclosure
**mount for enclosure
**logger
**mux
**wires between mux and logger
**cable
**printed program
**screw driver
**CFM100+card

===Actionpacker in uaf storage===
* Cable Ties
* 2 pipe wrenches
* hose clmaps
* three camping dinners (seafood deals)
* a bit more snacks
* fish tape
* soil samplers for teller bottom
* duct seal
* grease & anticorrosion goo
* (2) switched 12 volt control
* saw for dirt
* dog anchor
* box screw driver & serial cable (2)
* drill charger
* test radio for kougarok conenctions
** need a cigarette adapter
* hobo kit
* SR50A for K2 & K3
* 1" x 1" ubolt cross arm bracket
* 1" x 1.5" ubolt cross arm bracket
* 1" x 1" nurail cross
* 1" x 3/4" nurail cross
* LANL cameras
* bubble wrap
===General actionpacker placed into storage but may be useful for K64===
* Misc ubolts
* misc unistrut clamps (mostly wrong sizes I suspect)
* four pieces of unistrut 12-18 inches. two half size two full size
* three things of electrical tape, duct tape, rubber splicing tape
* couple NRS straps 9 & 12 feet
* 1 8GB CF card
* misc wire
* misc other
* baking soda

===Checklist for bob to find in Nome===
*Tripod kit -- Tripod is in NGEE conex
*trail mat for underneath tripod -- I'm not sure if we have any left
*Batteries for new K64 met tower -- The batteries are in room 112 in basement, or at least one, there are a couple others out there.
*tipping bucket
**hose clamps for mounting it
**cable (how long is it?)
*wind sensor
**cable
*1 SR50a sensor
**cable (how long is it?)
**mounting kit?
*Barometer
**cable
**what kind of screws do I need to mount it in the enclosure?
*VATP -- it is in Nome
**is there a resistor taped to it?
*HMP155
**cable
*sledge hammer
*shovel
*Drill for VATP
*Is Bob Bolton's sleeping bag there?
*if time: buy mast at Grizzly

2017 NGEE June Nome Trip

2017-06-03T19:20:11Z

66.58.227.13:

* @ [[Kougraok M64]]
** soil pit (fall deployment)
*** soil moisture @ 5, 10, 20, 30, 40 cm bgs
** soil thermal conductivity @ 10, 20, 30, 40 cm bgs
** soil temperature @ 10, 20, 30, 40 cm bgs
**** soil heat flux near base of active layer & plant / soil boundary
*** 1.5m soil temperature profile
*** snow depth @ tripod
*** snow depth away from tripod
*** interval camera
*** 4 component radiation
*** Spectral response sensors: NDVI & PRI up looking and two vegetation communities
*** 1.5m Air temperature, Relative Humidity, & Dew Point Temperature
*** Wind speed and direction at 3m
*** summer precipitation
* @ Teller Bottom
** send one more program to fix 5cm bgs soil moisture out of range array error

Old Atlas sites:
* @ C1 Grid
** We have a CNR4 for this site I believe.
** HMP155 has been changed out here
** fix MRC portion of program last change we screwed something up and sent the 2011 program with a but rather than the 2012 version.
* @ C2 Blueberry
** Replace the LW Transmitted cable, will need to bring the whole package from Fairbanks
** 10meter AT/RH has not worked since 2011
* @anvil scool
**propeller for wind sensor

===bring===
**radios to download K sites remotely if necessary
**copies of permits?
**radios for base station (in basement)
**drill bit for VAPT probe
**zip ties
**hose clamps
**TOOL BAGS
**CABLE BAG
**putty
**resistor for VAPT
**fish tape
**measuring tape
**anti corrosion goo
**extra nuts, washers, etc
**extra ubolts
**guy wire and findings
**inReach, sat phone
**sledge hammer
**sleeping bag liner?
**torpedo and circle level
**CFM100+card
**field books, pencils, pens sharpies
**duct tape
**splicing tape
**electrical tape

===todo===
**Bob: figure out base radio in Nome
**book housing: campsite? NPS bunkhouse: 1800.471.2352 or go downtown their office is the Sitnasauk building on front street?
**ship things
**find all the stuff for tower
**look@ data bob recently downloaded from teller
**look at data streaming in on NGEE data
**which sites need new batteries?
**replace wire on solar panel?
**wire up box
**figure out cross arms
**Do i need two mux's?
**make list for bob to look for in UAF storage (trail matt?, hose clamps for tipping bucket, tripod, buy mast if have time, batteries)
**TA's
**find other sr50a
**safety plan

===to buy===
*Alaska Steel
**threaded coupler for 1 to 1.25 pipe for Wind sensor
**cross arms (8ft rad[nurailT], 5 ft tower snow[nurailT], 4,4,5,3 ft far snow[3nurailT], 4,4,3ft tipping[2nurailT], 5 ft far rad
***7nurail 1.25 T fittings, 8ft, 3*5ft, 4*4ft, 2*3ft
**nurail fittings
*campbell
**2 new propellers (1 for anvil school, 1 for teller top)
**20 SR50a transducers
**CNR4 desiccant. how many (Teller top, teller bottom, 4 in barrow)?
**CFM
**long SR50a cable
*home depot
**conduit
**fuse and holder
**tennis balls or something to cover pokey objects
*** Rebar protection, found at AIH, sometimes home depot but didn't see anything in May when I was looking
**rebar/screed stakes
**guy wire and findings

*metric handheld flow rod

===for camping===
* WATER
** water jug in nome storage
*Tents, sleeping bags, sleeping pads
** Tent is in room 112
** sleeping pads are in uaf storage
** sleeping bag are in uaf storage
* Stove
** propane stove in nome storage
*Food

Kougraok M64

2017-05-30T05:39:47Z

66.58.227.13: /* Checklist for bob to find in Nome */

Tape Color is '''Green'''

===In NGEE Container:===
* Tripod base with green tape. -Lily remembers bob said this was in Nome, is this correct?
** Requires 1.25" schedule 40 pipe mast

===In UAF Storage===
* 1" x 3' aluminum pipe, three pieces
* 2 pipe wrenches
* large cable ties
* small cable ties
* fish tape
* 4 dog anchors
* saw
* grease
* anti oxidizing grease for electrical connections
* a bunch of hose clamps (including for precip bucket
* Bosch drill
* GIPL drill bit

===Sensors in UAF storage===
* Tipping bucket
* GIPL VATP

===To Buy in Nome===
* At Grizzly Hardware pick up a 1.25" schedule 40 pipe threaded on one side

===To buy in Fairbanks
* 1" topper for tripod past -Lily asks what is this?
* 1" to 1.25" coupler to replace one used at teller top site -Lily asks if we still need this?

===Cross arm situation===
* Use short 1" Aluminum pipe for precip stand at site. Have three of these in the UAF Nome storage as well as the brackets required.
* the hose clamps for the site are in Nome along with some other items.

===To ship from Fairbanks===
* 2 pcs 12V batteries

===Sensors===

{| class="wikitable"
|+Sensors
|-
|instrument
|SN
|where?
|height
|cable
|mount
|crossarm
|crossarm mount
|-
|HMP155A
|
|?
|1.5meters
|?
|yes and shield
|na
|na
|-
|RMyoung
|
|?
|3meters
|?
|in box
|in box
|Frontier supply stocks them
|-
|Barometric pressure
|
|?
|na
|?
|na
|na
|na
|-
|CNR4
|
|in box
|
|in box
|in box
|
|
|-
|3 NDVI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|3 PRI sensors
|
|in box
|color coded, see SRS notes
|attached
|in box
|
|
|-
|Skin Temp
|
|in box
|
|attached
|in box
|
|
|-
|5 soil moisture
|
|in box
|color coded, see hydraprobe notes
|attached
|na
|na
|na
|-
|4 thermal conductivity
|
|only one in box
|
|
|
|
|
|-
|VAPT
|
|hopefully in nome?
|
|
|
|
|
|-
|SR50a?
|
|?only one in box
|
|need longer cable for far one
|
|
|
|-
|tipping bucket
|
|hopefully in nome?
|
|
|?
|
|
|-

|}

Hydra Probe notes
* ID 0 = 5cm = red
* ID 1 = 10cm = orange
* ID 2 = 20cm = purple
* ID 3 = 30cm = brown
* ID 4 = 40cm = black

SRS notes
*PRI up = red tape = 7 SDI address
*PRI #1 = orange = 8 SDI address
*PRI #2 = purple = 9 SDI address
*NDVI up = red tape = A SDI address
*NDVI #1 = orange = B SDI address
*NDVI #2 = purple = C SDI address
Measure resistor value and SN beforehand?

===infrastructure===
*tower
**tripod - in storage
** mast- called Grizzly 907 443 2108 to see if we can reserve one
** alter shield for tipping bucket?
*power
**solar panel
**wires for panel
**charge controller
**crips/connectors for charge controller wires
**2 big batteries
**connector wires for batteries
**wire to logger
**fuse
*Enclosure
**mount for enclosure
**logger
**mux
**wires between mux and logger
**cable
**printed program
**screw driver
**CFM100+card

===Actionpacker in uaf storage===
* Cable Ties
* 2 pipe wrenches
* hose clmaps
* three camping dinners (seafood deals)
* a bit more snacks
* fish tape
* soil samplers for teller bottom
* duct seal
* grease & anticorrosion goo
* (2) switched 12 volt control
* saw for dirt
* dog anchor
* box screw driver & serial cable (2)
* drill charger
* test radio for kougarok conenctions
** need a cigarette adapter
* hobo kit
* SR50A for K2 & K3
* 1" x 1" ubolt cross arm bracket
* 1" x 1.5" ubolt cross arm bracket
* 1" x 1" nurail cross
* 1" x 3/4" nurail cross
* LANL cameras
* bubble wrap
===General actionpacker placed into storage but may be useful for K64===
* Misc ubolts
* misc unistrut clamps (mostly wrong sizes I suspect)
* four pieces of unistrut 12-18 inches. two half size two full size
* three things of electrical tape, duct tape, rubber splicing tape
* couple NRS straps 9 & 12 feet
* 1 8GB CF card
* misc wire
* misc other
* baking soda

===Checklist for bob to find in Nome===
*Tripod kit -- Tripod is in NGEE conex
*trail mat for underneath tripod -- I'm not sure if we have any left
*Batteries for new K64 met tower -- The batteries are in room 112 in basement, or at least one, there are a couple others out there.
*tipping bucket
**hose clamps for mounting it
**cable (how long is it?)
*wind sensor
**cable
*1 SR50a sensor
**cable (how long is it?)
**mounting kit?
*Barometer
**cable
**what kind of screws do I need to mount it in the enclosure?
*VATP -- it is in Nome
**is there a resistor taped to it?
*HMP155
**cable
*sledge hammer
*shovel
*Drill for VATP
*Is Bob Bolton's sleeping bag there?
*if time: buy mast at Grizzly

Field Safety

2017-05-30T05:06:48Z

66.58.227.13:

==Compliance==
Before you head out into the back country for field work UAF requires completion of this Remote travel emergency plan. I'm not sure current rules on this but IARC requires submitting this with the Travel Authorization. This document should be considered the minimum though (It is for your safety and also OSHA / other regulatory compliance). Feel free to supplement with additional documentation.
* http://uaf.edu/safety/risk-management/travel/Remote-Travel-Emergency-Plan-UAF.pdf
** (If that link doesn't work look for it on this page:)
** http://uaf.edu/safety/risk-management/travel
We at IARC have a pretty solid document (I'd like to think) that goes above and beyond the UAF minimum that isn't posted here but is definitely shareable. I might post at some point the document scrubbed free of personal info or just ask Bob if you'd like to review it.

==General==
For people who aren't able to attend the Learn To Return etc. safety workshops, here are some links that are another way to get some of the information.

==Worthy Training Goals==
* Annual Bear Safety Training & certification
* Annual CPR Training & certification
* Basic First aid or wilderness first aid every 3 years & certification
* Swiftwater Rescue & certification
* If you have had first aid or wilderness first aid training, you might think about picking up a corresponding ebook on the topic. Save the book to your phone and you will have an often with you handy pocket reference.

==Aviation Safety==
Broken out into its own article: [[Aviation Safety]]

==Survival Gear==
* [[2 Person Helicopter Survival Bag]]

==Bear Safety==

A fish and Game video:
* http://www.youtube.com/watch?v=LM0OghpVaFY
* National Park Service bear spray web site:
** https://www.nps.gov/articles/bear-spray-training.htm
* Alaska Fish and Game Bear Essentials site:
** http://www.adfg.alaska.gov/?adfg=livingwithbears.bearcountry
A video licensed for viewing (I think) by the Department of Energy about Polar Bear safety:
* https://www.youtube.com/watch?v=qYnIk0ksfM4&feature=player_embedded
A paper on defensive use with pepper spray that is pretty good:
* http://wdfw.wa.gov/hunting/bear_cougar/bear/files/JWM_BearSprayAlaska.pdf
The references at the end of this Wikipedia page about bear spray are solid:
* https://en.wikipedia.org/wiki/Bear_spray
You may also know someone who has taken offline training and has material you can review like course notes from a Learn To Return class or a Joe Nava class.

===Bear Safety Commercial DVDs===
* Polar Bears: A Guide to Safety -- http://www.macecanada.com/canada/product/polar_video2.htm
* Working in Bear Country -- http://www.macecanada.com/canada/product/video2.htm
* From the bear country family of videos, a pepper spray shot: http://www.youtube.com/watch?v=CWnACum4SJs&feature=related

==Shotgun Safety==
Before you can check out a gun to take into the field you will need to take a shotgun safety course.
* The minimum frequency varies by department but if you are not comfortable around or using a shotgun then I would suggest you take the shotgun and bear safety class annually until you are familiar with the safe operation of firearms and are able to consistently conduct your self in a careful manner in their presence.
* In Fairbanks Joe Nava teaches a shotugn safety / bear safety course
* In Anchorage the Learn to Return group teaches shotgun safety and comes to Fairbanks irregularly
* The NRA can also supply you with additional instructors (if you aren't living in Fairbanks for example)

==ATV Safety==
Some decent videos here:
* http://www.youtube.com/user/ATVsafetyinstitute?feature=watch
A US Government website about safe ATV use:
* http://www.cpsc.gov/en/Safety-Education/Safety-Education-Centers/ATV-Safety-Information-Center/
A safety course, recommended for all users:
* https://cbt.svia.org/moodle/login/index.php

==Snowmachine Safety==
Some of these are a bit dated but the concepts are for the most part good. 
Skidoo / Bombardier Snowmobile safety:
* http://www.youtube.com/watch?v=aXgY1aaIx9Y 
Arctic Cat Snowmobile Safety (skip ahead to 2:18 to get through the cartoon start if it annoys you), first of three videos in the Arctic Cat film:
* http://youtu.be/d-T7IV7evxQ 
Lounsbury Snowmachine Safety website:
* http://www.lounsburyinc.com/snowmachinesafety/
* There is a short section in the ASH handbook too.

==Cold Injuries==

A key concept for cold injury prevention is exposure time. What is acceptable clothing for 10 minutes at -20F will obviously differ compared to 3 hours at -20F or 8 hours at 0F. You should also take your activity level into account. 3 moderately active hours such as a continuous snow-survey at -20F will require less clothing than say, a stand around type activity such as watching an operator drill holes in the ice or snow.

As far as medical awareness, these two documents are a good starting point:
* A good first reference from OSHA: [https://www.osha.gov/SLTC/emergencypreparedness/guides/cold.html]
* A second reference from the Army: [https://ke.army.mil/bordeninstitute/published_volumes/harshEnv1/Ch15-NonfreezingColdInjury.pdf NonFreezing Cold Injury]

For more on clothing choices and situations, here are some classic Army videos (some are better than others) and videos from other sources:
* http://www.youtube.com/watch?v=ndU2gQ716j0&feature=related
* http://www.youtube.com/watch?v=tIY8fbtu_3E&feature=relmfu
* http://www.youtube.com/watch?v=J06qjb-iIqE
* http://www.youtube.com/watch?v=ca2P-UMuYts&feature=relmfu

===Hypothermia===
'''''From Wikipedia:''''' 
'''Mild''' 
''Symptoms of mild hypothermia may be vague with sympathetic nervous system excitation (shivering, hypertension, tachycardia, tachypnea, and vasoconstriction). These are all physiological responses to preserve heat. Cold diuresis, mental confusion, as well as hepatic dysfunction may also be present. Hyperglycemia may be present, as glucose consumption by cells and insulin secretion both decrease, and tissue sensitivity to insulin may be blunted. Sympathetic activation also releases glucose from the liver. In many cases, however, especially in alcoholic patients, hypoglycemia appears to be a more common presentation. Hypoglycemia is also found in many hypothermic patients because hypothermia often is a result of hypoglycemia.'' 
'''Moderate''' 
''Low body temperature results in shivering becoming more violent. Muscle mis-coordination becomes apparent. Movements are slow and labored, accompanied by a stumbling pace and mild confusion, although the victim may appear alert. Surface blood vessels contract further as the body focuses its remaining resources on keeping the vital organs warm. The victim becomes pale. Lips, ears, fingers and toes may become blue.'' 
'''Severe''' 
''As the temperature decreases further physiological systems falter and heart rate, respiratory rate, and blood pressure all decreases. This results in an expected HR in the 30s with a temperature of 28 °C (82 °F).
Difficulty in speaking, sluggish thinking, and amnesia start to appear; inability to use hands and stumbling is also usually present. Cellular metabolic processes shut down. Below 30 °C (86 °F), the exposed skin becomes blue and puffy, muscle coordination becomes very poor, walking becomes almost impossible, and the person exhibits incoherent/irrational behavior including terminal burrowing or even a stupor. Pulse and respiration rates decrease significantly, but fast heart rates (ventricular tachycardia, atrial fibrillation) can occur. Major organs fail. Clinical death occurs. Because of decreased cellular activity in stage 3 hypothermia, the body will actually take longer to undergo brain death.'' 
'''Youtube Links:'''
* http://www.youtube.com/watch?v=2aHCfU8xur8&feature=related
* http://www.youtube.com/watch?v=2dodsozxoiA&feature=related (A bit dated information-wise at this point and more focused on water hypothermia but should give a good foundation((fast forward to 6 minutes for symptoms)) )
* http://www.youtube.com/watch?v=Bg5IaDB71oQ
* http://www.youtube.com/watch?v=FrwsXcVFd4o

===Frostbite===
'''''From Wikipedia:''''' 
''At or below 0 °C (32 °F), blood vessels close to the skin start to constrict, and blood is shunted away from the extremities via the action of glomus bodies. The same response may also be a result of exposure to high winds. This constriction helps to preserve core body temperature. In extreme cold, or when the body is exposed to cold for long periods, this protective strategy can reduce blood flow in some areas of the body to dangerously low levels. This lack of blood leads to the eventual freezing and death of skin tissue in the affected areas. There are four degrees of frostbite. Each of these degrees has varying degrees of pain.'' 
'''First degree''' 
''This is called frostnip and this only affects the surface skin, which is frozen. On the onset, there is itching and pain, and then the skin develops white, red, and yellow patches and becomes numb. The area affected by frostnip usually does not become permanently damaged as only the skin's top layers are affected. Long-term insensitivity to both heat and cold can sometimes happen after suffering from frostnip.'' 
'''Second degree''' 
''If freezing continues, the skin may freeze and harden, but the deep tissues are not affected and remain soft and normal. Second-degree injury usually blisters 1–2 days after becoming frozen. The blisters may become hard and blackened, but usually appear worse than they are. Most of the injuries heal in one month, but the area may become permanently insensitive to both heat and cold.'' 
'''Third and fourth degrees''' 
''If the area freezes further, deep frostbite occurs. The muscles, tendons, blood vessels, and nerves all freeze. The skin is hard, feels waxy, and use of the area is lost temporarily, and in severe cases, permanently. The deep frostbite results in areas of purplish blisters which turn black and which are generally blood-filled. Nerve damage in the area can result in a loss of feeling. This extreme frostbite may result in fingers and toes being amputated if the area becomes infected with gangrene. If the frostbite has gone on untreated, they may fall off. The extent of the damage done to the area by the freezing process of the frostbite may take several months to assess, and this often delays surgery to remove the dead tissue.'' 
'''Youtube Links:'''
* http://www.youtube.com/watch?v=4itZQwoR-kc&feature=related (good overview)
* http://www.youtube.com/watch?v=p4jOo4x_hDk&feature=related (Recognizing frostbite)
* http://www.youtube.com/watch?v=p17NmmARxEI&feature=relmfu (Treating frostbite)
* http://www.youtube.com/watch?v=yn2dPV0tsig&feature=related (Another good treating frostbite video)

==Cold Water Safety==
''(Less time invested in this section)'' 
''Youtube Links:''
* Cold water safety : http://www.youtube.com/watch?v=yYDASDLcJ28&feature=related
* Ice thickness check : http://www.youtube.com/watch?v=Din2V5BW0Dk
* Dunker : http://www.youtube.com/watch?v=oLqXlEGxXxo&feature=related
* Another Dunker: http://www.youtube.com/watch?v=1EHFwl9BYQM&feature=related

==Other==
If you've never filled a backpack before or aren't sure where to get started on how to fill your daypack for a day in the field here are a couple of youtubes:
* http://www.youtube.com/watch?v=foliCq-W2yE&feature=related
* http://www.youtube.com/watch?v=Cm3jISWuVb0&feature=related

Another good item is the Alaska Safety Handbook, co-written by ConocoPhillips Alaska, Eni Petroleum, ExxonMobil, Pioneer Natural Resources Alaska, Shell Exploration & Appraisal here's a link to the 2010 edition:
* Alaska Safety Handbook -- http://www.nstc.apicc.org/download/19.pdf

UAF Safety site
* http://www.uaf.edu/safety/training/

2017 NGEE March Nome Trip

2017-03-17T18:14:58Z

66.58.227.13: /* Helicopter Safety Gear */

Just a skeleton of a beginning but wanted a place to collect scraps of ideas etc.

====To Do Yet====
* Finalize Helicopter Safety Plan
* Make sure GPS systems are compatible between groups
* Decide if PDF Maps is worth purchasing or if an alternative is better
* 3/18/2017: Call Builders Industrial Supply to order 5/8" rebar

===To Purchase===
* fieldbooks
* rebar
*

===Helicopter Safety Gear===
* one tent in Fairbanks, one tent in Nome storage
* 2 solid fuel cooking stoves in Fairbanks
** fuel will arrive on NAC separately
* 5-6 emergency bivys (2 two person units)
* 2x cook pot
* 2x firestarter in fairbanks for shipping
* 2x same for sparkers
* 2x sleeping pad in fairbanks for shipping
* 2x sleeping pad in nome storage
* 2x sleeping bags in nome storage
* 2x sleeping bags in fairbanks for shipping
* 1x wood saw in fairbanks for shipping
* 1x wood hatchet in fairbanks for shipping
*

===Shipping===
====First Shipment====
* XX Check with Brian Lu on the Hazmat
====Second Shipment====
* 3 Helicopter Helmet Box
* 3pcs PVX1040T Batteries from Room 112 w/ paperwork printed from website
** Link to safety info on batteries that needs printing:
** http://www.sunxtender.com/pdfs/Sun_Xtender_Battery_Technical_Manual.pdf
** Please print Page 13 of the pdf
** Also this page: http://www.sunxtender.com/transportation.php
** Four copies total: 1 per battery and one for NAC
* Orange Snow Poles from Room 106 (3 bundles, maybe 15 poles per bundle)
* crockpot
* 1 new snow tube, 1 old snow tube
* Actionpacker #1
** 80+ deadman anchor wire
** 80+ deadman anchor wooden stake
** 80+ deadman anchor chain (Handy Link Chain Size #135)
** 80+ deadman anchor 1/8" quick link
** 20+ grounding rod nuts
** Black Electrical Tape
** 1/2" Wrench
** flat file
** round file
** 1" bit for hamer Drill
* 20 boxed stop signs
* Bob's Skis &polk poles
* tobogan sled
* 3 pcs Survey Tripods
* AP # 2 clothes
* AP # 3
** boots
** thermal conductivity probe
** refrigewear
** 4x snowmetrics

====Campus and Not quite ready====
* final walk through of office

====At Bob's House and Ready to load====

====Bob's House Not Ready====
* WInter Clothes etc
* Survival / safety actionpacker
* ATV helmets
* package of AA batteries above chocolate stash between Bob and Ross
* orange / white survey rods

===Things to ship===
* Solar Panels for radio repeater
* large actionpacker with snow survey supplies
* Most likely Bob's trip gear
* battery charger
* rest of gps repeater system

===Aurora Vehicle Reservation===
* 3/20 to 4/7 SUV
* Reservation: R40294

===General Snow Survey Gear===
* shovels (nome Storage)
* XX 2x Thermal Conductivity Probes
* XX 2x Snow density tube
* Going AK Air 1x magnaprobe
* Lots of labeled ziplocs
* 2x * snow scale
* short power point on snow survey techniques
* one pager for fieldbooks on what to do
* XX 4 pairs of snow shoes plus one pair of skis
* XX small sled (can haul out by snowmachine on the 21st and leave for our use the rest of the time)
* small actionpacker
* --> at campus still --> radios so groups can maintain contact
* XX satellite phone
* XX satellite tracker
* XX Snow poles
** http://www.interwestsafety.com/Product/-315/Snow-Poles/
* XX 2x avalanche probes

===Cameras===
* pole?

====To Purchase yet====
* ziplocs
* --> rebar
*

====Itinerary====

====3/20====
* Bob Busey (Noon) & LANL Crew (Evening) arrive in Nome
* Hotel opens @ 3pm
* pick up stuff from cargo
** gear
** safety equipment
* groceries
*

====3/21====
* Lily Cohen & Bob Bolton arrive in Nome
* Hotel opens @ 3pm
** get settled.
** get groceries

====3/22====
Survey marker trip day:
* 8am start
* 10am arrive on-site and set up survey gps system
* 10:45 snowmachine to the top of the drainage. Work down the hill deploying markers
* ~7 hrs to deploy markers for UAV/helo
** Stop sign
** rebar
** wooden anchor
** chains
** paracord
** knife
* evening: return to Nome.
* Snow Poles
*
====3/23====
* Begin snow surveys in Teller
* Proceed from site to site

====Random====
* Radio test in Council?
* Move base station in Nome
* download station data at three loggers in Teller
* End of trip need to deploy Pressure Transducer that is in Nome Storage
* Need to reprogram Teller_SW
* Need to reprogram Teller_top for CFM100

===Stop sign markers===
These markers will be placed on location at the beginning of the trip and will remain through fall 2017 but will require adjusting a couple of times as the snow melts.
==== Parts:====
* rebar
* 1 stop sign
* 4 wooden stakes
* 4 lengths of chain
* 2 grounding nuts
* 4 lengths of paracord
====Tools====
* wrench to tighten grounding nuts
* knife to cut paracord to length
* light hand maul to pound in wooden stakes
* bosch hammer drill
====Instructions for initial deployment====
* Locate site
* push rebar to ground through snowpack.
* place grounding nut on rebar and position 4 - 6 inches above snow surface and tighten
* place stop sign on rebar
* put second grounding nut on rebar making sandwich with stop sign.
* start making deadman anchor by collecting materials
** take one wooden stake
** one rectangle of fencing
** one length of paracord
* string paracord through the middle hole of wooden anchor and also the fencing.
* tie a knot.. could do a larkshead here
* put a chain through one of the four perimeter holes on stop sign.
* run the paracord through the chain and tie a trucker's hitch or similar to keep stop sign taut.
* survey in stop sign using GPS
====Later in first trip====
* when visiting the site on foot, bring the hammer drill.
* excavate a hole down to the ground surface.
* drill a hole with the hammer drill
* put the rebar into this hole
* redo the deadman anchors
* resurvey the stop sign
====Ablation trip====
* adjust deadman as needed
* as the snow decreases it may become useful to transition from deadman anchors in snow to wooden stakes in ground.
* use the hammer drill to predrill a hole at a healthy distance from the stop sign and re-secure the stop sign.