137.229.92.225 at 03:14, 12 April 2011

2011-04-12T03:14:00Z

137.229.92.225 at 22:55, 11 April 2011

2011-04-11T22:55:49Z

New page

Starting with south facing high hillslope site.<br/>

'''Oh, we need to figure out if there is any money left to spend to get up to $5,000 per site. If yes, cable protection should be purchased.'''

To Bring Tools:
* jack hammer & gas (chipping out SM pit)
* Shovels (at least 2) -- snow removal from pit and tripod area
* compass (make sure SP is south-facing)
* hand maul (for pounding in pins & stakes)
* Voltmeter
* tool bag
* cordless drill
** extra battery
** both charged
** screwdriver for a couple of tripod bits
* long drill bit for SM
* short drill bit for 107 probe
* short drill bit for punching holes in the actionpacker for instrumentation
* 7/16" nut driver
* 7/16" wrench
* 5/16" nut driver
* CSI screw driver
* Snow Shoes
* Sled or two
* GPS

To Purchase:
* Another drill bit for SM,
* One for ST

To Bring Site Related:<br/>
* Sap Flow stuff
* Screed stakes (3 pcs) (for precip setup)
* 12" Pins (I can't remember what I called these on the shopping page)
* Hose Clamps
* 12V Battery
* Solar Panel

To Do:<br/>
# Snow shoe gear to site
# Make a snow SWE & Depth measurement?
# Clear ground near SM Pit of snow but be sure not to walk up the hill from the pit.
# Chip out SM Pit, put organic lid on one tarp and the excavated dirt on another. (And snow? Bob and I talked I just can't remember again...)
## Drill 4 holes for SM
## Drill 2 holes for ST
## Label with electrical tape both ends of the SM & ST (install @ 10cm bgs and 40 cm bgs)
### Orange = 10 cmbgs
### Blue = 40 cmbgs
# Do Sap Stuff & label wires
# Put together Tripod
## See tools above.
## Put legs back on the 2x12
## Run cross arm on legs
## Mount SP to cross arm
## Mount anchor point to 2x12 leg.
## Pound 12" pins through anchor points and into the ground
## Hoseclamp AT Pole to cross arm
## Drill holes in clear tote and actionpacker for instrumentation (what is out there plus precip)
## Put battery in box
# Wire sensors to data logger
## See wiring page / program

@@ Line 11: / Line 11: @@
 * Voltmeter
 * tool bag
 * cordless drill
 ** extra battery
@@ Line 23: / Line 24: @@
 * CSI screw driver
 * Snow Shoes
-* Sled or two
+* Sled or three
 * GPS
 To Purchase:
@@ Line 37: / Line 44: @@
 * 12V Battery
 * Solar Panel
 To Do:<br/>
-# Snow shoe gear to site
+# ''Snow shoe'' gear to site via ''sled''
 # Make a snow SWE & Depth measurement?
 # Clear ground near SM Pit of snow but be sure not to walk up the hill from the pit.
@@ Line 45: / Line 59: @@
 ## Drill 4 holes for SM
 ## Drill 2 holes for ST
-## Label with electrical tape both ends of the SM & ST (install @ 10cm bgs and 40 cm bgs)
+## Label with electrical tape both ends of the SM & ST (install @ 5cm bgs and 40 cm bgs)
-### Orange = 10 cmbgs
+### Orange = 5 cmbgs
 ### Blue = 40 cmbgs
 # Do Sap Stuff & label wires
-# Put together Tripod
+# Put together Tripod:
-## See tools above.
+## Put legs back on the 2x12 -> ''7/16 Nut Driver or wrench''
-## Put legs back on the 2x12
+### '''Cone nut / Regular Washer / 1" x 1/4 Bolt''' -> 2x per leg (2 legs)
-## Run cross arm on legs
+## Mount cross arm on legs -> ''7/16 Nut Driver or wrench''
-## Mount SP to cross arm
+### '''Cone nut / Fender Washer / 1" x 1/4 Bolt''' -> 1x per leg (2 legs)
-## Mount anchor point to 2x12 leg.
+## Mount SP to cross arm -> ''7/16 Nut Driver or wrench''
-## Pound 12" pins through anchor points and into the ground
+### '''Cone nut / Fender Washer / 1" x 1/4 Bolt''' -> 1x per leg (2 legs)
-## Hoseclamp AT Pole to cross arm
+## Mount 90degree unistrut angle to 2x12 with ''#2 Phillips & Cordless Drill''
-## Drill holes in clear tote and actionpacker for instrumentation (what is out there plus precip)
+### '''Wood Screw / Fender Washer / Unistrut Angle'''
-## Put battery in box
+## Pound '''12" Galvanized spike''' through '''square washers''' and '''90degree unistrut angles''', then into the ground (2 unistrut legs, 1 2x12) using the hand maul or sledge hammer.
-# Wire sensors to data logger
+## '''Hoseclamp''' AT Pole to cross arm w/ ''5/16" Nut Driver''
-## See wiring page / program
+## Inside Actionpacker work:

BJ CPCRW 4/12 Trip - Revision history

137.229.92.225 at 03:14, 12 April 2011

137.229.92.225 at 22:55, 11 April 2011