Barrow Site D Inventory - Revision history

137.229.92.243 at 00:08, 13 July 2013

2013-07-13T00:08:49Z

137.229.92.213 at 00:02, 13 July 2013

2013-07-13T00:02:55Z

137.229.92.251 at 23:30, 12 July 2013

2013-07-12T23:30:00Z

137.229.92.251 at 23:29, 12 July 2013

2013-07-12T23:29:26Z

New page

* 1 pcs RM Young WS/WD 05103
** S/N 122565
* 2 pcs Vaisala HMP155A
** S/N J0330031
** S/N J0330017
* 1 pcs WS MetOne 014A
** S/N P11970
* 1pcs Kipp & Zonen CNR4 Net Radiometer
** S/N 120971
*** SW Up 12.77
*** SW Dn 14.09
*** LW Up 8.27
*** LW Dn 8.17
* 1pcs Campbell SR50A
** S/N 5085
* 6 pcs East30 Thermal Conductivity Sensors:
** S/N 1483
** S/N 1484
** S/N 1489
** S/N 1500
** S/N 1480
** S/N 1481
* 2 pcs GI Soil Temperature Triple Probe
** S/N TT1208
** S/N TT1205
* 1 pcs GI Shallow Borehole Temperature Profile
** S/N TS1204
* 6 pcs Stevens HydraProbe II Soil Moisture Probe
** ID1 S/N 194738
** ID2 S/N 194745
** ID3 S/N 194739
** ID4 S/N 207302
** ID5 S/N 207303
** ID6 S/N 207317
* 2 pcs Hukseflux HFP01 Heat Flux Plate
** S/N 7873
*** 60.90 uV / (W/m^2)
** S/N 7906
*** 62.59 uV / (W/m^2)
* 1 pcs 107 Probe (I might just drop this)
* 2 pcs Campbell CE4 4-Channel Current Excitation Module
** S/N 1493
** S/N 1494
* 1 pcs Campbell CR1000 data logger
** S/N 55393
* 3 pcs Campbell AM16/32B Multiplexer
** S/N 15112
** S/N 15113
** S/N 15208
* 1 pcs Campbell RF450 Radio
** s/n 9570216

@@ Line 63: / Line 63: @@
 * Correct Pipe for snow stands (any dimensional changes to make?)
 * 4 small antennas for RF450s
+* Cross arm for tower snow
 Tools:
 * 3 inch hole saw
 * 3/4 inch hole saw
 * 5/16" nut driver

← Older revision		Revision as of 00:02, 13 July 2013
Line 51:		Line 51:
	* 1 pcs Campbell RF450 Radio		* 1 pcs Campbell RF450 Radio
	** s/n 9570216		** s/n 9570216
		+
		+	Still Needed:
		+	* Solar Panel
		+	* Solar Panel Mounting aluminum / steel flat stock
		+	* radiation shield for 107 air temperature
		+	* vertical pipe, 3 inch diameter (well, there is one up there at the controls shed I think)
		+	* 3 inch male terminal adapter?
		+	* 4 cross arm brackets
		+	* 1" x 1" nurail for WS/WD sensors at top of tower? Or.... neck the top pipe down to 1 inch and put the anemometer on that.
		+	* Correct NuRail fittings for the snow stands
		+	* Correct Pipe for snow stands (any dimensional changes to make?)
		+	* 4 small antennas for RF450s
		+
		+	Tools:
		+	* 3 inch hole saw
		+	* 3/4 inch hole saw
		+	* 5/16" nut driver

← Older revision		Revision as of 23:30, 12 July 2013
Line 1:		Line 1:
		+	Sensor List (Plus the temperature probes still in Barrow)
	* 1 pcs RM Young WS/WD 05103		* 1 pcs RM Young WS/WD 05103
	** S/N 122565		** S/N 122565