Oliktok summer 2017 trip - Revision history

137.229.92.185: /* for telayna */

2017-09-08T01:14:16Z

for telayna

2017-09-07T23:47:18Z

=other

2017-09-07T22:52:12Z

2017-09-07T21:48:05Z

2017-09-07T21:38:11Z

2017-09-07T19:13:50Z

2017-07-07T19:34:19Z

2017-06-14T19:23:20Z

Created page with "*replace sr50a transducers"

New page

*replace sr50a transducers

@@ Line 10: / Line 10: @@
 **7)screw in all the little screws
 **8)replace the sensor on the mount and screw in the cable (which is notched)
 *put up temperature sensor
-**mount it as close to SR50a quadpod as possible
+**1)mount it on the south side of the fence
 **wiring to CR1000 logger
-**Red     -- SW-12
+***Red     -- SW-12
-**yellow  -- SE11
+***yellow  -- SE11
-**blue    -- SE12
+***blue    -- SE12
-**clear   -- AG
+***clear   -- AG
-**black   -- AG
+***black   -- AG
-**white   -- AG
+***white   -- AG
+**replace putty
 *CFM100
@@ Line 30: / Line 36: @@
 *level geonor
 **there are screws at the base
 **don't do this if it doesn't seem obvious
 *tools i'm sending you with
@@ Line 36: / Line 46: @@
 **small flathead screw driver
 **small Philips screw driver
-**level
+**adjustable wrench
 ===other===

@@ Line 38: / Line 38: @@
 **level
-====other===
+===other===
 *antifreeze
-*snip vegetation underneath
+*<s>snip vegetation underneath
 **cable housing
-*plastic cable covers for all cables entering into the logger?
+*plastic cable covers for all cables entering into the logger?</s>

@@ Line 26: / Line 26: @@
 **2)plug and screw in the CFM100
 **3)re-plug power to the logger
-**4)
+**4)insert card
 *level geonor

@@ Line 21: / Line 21: @@
 **white   -- AG
 *CFM100
@@ Line 29: / Line 27: @@
 **3)re-plug power to the logger
 **4)
 *level geonor
 *tools i'm sending you with
@@ Line 35: / Line 36: @@
 **small flathead screw driver
 **small Philips screw driver
 ====other===
 *antifreeze
 *snip vegetation underneath

@@ Line 1: / Line 1: @@
 *replace sr50a transducers
 **1)unscrew sensor from mount
@@ Line 10: / Line 11: @@
 **8)replace the sensor on the mount and screw in the cable (which is notched)
 *put up temperature sensor
 **cable housing
 *plastic cable covers for all cables entering into the logger?
-*level geonor
 *CFM100
 **1)unplug power from logger
@@ Line 21: / Line 29: @@
 **3)re-plug power to the logger
 **4)

← Older revision		Revision as of 19:34, 7 July 2017
Line 1:		Line 1:
	*replace sr50a transducers		*replace sr50a transducers
		+	**snip vegetation underneath
		+	*antifreeze
		+	*put up temperature sensor
		+	**cable housing
		+	*plastic cable covers for all cables entering into the logger?
		+	*level geonor