Bob: /* Procedure */

2022-09-21T01:13:20Z

Procedure

Bob: /* Tools */

2022-09-21T01:11:26Z

Tools

Bob: Created page with "==Tools== * Stubby Phillips Screwdriver (#2) * 1/2" Nut Driver * Campbell Scientific Phillips Screwdriver (slender #2) * Small handle Channel lock pliers * 5/16" nut driver ==..."

2022-09-19T20:38:41Z

Created page with "==Tools== * Stubby Phillips Screwdriver (#2) * 1/2" Nut Driver * Campbell Scientific Phillips Screwdriver (slender #2) * Small handle Channel lock pliers * 5/16" nut driver ==..."

New page

==Tools==
* Stubby Phillips Screwdriver (#2)
* 1/2" Nut Driver
* Campbell Scientific Phillips Screwdriver (slender #2)
* Small handle Channel lock pliers
* 5/16" nut driver
==Supplies==
* Anti-Corrosion Goo
** https://www.homedepot.com/p/Noalox-Anti-Oxidant-Compound-4-oz-30-026/202276208
* SR50A Replacement Transducer
** https://www.campbellsci.com/order/p19486

==Procedure==
There are several valid ways to change out the transducer. Sometimes it is easiest to leave the sensor connected to the sensor cable other times it is simpler to disconnect completely.

===Method 1===
* Use the 1/2" nut driver to loosen the bolts on the SR50A mounting bracket slightly.
* Once loose, rotate 90 degrees so that the black and golden transducer is facing horizontal.
* Use the Campbell screw driver to loosen each screw and place it somewhere nearby yet secure.
* Once all screws are removed, the transducer remains connected by a power cord. Gently disconnect and set package aside.
* Open the new transducer. Add the desiccant as you see was done with the old one, in the plastic voids in the black part of the transducer.
* Clip the transducer power into the main sensor body.
* dab a bit of the anti-corrosion goo onto each screw before screwing it back into the main sensor body.
** Leave the first screw loose to make it easier to add the others.
** work opposite side to opposite side like you would if you were tightening a car wheel's lug nuts.
** Once every screw is gooed and screwed gently, tighten them all up.
* next, rotate the sr50A back into operational position and tighten up the ubolts on the mounting bracket using the 1/2" nut driver

===Variations===
* Sometimes it is easier to completely remove the SR50A sensor body from the cross arm before starting this procedure (and then it would be done kneeling on the ground).
* To use this method to start then you might use the 5/16" nut driver to loosen hose clamps securing the cable protection (flexible metal conduit).
* Then, use the small channel locks to loosen the cable from the sensor body.
* Finally, use the 1/2" nut driver to loosen the ubolts completely and slide the sensor off its cross arm.
* At this point you can step into the method above at the small screw removal stage.

← Older revision		Revision as of 01:13, 21 September 2022
Line 35:		Line 35:
	* Finally, use the 1/2" nut driver to loosen the ubolts completely and slide the sensor off its cross arm.		* Finally, use the 1/2" nut driver to loosen the ubolts completely and slide the sensor off its cross arm.
	* At this point you can step into the method above at the small screw removal stage.		* At this point you can step into the method above at the small screw removal stage.
		+
		+	===After Replacement===
		+	* Trim the vegetation from below the sensor about 1m diameter (or more if the sensor is high). Use the pruning shears to clip so that in the ideal case you now have a good surface for the signal to bounce off of but also recognizing that this is the real world and the microtopography often leaves things lumpy.

@@ Line 5: / Line 5: @@
 * Small handle Channel lock pliers
 * 5/16" nut driver
 ==Supplies==
 * Anti-Corrosion Goo

Snow Transducer Replacement - Revision history

Bob: /* Procedure */

Bob: /* Tools */

Bob: Created page with "==Tools== * Stubby Phillips Screwdriver (#2) * 1/2" Nut Driver * Campbell Scientific Phillips Screwdriver (slender #2) * Small handle Channel lock pliers * 5/16" nut driver ==..."