Teller Upper Station - Revision history

137.229.92.213 at 19:19, 6 October 2016

2016-10-06T19:19:05Z

66.58.163.81: Replaced content with "'''Tape Color is Yellow''' ===Remaining To Do for fall=== * Bring out a charge controller for solar panel * soil samples from soil pit * soil pit sensors are in a large ac..."

2016-08-19T23:44:50Z

Replaced content with "'''Tape Color is Yellow''' ===Remaining To Do for fall=== * Bring out a charge controller for solar panel * soil samples from soil pit * soil pit sensors are in a large ac..."

137.229.92.185: /* Sensors */

2016-08-05T23:20:47Z

Sensors

66.230.110.177: Created page with "'''Tape Color is Yellow''' ===Inventory=== * Use Aluminum tripod from Museum * Need to replace some bolts... take care of this 8/3 (Aisle was closed at Home Depot) ** See clip..."

2016-08-03T07:31:11Z

Created page with "'''Tape Color is Yellow''' ===Inventory=== * Use Aluminum tripod from Museum * Need to replace some bolts... take care of this 8/3 (Aisle was closed at Home Depot) ** See clip..."

New page

'''Tape Color is Yellow'''
===Inventory===
* Use Aluminum tripod from Museum
* Need to replace some bolts... take care of this 8/3 (Aisle was closed at Home Depot)
** See clipboard for info
* Reuse the 10' x 1" pipe up top used the by the cameras for the net radiometer cross arm
** I think we'll need to have a vertical support partway out the pole to keep it all level.
** could use unistrut for all of this but will need to drill a hole in one of the unistruts because the holes don't entirely line up.
** ubolt horizontal unistrut to tower
** ubolt 1" pipe to horizontal unistrut
** partway out horizontal pipe then add a vertical piece of unistrut.
**
* Two batteries up top. We'll need to helicopter these up.
* battery box for up top remains in 106 to carry sensors out in second shipment.
* Cross arms:
** Net radiometer
** additional one for AT/RH
** Need to figure out what to do up top for the anemometer...
*** 3/4"insert is up there but need to go 3/4" to 1" vertical...
* '''Complications'''
** crossarm ubolts from Campbell aren't big enough diameter to go around this pipe.
**
====Anchoring system====
*
===Sensors===
* 1 Soil pit
** Hydraprobes @ 5 depths
** soil thermal conductivity at 4 depths
** one additional surface temperature
* 1 GIPL VATP (I'm on the fence about the length for this one)
* Met
** HMP155 AT/RH @ 1.5m ''(already up top)''
*** Radiation shield too
** RM Young anemometer for up top
** If have enough, a skin temperature sensor (SI-111)
** CNR4 Net Radiometer ''(already up top)''
** TE525MM with cable
* Anything else?

===Extras===
* Need to measure resistance of heaters for all thermal conductivity sensors
* need to color code all subsurface sensors
* need to make sure extension cords are included for solar panel to charge controller
* same for battery to charge controller
* and again logger to charge controller
* also need fused power and spare fuses
* power jumper cables to put the two batteries in parallel
* Need to drill out hole in battery box for the liquid-tite.
* need to trim back the Vitel cable so that we can wire them up properly
* need to include terminal strips for power, ground, and control of Vitels.
* probably need to figure out if we need additional terminal strips for the thermal conductivity.

===To Buy up top:===
* 1" unistrut pipe clamp for net radiometer
** may have this in our unistrut stock.
* Anchoring system supplies
* review photos for nome storage stock.

@@ Line 1: / Line 1: @@
-'''Tape Color is Yellow'''
+===Sensor Heights===
-===Remaining To Do for fall===
+====Meteorological====
-* Bring out a charge controller for solar panel
+* Air Temperature / Relative Humidity / Dew Point Temperature
-* soil samples from soil pit
+** Vaisala HMP155
-* soil pit sensors are in a large actionpacker next to tower.
+** 2.20 meters above ground surface

@@ Line 35: / Line 35: @@
 ** If have enough, a skin temperature sensor (SI-111)
 ** CNR4 Net Radiometer ''(already up top)''
-** TE525MM with cable
+** TE525MM with cable.
 * Anything else?