Difference between revisions of "Kougraok M64"
Jump to navigation
Jump to search
| Line 60: | Line 60: | ||
|1.5meters | |1.5meters | ||
|? | |? | ||
| − | | | + | |4 in UAF storage, one in box |
|na | |na | ||
|na | |na | ||
| Line 158: | Line 158: | ||
|In Nome Storage | |In Nome Storage | ||
| | | | ||
| − | | | + | |attached |
| − | | | + | |bob says yes! |
| | | | ||
| | | | ||
Revision as of 13:55, 8 June 2017
Tape Color is Green
Contents
- 1 In NGEE Container:
- 2 In UAF Storage
- 3 Sensors in UAF storage
- 4 To Buy in Nome
- 5 To buy in Fairbanks
- 6 Cross arm situation
- 7 To ship from Fairbanks
- 8 Sensors
- 9 infrastructure
- 10 Actionpacker in uaf storage
- 11 General actionpacker placed into storage but may be useful for K64
- 12 Checklist for bob to find in Nome
In NGEE Container:
- Tripod base with green tape. This is in NGEE Container
- Requires 1.25" schedule 40 pipe mast
In UAF Storage
- 1" x 3' aluminum pipe, three pieces
- 2 pipe wrenches
- large cable ties
- small cable ties
- fish tape
- 4 dog anchors
- saw
- grease
- anti oxidizing grease for electrical connections
- a bunch of hose clamps (including for precip bucket
- Bosch drill
- GIPL drill bit
Sensors in UAF storage
- Tipping bucket
- GIPL VATP
To Buy in Nome
- At Grizzly Hardware pick up a 1.25" schedule 40 pipe threaded on two sides
To buy in Fairbanks
- 1" topper for tripod past -Lily asks what is this? (These two items connect RM Young anemometer to the top of the tower)
- 1" to 1.25" coupler to replace one used at teller top site -Lily asks if we still need this?
Cross arm situation
- Use short 1" Aluminum pipe for precip stand at site. Have three of these in the UAF Nome storage as well as the brackets required.
- the hose clamps for the site are in Nome along with some other items.
- Bob found 4 pcs 1" cross arms on 5/30 trip. There were also some 3/4" aluminum cross arms, perhaps for precip stand.
- 1 full altershield in Nome storage but... has flange plates on bottom so we'll need to do a bit more work to get things proper.
To ship from Fairbanks
- 2 pcs 12V batteries
Sensors
| instrument | SN | where? | height | cable | mount | crossarm | crossarm mount |
| HMP155A | 7pcs in UAF Storage | 1.5meters | ? | 4 in UAF storage, one in box | na | na | |
| RMyoung | 1 pcs in UAF Storage | 3meters | ? | in box | in box | Frontier supply stocks them | |
| Barometric pressure | ? | na | ? | na | na | na | |
| CNR4 | in box | in box | in box | ||||
| 3 NDVI sensors | in box | color coded, see SRS notes | attached | in box | |||
| 3 PRI sensors | in box | color coded, see SRS notes | attached | in box | |||
| Skin Temp | in box | attached | in box | ||||
| 5 soil moisture | in box | color coded, see hydraprobe notes | attached | na | na | na | |
| 4 thermal conductivity | only one in box | ||||||
| VAPT | UAF Storage | na | na | na | na | na | |
| SR50a? | UAF Storage... I may have stolen the transducer though... | need longer cable for far one | |||||
| tipping bucket | In Nome Storage | attached | bob says yes! |
Hydra Probe notes
- ID 0 = 5cm = red
- ID 1 = 10cm = orange
- ID 2 = 20cm = purple
- ID 3 = 30cm = brown
- ID 4 = 40cm = black
SRS notes
- PRI up = red tape = 7 SDI address
- PRI #1 = orange = 8 SDI address
- PRI #2 = purple = 9 SDI address
- NDVI up = red tape = A SDI address
- NDVI #1 = orange = B SDI address
- NDVI #2 = purple = C SDI address
Measure resistor value and SN beforehand?
infrastructure
- tower
- tripod - in storage
- mast- called Grizzly 907 443 2108 to see if we can reserve one
- alter shield for tipping bucket?
- power
- solar panel
- wires for panel
- charge controller
- crips/connectors for charge controller wires
- 2 big batteries
- connector wires for batteries
- wire to logger
- fuse
- Enclosure
- mount for enclosure
- logger
- mux
- wires between mux and logger
- cable
- printed program
- screw driver
- CFM100+card
- grounding wire
Actionpacker in uaf storage
- Cable Ties
- 2 pipe wrenches
- hose clmaps
- three camping dinners (seafood deals)
- a bit more snacks
- fish tape
- soil samplers for teller bottom
- duct seal
- grease & anticorrosion goo
- (2) switched 12 volt control
- saw for dirt
- dog anchor
- box screw driver & serial cable (2)
- drill charger
- test radio for kougarok conenctions
- need a cigarette adapter
- hobo kit
- SR50A for K2 & K3
- 1" x 1" ubolt cross arm bracket
- 1" x 1.5" ubolt cross arm bracket
- 1" x 1" nurail cross
- 1" x 3/4" nurail cross
- LANL cameras
- bubble wrap
General actionpacker placed into storage but may be useful for K64
- Misc ubolts
- misc unistrut clamps (mostly wrong sizes I suspect)
- four pieces of unistrut 12-18 inches. two half size two full size
- three things of electrical tape, duct tape, rubber splicing tape
- couple NRS straps 9 & 12 feet
- 1 8GB CF card
- misc wire
- misc other
- baking soda
Checklist for bob to find in Nome
- Tripod kit -- Tripod is in NGEE conex
- trail mat for underneath tripod -- I'm not sure if we have any left
- Batteries for new K64 met tower -- The batteries are in room 112 in basement, or at least one, there are a couple others out there.
- tipping bucket
- hose clamps for mounting it
- cable (how long is it?)
- wind sensor
- cable
- 1 SR50a sensor
- cable (how long is it?)
- mounting kit?
- Barometer
- cable
- what kind of screws do I need to mount it in the enclosure?
- VATP -- it is in Nome
- is there a resistor taped to it?
- HMP155
- cable
- sledge hammer
- shovel
- Drill for VATP
- Is Bob Bolton's sleeping bag there?
- if time: buy mast at Grizzly
