Difference between revisions of "Ibmet"
Jump to navigation
Jump to search
imported>Ken |
|||
| (5 intermediate revisions by 3 users not shown) | |||
| Line 5: | Line 5: | ||
=site logs= | =site logs= | ||
| − | == | + | == 04 Sept 2007, Ken I. == |
| + | * rewired new logger box | ||
| + | * moved ant to tower | ||
| + | * pulled old cables, conduit | ||
| + | * left radio set and yagi on old logger at shack, but radio is DEAD | ||
| + | * installed spare DGR: 906-6035 | ||
| + | * tested conn to UK rep | ||
| + | * set to slave/rep mode 4, 9600 baud | ||
| − | * | + | * Problem talking to site so went back to Imn Met (same day) |
| − | * | + | * radio tested conn to UK rep, good |
| − | + | * logger checked through all cables and connectors, no probs | |
| − | |||
| − | |||
| − | |||
| − | * | ||
| − | * | + | == 16 July 2007, Ken I. == |
| − | * | + | * serviced evaporation pan, at 0925 AKST |
| − | * | + | * water level too low for gauge |
| − | * | + | * w/ hook gage set at 1.00, approx. 2.9 cm down to water level from the hook point |
| + | * added 2 jugs, or 14 gal (52 L) | ||
| + | * hook gage read at 2.7258 | ||
| − | * wiring from logger to multiplexer: | + | == 15 June 2007, Ken I., Doug K. == |
| − | ** SE3 -- CLR -- COM H1 | + | * fixed 10m RMYoung wiring, details follow: |
| − | ** SE4 -- BLK -- COM L1 | + | ** reconnected RMYoung wiring at sensor wiring box to nominal: |
| − | ** AG -- BLK -- COM L2 | + | *** WS SIG -- RED -- 6 |
| − | ** E2 -- RED -- COM H2 | + | *** WS REF -- BLK -- 2 |
| − | + | *** WD EX -- BLU -- 5 | |
| − | * connected 10m WS to P1 & G via wiring board terminal blocks, at lower left, left to right, from multiplexer to sensor on tower: | + | *** WD SIG -- GRN -- 4 |
| − | ** empty | + | *** WD REF -- WHT -- 3 |
| − | ** empty | + | *** DRAIN -- CLR -- 1 |
| − | ** mplx 7L2 -- BLK -- WHT to sensor | + | ** used spare piece of 05103-CSI cable at logger-shack end: |
| − | ** mplx 7H1 -- BLK -- GRN | + | *** per program listing with timestamp 07jun07 02:35:43 |
| − | ** mplx 7H2 -- RED -- BLU | + | *** WS is on C7 |
| − | ** CR10X P1 -- RED | + | *** WD on SE3 (which is multiplexer) |
| − | ** CR10X G -- BLK | + | ** wiring from logger to multiplexer: |
| − | + | *** SE3 -- CLR -- COM H1 | |
| − | * spliced sensor-to-4C cable at either end: | + | *** SE4 -- BLK -- COM L1 |
| − | ** WHT -- WHT cable 1 | + | *** AG -- BLK -- COM L2 |
| − | ** GRN -- GRN cable 1 | + | *** E2 -- RED -- COM H2 |
| − | ** BLU -- RED cable 1 | + | ** connected 10m WS to P1 & G via wiring board terminal blocks, at lower left, left to right, from multiplexer to sensor on tower: |
| − | ** RED -- RED cable 2 | + | *** empty |
| − | ** BLK -- BLK cable 2 | + | *** empty |
| + | *** mplx 7L2 -- BLK -- WHT to sensor | ||
| + | *** mplx 7H1 -- BLK -- GRN | ||
| + | *** mplx 7H2 -- RED -- BLU | ||
| + | *** CR10X P1 -- RED | ||
| + | *** CR10X G -- BLK | ||
| + | ** spliced sensor-to-4C cable at either end: | ||
| + | *** WHT -- WHT cable 1 | ||
| + | *** GRN -- GRN cable 1 | ||
| + | *** BLU -- RED cable 1 | ||
| + | *** RED -- RED cable 2 | ||
| + | *** BLK -- BLK cable 2 | ||
Latest revision as of 11:21, 6 June 2008
Contents
site TODO list
- record as-built wiring of soil sensors
- Flex conduit as needed
site logs
04 Sept 2007, Ken I.
- rewired new logger box
- moved ant to tower
- pulled old cables, conduit
- left radio set and yagi on old logger at shack, but radio is DEAD
- installed spare DGR: 906-6035
- tested conn to UK rep
- set to slave/rep mode 4, 9600 baud
- Problem talking to site so went back to Imn Met (same day)
- radio tested conn to UK rep, good
- logger checked through all cables and connectors, no probs
16 July 2007, Ken I.
- serviced evaporation pan, at 0925 AKST
- water level too low for gauge
- w/ hook gage set at 1.00, approx. 2.9 cm down to water level from the hook point
- added 2 jugs, or 14 gal (52 L)
- hook gage read at 2.7258
15 June 2007, Ken I., Doug K.
- fixed 10m RMYoung wiring, details follow:
- reconnected RMYoung wiring at sensor wiring box to nominal:
- WS SIG -- RED -- 6
- WS REF -- BLK -- 2
- WD EX -- BLU -- 5
- WD SIG -- GRN -- 4
- WD REF -- WHT -- 3
- DRAIN -- CLR -- 1
- used spare piece of 05103-CSI cable at logger-shack end:
- per program listing with timestamp 07jun07 02:35:43
- WS is on C7
- WD on SE3 (which is multiplexer)
- wiring from logger to multiplexer:
- SE3 -- CLR -- COM H1
- SE4 -- BLK -- COM L1
- AG -- BLK -- COM L2
- E2 -- RED -- COM H2
- connected 10m WS to P1 & G via wiring board terminal blocks, at lower left, left to right, from multiplexer to sensor on tower:
- empty
- empty
- mplx 7L2 -- BLK -- WHT to sensor
- mplx 7H1 -- BLK -- GRN
- mplx 7H2 -- RED -- BLU
- CR10X P1 -- RED
- CR10X G -- BLK
- spliced sensor-to-4C cable at either end:
- WHT -- WHT cable 1
- GRN -- GRN cable 1
- BLU -- RED cable 1
- RED -- RED cable 2
- BLK -- BLK cable 2
- reconnected RMYoung wiring at sensor wiring box to nominal:
