Difference between revisions of "2015 July Nome Trip"
Jump to navigation
Jump to search
(5 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
===PreTrip To Do=== | ===PreTrip To Do=== | ||
− | |||
− | |||
* load maps onto phone / touch pad | * load maps onto phone / touch pad | ||
* review programs again. | * review programs again. | ||
* CR1000 for K3 site... add full program if time allows | * CR1000 for K3 site... add full program if time allows | ||
− | * | + | * CNR4 Bracket - locate |
+ | |||
===To bring back=== | ===To bring back=== | ||
− | + | * Old thaw probes | |
+ | * Evap Pan? | ||
+ | * | ||
===To Bring=== | ===To Bring=== | ||
− | |||
* Electricians putty | * Electricians putty | ||
* Temperature sensors for repeater sites | * Temperature sensors for repeater sites | ||
* lithium backup battery w/ charger | * lithium backup battery w/ charger | ||
− | |||
* Satphone | * Satphone | ||
* fieldbook | * fieldbook | ||
− | |||
* maps for kigluaiks | * maps for kigluaiks | ||
* toolbags | * toolbags | ||
* volt meter | * volt meter | ||
− | * | + | * 2 pieces 107 probe |
* gopro w/ chest mount | * gopro w/ chest mount | ||
* Chargers | * Chargers | ||
Line 29: | Line 27: | ||
** lithium battery | ** lithium battery | ||
** bluetooth speaker | ** bluetooth speaker | ||
+ | * CR2032 batteries for Kenji's Hobos | ||
+ | * Diode for Anvil Mountain | ||
===To Buy=== | ===To Buy=== | ||
* screw in anchors for radiation towers and 10 meter tripods | * screw in anchors for radiation towers and 10 meter tripods | ||
− | + | * shoe oil | |
===To grab from storage=== | ===To grab from storage=== | ||
* Pepper Spray | * Pepper Spray | ||
− | * hand maul for tower | + | * hand maul for tower?? |
− | * pipe the right size is in there | + | * pipe the right size is in there for the cross arm @ K3 |
+ | ** use the one from C3 plus a bit of unistrut (seen in pictures) | ||
+ | * check for how many radiometer cases there are in the Nome Storage... I think the Kougarok ones remain in the Kougarok conex (pictures are indeterminant). | ||
+ | |||
=== Anvil Mountain=== | === Anvil Mountain=== | ||
* Add 107 Temperature for air temperature | * Add 107 Temperature for air temperature | ||
− | |||
* Look at WS again | * Look at WS again | ||
** bring out a diode. | ** bring out a diode. | ||
− | * | + | * remove HMP45C |
+ | ** bring out a bit more duct seal | ||
+ | |||
+ | ===Monday 7/27:=== | ||
+ | * Fly to Nome | ||
+ | * pick up vehicle | ||
+ | * visit storage | ||
+ | ** pick up water jugs | ||
+ | ** cooler | ||
+ | ** pepper spray | ||
+ | ** Pipe for k3 | ||
+ | ** unistrut for k3 | ||
+ | ** radiometer carryying cases if they are here | ||
+ | *** get water @ hotel | ||
+ | ** get pepper spray (from store or storage depending) | ||
+ | * get a cross arm & extra rod / pipe from nome storage for shrub site radiation | ||
+ | * grocery store | ||
+ | ** yogurt & garbage snacks | ||
+ | ** coke etc | ||
+ | ** ice for cooler | ||
+ | * get set up in Kougarok & download data from the sites over radio network. | ||
+ | |||
+ | ===Tuesday 7/28:=== | ||
+ | * if there is time in the morning, run over to K2 Met and do required things there. | ||
+ | * Take crew from Nome to K3 Mauze | ||
+ | * Add a CR1000 and radiation sensors | ||
+ | * bring cable protection | ||
+ | * and PEP radiometers to site. (brown tape calibration information) | ||
+ | |||
+ | ===Wednesday 7/29:=== | ||
+ | * If K2 is done then try to visit the Kigluaiks Site | ||
+ | * If Kig site is inaccessible then visit Council: C1, Kenji's site, Skookum | ||
+ | * Or, chill with rest of NGEE team | ||
+ | * Return to Nome | ||
+ | |||
+ | ===Thursday 7/30:=== | ||
+ | * Chill with rest of NGEE team | ||
+ | * Spend night in Nome | ||
+ | |||
+ | ===Friday 7/31:=== | ||
+ | * Return to Fairbanks | ||
+ | |||
+ | |||
+ | Potential Stuff to do: | ||
+ | ====K1 Burn==== | ||
+ | * Download data over radio network | ||
+ | |||
+ | ====K2 Met: No Fire Danger==== | ||
+ | * Download data over radio network | ||
+ | * bring out supplies to firm up guy wire anchors for tower and radiation tower | ||
+ | * examine tower to see if it is safe for climbing | ||
+ | * download data | ||
+ | * replace desiccant in radiometers | ||
+ | * remove CR800 | ||
+ | |||
+ | ====K2 Met: Fire Risk but safe for travel==== | ||
+ | * Download data over radio network | ||
+ | * Look in Nome Storage for Eppley Radiometer Cases | ||
+ | ** I think they are actually in the Kougarok conex. | ||
+ | * Remove all hardware it is possible to remove. | ||
+ | |||
+ | |||
+ | ====K3 Mauze Gulch: No Fire Danger==== | ||
+ | * Download data over radio network | ||
+ | * bring out cross arm and additional support for CNR4 | ||
+ | * Try to re-use Q7 Rebs Net Radiometer Bracket with cross Arm | ||
+ | * SI-111 bracket for cross arm | ||
+ | * bring out CR1000 for radiation | ||
+ | * wire to power CR1000 from existing CR10X | ||
+ | |||
+ | ====K3 Mauze Gulch: Fire Risk but safe for travel==== | ||
+ | * Download data over radio network | ||
+ | * pull CR10X & anemometer and other easy to remove items. | ||
* | * | ||
− | ===Skookum=== | + | ====C1 Grid==== |
− | * | + | * Re-level precip bucket |
+ | |||
+ | ====Kenji Bear Creek:==== | ||
+ | * replace hobo and soil surface / well temperature sensors | ||
+ | |||
+ | ====Skookum Pass==== | ||
+ | * Replace CR10X w/ pakbus CR10X | ||
+ | ** program and update firmware in Fairbanks first... test... | ||
+ | * add radiation shield for air temperature sensor | ||
+ | |||
+ | ====Anvil City==== | ||
+ | * look in box to see what Chas left. | ||
+ | ** download program to make sure we have latest | ||
+ | ** change OS to pakbus & resend program | ||
+ | * Visit Kenji's two hobos. | ||
+ | ** download data & change batteries | ||
+ | |||
+ | ====Kigulaiks==== | ||
+ | * Replace CR10X w/ pakbus CR10X | ||
+ | ** bring out hose clamps & tape to secure new AT inside radiation shield | ||
+ | ** maybe use project wire if there is any in storage? | ||
+ | |||
+ | ====Anvil Mountain==== | ||
+ | * Replace CR10X w/ pakbus CR10X | ||
+ | * Bring out diode for wind speed sensor | ||
+ | |||
+ | |||
+ | To Do in Fairbanks: | ||
+ | * grab another anchor or two for radiation stand | ||
− | + | Packing List: | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | + | Trip Extras | |
− | * | + | * hose clamps / tape / for securing 107 temperatures into old radiation shields |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | * | + | Computer Package 1 (Campbell Scientific): |
− | ** | + | * 2 serial cables |
− | * | + | * SC32B |
− | * | + | * Rugged Freewave Radio (unconfigured currently) |
− | * | + | * Waterproof Freewave Radio (unconfigured currently) |
+ | * waterproof freewave cable | ||
+ | * stub antenna | ||
− | * | + | Computer Package 2 (Hobo) |
− | * | + | * small phillips screwdriver (to open hobo) |
− | ** | + | * small flat head screwdriver (to slip out old hobo battery) |
+ | * 2 temperature cables for Bear River Site (Kenji Council Site) | ||
+ | * hobo for bear river site | ||
+ | * USB cable to communicate with Hobo | ||
+ | * extra CR2032 batteries for Anvil City Hobos | ||
− | + | Anvil Mountain Repeater Package: | |
− | * | + | * Anvil CR10X |
− | * | + | * 107 Probe --NOT NECESSARY, 107 INSTALLED IN 2014 |
− | * | + | * small diodes to Wind Speed sensor |
− | * | + | Kigluaiks Repeater Package: |
− | * | + | * Kigluaiks CR10X |
+ | * 107 Probe | ||
− | + | Skookum Repeater Package: | |
− | * | + | * CR10X Logger |
− | + | K2 Met Package: | |
− | * | + | * Desiccant for radiometers |
− | * | + | * 5 pcs - screw in stakes for guy wire anchors |
− | * | + | * guy wire extra cabling? |
+ | * | ||
+ | |||
+ | K3 Mauze Package that is already in Nome: | ||
+ | * SI-111 & Cable & Mount (on PEP) | ||
+ | * | ||
+ | |||
+ | K3 Mauze Package for new radiation stuff: | ||
+ | * CR1000 w/ program | ||
+ | * power cord for CR1000 (run from CR10x) | ||
+ | * cable protection for new sensor cable | ||
+ | * ... I am leaning towards holding off for now, fire danger seems to high. |
Latest revision as of 16:19, 19 October 2015
Contents
PreTrip To Do
- load maps onto phone / touch pad
- review programs again.
- CR1000 for K3 site... add full program if time allows
- CNR4 Bracket - locate
To bring back
- Old thaw probes
- Evap Pan?
To Bring
- Electricians putty
- Temperature sensors for repeater sites
- lithium backup battery w/ charger
- Satphone
- fieldbook
- maps for kigluaiks
- toolbags
- volt meter
- 2 pieces 107 probe
- gopro w/ chest mount
- Chargers
- USB for Gopro / delorme
- phone
- lithium battery
- bluetooth speaker
- CR2032 batteries for Kenji's Hobos
- Diode for Anvil Mountain
To Buy
- screw in anchors for radiation towers and 10 meter tripods
- shoe oil
To grab from storage
- Pepper Spray
- hand maul for tower??
- pipe the right size is in there for the cross arm @ K3
- use the one from C3 plus a bit of unistrut (seen in pictures)
- check for how many radiometer cases there are in the Nome Storage... I think the Kougarok ones remain in the Kougarok conex (pictures are indeterminant).
Anvil Mountain
- Add 107 Temperature for air temperature
- Look at WS again
- bring out a diode.
- remove HMP45C
- bring out a bit more duct seal
Monday 7/27:
- Fly to Nome
- pick up vehicle
- visit storage
- pick up water jugs
- cooler
- pepper spray
- Pipe for k3
- unistrut for k3
- radiometer carryying cases if they are here
- get water @ hotel
- get pepper spray (from store or storage depending)
- get a cross arm & extra rod / pipe from nome storage for shrub site radiation
- grocery store
- yogurt & garbage snacks
- coke etc
- ice for cooler
- get set up in Kougarok & download data from the sites over radio network.
Tuesday 7/28:
- if there is time in the morning, run over to K2 Met and do required things there.
- Take crew from Nome to K3 Mauze
- Add a CR1000 and radiation sensors
- bring cable protection
- and PEP radiometers to site. (brown tape calibration information)
Wednesday 7/29:
- If K2 is done then try to visit the Kigluaiks Site
- If Kig site is inaccessible then visit Council: C1, Kenji's site, Skookum
- Or, chill with rest of NGEE team
- Return to Nome
Thursday 7/30:
- Chill with rest of NGEE team
- Spend night in Nome
Friday 7/31:
- Return to Fairbanks
Potential Stuff to do:
K1 Burn
- Download data over radio network
K2 Met: No Fire Danger
- Download data over radio network
- bring out supplies to firm up guy wire anchors for tower and radiation tower
- examine tower to see if it is safe for climbing
- download data
- replace desiccant in radiometers
- remove CR800
K2 Met: Fire Risk but safe for travel
- Download data over radio network
- Look in Nome Storage for Eppley Radiometer Cases
- I think they are actually in the Kougarok conex.
- Remove all hardware it is possible to remove.
K3 Mauze Gulch: No Fire Danger
- Download data over radio network
- bring out cross arm and additional support for CNR4
- Try to re-use Q7 Rebs Net Radiometer Bracket with cross Arm
- SI-111 bracket for cross arm
- bring out CR1000 for radiation
- wire to power CR1000 from existing CR10X
K3 Mauze Gulch: Fire Risk but safe for travel
- Download data over radio network
- pull CR10X & anemometer and other easy to remove items.
C1 Grid
- Re-level precip bucket
Kenji Bear Creek:
- replace hobo and soil surface / well temperature sensors
Skookum Pass
- Replace CR10X w/ pakbus CR10X
- program and update firmware in Fairbanks first... test...
- add radiation shield for air temperature sensor
Anvil City
- look in box to see what Chas left.
- download program to make sure we have latest
- change OS to pakbus & resend program
- Visit Kenji's two hobos.
- download data & change batteries
Kigulaiks
- Replace CR10X w/ pakbus CR10X
- bring out hose clamps & tape to secure new AT inside radiation shield
- maybe use project wire if there is any in storage?
Anvil Mountain
- Replace CR10X w/ pakbus CR10X
- Bring out diode for wind speed sensor
To Do in Fairbanks:
- grab another anchor or two for radiation stand
Packing List:
Trip Extras
- hose clamps / tape / for securing 107 temperatures into old radiation shields
Computer Package 1 (Campbell Scientific):
- 2 serial cables
- SC32B
- Rugged Freewave Radio (unconfigured currently)
- Waterproof Freewave Radio (unconfigured currently)
- waterproof freewave cable
- stub antenna
Computer Package 2 (Hobo)
- small phillips screwdriver (to open hobo)
- small flat head screwdriver (to slip out old hobo battery)
- 2 temperature cables for Bear River Site (Kenji Council Site)
- hobo for bear river site
- USB cable to communicate with Hobo
- extra CR2032 batteries for Anvil City Hobos
Anvil Mountain Repeater Package:
- Anvil CR10X
- 107 Probe --NOT NECESSARY, 107 INSTALLED IN 2014
- small diodes to Wind Speed sensor
Kigluaiks Repeater Package:
- Kigluaiks CR10X
- 107 Probe
Skookum Repeater Package:
- CR10X Logger
K2 Met Package:
- Desiccant for radiometers
- 5 pcs - screw in stakes for guy wire anchors
- guy wire extra cabling?
K3 Mauze Package that is already in Nome:
- SI-111 & Cable & Mount (on PEP)
K3 Mauze Package for new radiation stuff:
- CR1000 w/ program
- power cord for CR1000 (run from CR10x)
- cable protection for new sensor cable
- ... I am leaning towards holding off for now, fire danger seems to high.