Difference between revisions of "Summer 2016 visit"
Jump to navigation
Jump to search
(3 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
+ | ===Todo list=== | ||
*get tower safety trained | *get tower safety trained | ||
*CANOE out to figure all of underwater sensors out! | *CANOE out to figure all of underwater sensors out! | ||
Line 17: | Line 18: | ||
*BRING PLUVIO USB CABLE | *BRING PLUVIO USB CABLE | ||
*ANTIFREEZE for pluvio | *ANTIFREEZE for pluvio | ||
+ | *level radiometers, tipping bucket | ||
+ | *write plan for cleaning underwater PAR and checking evap pan | ||
+ | |||
+ | ===accomplished=== | ||
+ | 8/23/16 | ||
+ | * emptied pluvio | ||
+ | * ran guided accuracy test on Pluvio => now working! | ||
+ | * lake trip | ||
+ | **swapped lake par sensor. it is anchored to the bottom 130cm below lake surface that day (attached to the white buoy) | ||
+ | **pulled up 107 and added it to this anchor | ||
+ | **pulled up pressure transducer, threw it back out REMEMBER TO null out data!!! | ||
+ | |||
+ | 8/26/16 | ||
+ | *broke down old TPS tripod (took photos) | ||
+ | *took out old base station radio, NL100 and kitchen timer | ||
+ | *added antifreeze mixed with water to the pluvio | ||
+ | *checked level on tipping bucket- still level | ||
+ | *leveled total solar radiation | ||
+ | *leveled UVB + CNR4 (UVA already leveled) | ||
+ | *replaced snow transducer | ||
+ | *installed new mesh panel on outer pluvio fence | ||
+ | *put 107 back on pressure transducer anchor | ||
+ | ** attached orange buoy | ||
+ | ** it was 2m deep on that day, though anchored to bottom |
Latest revision as of 12:56, 29 August 2016
Todo list
- get tower safety trained
- CANOE out to figure all of underwater sensors out!
- lake depth, lake par, lake temp
- measuring tape
- inspect pressure transducer and change desiccant
- figure out what is measuring temperature
- swap underwater quantum
- replace snow transducer
- remove old radio antenna
- bring longer conduit housing for evap pan
- mesh for pluvio
- bring wood, nails, hammer
- guided accuracy test pluvio
- take down TPS tripod
- take out base station for old radio? ask jim first- he said ok
- fix snow depth output/program, right now snow_depth_1 and temp_corr are basically the same and not usefully different
- BRING PLUVIO USB CABLE
- ANTIFREEZE for pluvio
- level radiometers, tipping bucket
- write plan for cleaning underwater PAR and checking evap pan
accomplished
8/23/16
- emptied pluvio
- ran guided accuracy test on Pluvio => now working!
- lake trip
- swapped lake par sensor. it is anchored to the bottom 130cm below lake surface that day (attached to the white buoy)
- pulled up 107 and added it to this anchor
- pulled up pressure transducer, threw it back out REMEMBER TO null out data!!!
8/26/16
- broke down old TPS tripod (took photos)
- took out old base station radio, NL100 and kitchen timer
- added antifreeze mixed with water to the pluvio
- checked level on tipping bucket- still level
- leveled total solar radiation
- leveled UVB + CNR4 (UVA already leveled)
- replaced snow transducer
- installed new mesh panel on outer pluvio fence
- put 107 back on pressure transducer anchor
- attached orange buoy
- it was 2m deep on that day, though anchored to bottom