Difference between revisions of "2022 NGEE Utqiagvik September Trip"

From IARC 207 Wiki
Jump to navigation Jump to search
(Created page with "==Activities== ==To Bring== * Radiometer Desiccant * SR50A transducers * Anemometers * Tap & Die set for radiometers * Anti Corrosion Goo * Toughbook * Toolbags * Computer =...")
 
 
(3 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
==Trip Notes==
 +
Anti corrosion goo saved the day here.  No screws stripped on this visit.  Everything easy to swap.  Definite best case scenario after a three year gap between visits.
 +
* @ Site A
 +
** Replaced all  AT/RH and 014A sensors with new / recalibrated units
 +
*** Lower 014A had bent cups but both should be reading NAN until visit.
 +
** replaced both snow transducers
 +
** leveled CNR4 and replaced desiccant
 +
** leveled tipping bucket
 +
** site back to 100%.
 +
* @ Site B
 +
** Replaced all  AT/RH and 014A sensors with new / recalibrated units
 +
** replaced both snow transducers
 +
*** Tripod SR50A not reading.  I looked over the wires and the data and I think this must have been an issue in 2019, too as all the wiring looks ok.  So I vote internal corrosion or something else.
 +
** leveled CNR4 and replaced desiccant
 +
* @ Site C
 +
** Replaced both 014A WS
 +
** Only replaced upper HMP155.  The lower one is still working and and the sensor cable was corroded onto the sensor.  I think with a skinny wrench (and here I am thinking probably a metric bike tool would be the hot ticket) they could be disconnected but since it was still working, shoulder shrug emoji, just left it as-is.
 +
** Tipping bucket still level and so didn't fuss with it.
 +
* @ Site D
 +
** Replaced the 014A WS
 +
** Did not replace HMP155 as it is still working.
 +
* @ BEO Control Shed
 +
** Redeployed the computer
 +
** it worked right off and data downloads resumed.
 +
** now using an internal IP address and pushing data to ocotal
 +
** SSH connection to monitors is broken by monitors firewall so I will need to look into current IP.
 +
 
==Activities==
 
==Activities==
 +
* I listed things working and broken below but I also brought enough instruments to completely replace:
 +
** All [[Snow Transducer Replacement|snow transducers]]
 +
 +
** All [[HMP155 Sensor Replacement|AT/RH]]
 +
** All [[MetOne 014A Anemometer Replacement |WS]]
 +
** All [[CNR4 Desiccant Replacement |CNR4 desiccant]]
  
 
==To Bring==
 
==To Bring==
Line 11: Line 44:
 
* Computer
 
* Computer
  
−
==To Ship==
+
==Data Refresher==
 +
===These notes as of May 2021 download....===
 +
* Site A Notes suggest nothing major wrong
 +
** 3.5m at/rh might be in need of replacement
 +
** planning to replace both ws
 +
** replace desiccant in CNR4
 +
** Level tipping bucket
 +
* Site B Notes
 +
** Replace lower AT/RH
 +
** replace both WS
 +
** replace desiccant in CNR4
 +
** Level tipping bucket (could ignore since I don't really use this one after a data review)
 +
* Site C Notes
 +
** 3.5m at/rh might be in need of replacement
 +
** planning to replace both ws
 +
** replace desiccant in CNR4
 +
** Level tipping bucket
 +
* Site D Notes
 +
** planning to replace ws
 +
** replace desiccant in CNR4

Latest revision as of 10:03, 23 September 2022

Trip Notes

Anti corrosion goo saved the day here. No screws stripped on this visit. Everything easy to swap. Definite best case scenario after a three year gap between visits.

  • @ Site A
    • Replaced all AT/RH and 014A sensors with new / recalibrated units
      • Lower 014A had bent cups but both should be reading NAN until visit.
    • replaced both snow transducers
    • leveled CNR4 and replaced desiccant
    • leveled tipping bucket
    • site back to 100%.
  • @ Site B
    • Replaced all AT/RH and 014A sensors with new / recalibrated units
    • replaced both snow transducers
      • Tripod SR50A not reading. I looked over the wires and the data and I think this must have been an issue in 2019, too as all the wiring looks ok. So I vote internal corrosion or something else.
    • leveled CNR4 and replaced desiccant
  • @ Site C
    • Replaced both 014A WS
    • Only replaced upper HMP155. The lower one is still working and and the sensor cable was corroded onto the sensor. I think with a skinny wrench (and here I am thinking probably a metric bike tool would be the hot ticket) they could be disconnected but since it was still working, shoulder shrug emoji, just left it as-is.
    • Tipping bucket still level and so didn't fuss with it.
  • @ Site D
    • Replaced the 014A WS
    • Did not replace HMP155 as it is still working.
  • @ BEO Control Shed
    • Redeployed the computer
    • it worked right off and data downloads resumed.
    • now using an internal IP address and pushing data to ocotal
    • SSH connection to monitors is broken by monitors firewall so I will need to look into current IP.

Activities

  • I listed things working and broken below but I also brought enough instruments to completely replace:

To Bring

  • Radiometer Desiccant
  • SR50A transducers
  • Anemometers
  • Tap & Die set for radiometers
  • Anti Corrosion Goo
  • Toughbook
  • Toolbags
  • Computer

Data Refresher

These notes as of May 2021 download....

  • Site A Notes suggest nothing major wrong
    • 3.5m at/rh might be in need of replacement
    • planning to replace both ws
    • replace desiccant in CNR4
    • Level tipping bucket
  • Site B Notes
    • Replace lower AT/RH
    • replace both WS
    • replace desiccant in CNR4
    • Level tipping bucket (could ignore since I don't really use this one after a data review)
  • Site C Notes
    • 3.5m at/rh might be in need of replacement
    • planning to replace both ws
    • replace desiccant in CNR4
    • Level tipping bucket
  • Site D Notes
    • planning to replace ws
    • replace desiccant in CNR4
Retrieved from "http://ocotal.iarc.uaf.edu/index.php?title=2022_NGEE_Utqiagvik_September_Trip&oldid=4289"