Difference between revisions of "Teller Lower Station"
Jump to navigation
Jump to search
Line 5: | Line 5: | ||
===Outstanding Items=== | ===Outstanding Items=== | ||
* Make Discharge Measurement | * Make Discharge Measurement | ||
+ | ** Tools: | ||
+ | ** Cloth Tape | ||
* Need to bring out | * Need to bring out | ||
* 1" Al pipe for away from tripod snow stand... can skinny pipe be made to work? | * 1" Al pipe for away from tripod snow stand... can skinny pipe be made to work? | ||
− | * Declination is 11 degrees... | + | ** Tools: 1/2" nut driver / wrench |
+ | * Declination is 11 degrees... correct this later using datapro function. | ||
* XX use battery box tarp to flop soil pit lid onto. | * XX use battery box tarp to flop soil pit lid onto. | ||
+ | ** tape measure | ||
+ | ** saw | ||
+ | ** tarp | ||
+ | ** shovel | ||
* camera power | * camera power | ||
* XX terminal strips for SDI 12 devices. | * XX terminal strips for SDI 12 devices. | ||
Line 15: | Line 22: | ||
* mount camera | * mount camera | ||
* fix program problems: | * fix program problems: | ||
− | ** | + | ** Resistance logging |
** soil temperature logging | ** soil temperature logging | ||
** check to see that east 30 sensors are good with the jumper wire in place | ** check to see that east 30 sensors are good with the jumper wire in place |
Revision as of 10:03, 14 August 2016
Tape Color is BLUE
Contents
To Bring:
Outstanding Items
- Make Discharge Measurement
- Tools:
- Cloth Tape
- Need to bring out
- 1" Al pipe for away from tripod snow stand... can skinny pipe be made to work?
- Tools: 1/2" nut driver / wrench
- Declination is 11 degrees... correct this later using datapro function.
- XX use battery box tarp to flop soil pit lid onto.
- tape measure
- saw
- tarp
- shovel
- camera power
- XX terminal strips for SDI 12 devices.
- XX 1"x1ft stub for net radiation
- XX guy wires for snow stand
- mount camera
- fix program problems:
- Resistance logging
- soil temperature logging
- check to see that east 30 sensors are good with the jumper wire in place
Cross Arms
- Net Radiometer skin temperature
- need to track down unistrut & strut clamps for stabilization (or ubolts)
- small cross arm for air temperature
- RM Young should mount to top without issue.
- Precip stand is already out there
- Need to figure out where NDVI sensors point. & do we have all supplies for that...
Sensors
To Bring:
- 015103 WS/WD
- Make up cable for it
- CR200 for measuring Pressure Transducers
- 5 pcs VITEL Hydraprobe II
- 4 pcs East30 sensors thermal conductivity or specific heat
- also interface board
- also measure the heater resistance of each
- Cable protection
- cable ties & hose clamps for securing cabling to tripod
- VATP 1504 - see email for thermistor calibration offsets
Sensor Heights
- Anemometer @ top of tripod / ~3 meters
- HMP155 @ 1.5m above ground surface
- Barometric Pressure - in instrument box
- Net Radiation -
- Snow Temperature profile -- ground surface in the shrubs
- Snow Depth 1 -- 2m on cross arm off station
- Snow Depth 2 -- in shrubs on a stand.
Already at site:
- HMP155
- thinking about bringing out a replacement temperature head though because the one in place has been on the fritz over the summer.
- TE525MM
- CNR4 w/bracket
- Two Batteries
- Solar Panel
- Charge Controller
Extras
- think about how to mount iridium here...
- Bring covers from Fairbanks to cover unitstrut ends like tennis balls.