2022 NGEE Nome May Trip

Purpose:

Spring station data download and creek measurement.

Trip Summary and Loose Ends

• Teller Bottom Soil Moisture sensor need a bit of attention. No SDI 12 action.
• Buy and bring out a short step ladder for Teller Bottom CNR4
• Teller IS2 charge controller doesn't look to be working (confirmed looking at March data download).

Teller bottom 2022-05-20

• Problem files
  • Micromet110.dat
  • Mm112
• Anemometer:
  • With yellow boat compass east /west line is at 294 magnetic. From east looking west at anemometer box

Teller SW

• Teller creek is probably highest observed discharge
• Teller sw could use one serial cable

Teller IS2 Snow

• Need a base plate for 4x4 to keep it from sinking further into muck. That turns out to be the source/reason for the lean.
• Limited Lean 5/22/22 by pounding in rebar with guy wire anchor. Could use rebar cap from storage for it (or from Fairbanks)
• Also on 5/22/22: Verified voltage of solar panel and battery. Charge controller needs replacement

Kougarok m64

• Looking east to west anemometer box is at 273 degrees magnetic
• Snipped the pressure vent tube but thinking I should return with something more. Like pvc pipe going to ground so there is even less chance of clogging. Like could add the T sections of drill holes in pipe for venting

Kg is5 snow

• Battery box lid blew away. Otherwise good
• Could use a sticky hook to hold serial cables up inside these boxes

KG South Transect Snow

• All good here nothing to change.

Teller 47

• Guy wire off again creek side
• Anemometers
  • Lower anemometer at 275 magnetic pointing east to west
  • Upper at 270 magnetic pointing east to west
• Baud rate on md485 set to 9600. I always forget so might need to adjust serial port speed before collecting here
  • Should really buy a couple of the rs232 cables for the cr6 cas sites
• Screwed up program change last fall and recorded extreme high resolution snow depth here. Fixed that. Downloaded data from microSD card.
• Should look at pressure data here and compare to teller bottom.
• There are flies in the vent and it should be replaced
• Three battery setup lasted all winter.
• Not much water in bucket but still dumped.
• I think we have a baby oil in conex for fall 2022 geonor.

Teller 47 Snow

• Vertical pipe bent a bit over the winter.

Teller Top

• Was going to disconnect and reconnect wiring for HMP155 to see if the weak connection is not the sensor.
  • might also try leaving sensor turned on for longer in program (a to do for when CNR4 returns recalibrated)
  • Musk Ox within 50 meters of station prevented a visit.

Snow Stand Improvements

• Shipped out in March parts to add a snow depth side diagonal support (just need to buy the pipe).
  • Teller 47 snow
  • KG-IS5 snow
  • Teller IS2 2x
• Should also add back side guy wires to:
  • Teller IS2 2x
  • Teller 47 snow
  • KG-IS5 Snow 2x

Safety Docs Submitted to Risk Management

• 4/28/2022
• Approved: 5/11/2022

Proposed Itinerary

Day 1 --- May 20 2022

• Fly in around Noon.
• Pick up Truck.
• Drive to Teller 27
  • Gage the Creek
  • Download data from all sites at bottom
  • Replace radiometer at Teller Bottom
  • Fix anything broken
    • We won't fix the mast at IS2 snow site but might take it down?
      • Consider bringing a saw to cut it.
      • Look at snow depths and pictures and then put a shorter mast in its place come fall?
• 1:30 PM -- on the road for Teller 27
• 2:30 PM -- arrive
• 3:00 PM -- arrive at the bottom.
• 6:00 PM -- Finish for the day
• 7:00 PM -- Arrive back in Nome

Day 2 --- May 21 2022

• If road passable, drive to mile 64 site
• Hike to sites and download data (expecting there to be snow some places)
• (In March everything was working out here.)
• Drive to end of road and download older sites via radio.
• Replace pressure sensor at met station
• Photos of anemometer
• replace desiccant in CNR4 and relevel

Day 3 --- May 22 2022

• Drive to Teller 47 site
  • download data
  • dump precip bucket
    • need baby oil
  • level radiometer
  • check anemometer for true north
  • (ordered a replacement SR50A for the willows site. Will need to deploy in 2022)
• Drive to teller top
  • download data
  • HMP155 cable, try redoing the connections inside the instrument box.
• If time, measure discharge again.

Day 4 --- May 23 2022

• Wrap up loose ends in town
• Return home on morning flight