2016 NGEE August Nome Trip

Second Trip:

August 11 - 19

pre trip

• find large wrenches to bring for drill bits
• wire rope cable cutters

To Purchase

• 5 more dog anchors
• 2.5" unistrut clamps (for solar panel teller top)
• crimping tool
• white duct tape
• I think we under counted on SR50A cables / cross arm brackets.

Second Trip To Do List:

• @ Teller
  • Teller Lower Station turn into full met 3m tripod located closer to shrubs
    • soil pit
      • soil moisture @ 5, 10, 20, 30, 40 cm bgs
      • soil thermal conductivity @ 10, 20, 30, 40 cm bgs
      • soil temperature @ 10, 20, 30, 40 cm bgs
      • soil heat flux near base of active layer & plant / soil boundary
    • 1.5m soil temperature profile
    • snow depth @ tripod
    • snow depth away from tripod
    • interval camera
    • 4 component radiation
    • Spectral response sensors: NDVI & PRI up looking and two vegetation communities
    • 1.5m Air temperature, Relative Humidity, & Dew Point Temperature
    • Wind speed and direction at 3m
    • summer precipitation
      • bring out self tapping screw to keep animals from removing precip bucket lid.
  • Surface Water Station #1
    • Bring out CR200
    • Connect two Pressure Transducers to this CR200
    • Readdress them to 1 & 0 from 0 & 0
    • From temporary top site bring down for SW station:
      • instrument box
      • battery
      • solar panel
      • charge controller
  • Teller Upper Station
    • soil pit in the low area
      • soil moisture @ 5, 10, 20, 30, 40 cm bgs
      • soil thermal conductivity @ 10, 20, 30, 40 cm bgs
      • soil temperature @ 10, 20, 30, 40 cm bgs
      • soil heat flux near base of active layer & plant / soil boundary
    • 1.5m soil temperature profile
    • snow depth @ tripod
    • snow depth away from tripod
    • interval camera
    • 4 component radiation
    • 1.5m Air temperature, Relative Humidity, & Dew Point Temperature
    • Wind speed and direction at 3+m
    • summer precipitation
    • super animal protect this site.
  • Extras:
    • Survey in and place the two hobo pressure transducers somewhere in the watershed up stream from the main site.
    • Survey in temporary and permanent tripods / instrumentation
• @ Kougraok M64
  • if we get permission then site at the top perhaps?
  • If no permission then maybe a subset of instruments adjacent to the GIPL Pilgrim site and or hold off until September / the spring.
    • soil pit
      • soil moisture @ 5, 10, 20, 30, 40 cm bgs
      • soil thermal conductivity @ 10, 20, 30, 40 cm bgs
      • soil temperature @ 10, 20, 30, 40 cm bgs
      • soil heat flux near base of active layer & plant / soil boundary
    • 1.5m soil temperature profile
    • snow depth @ tripod
    • snow depth away from tripod
    • interval camera
    • 4 component radiation
    • Spectral response sensors: NDVI & PRI up looking and two vegetation communities
    • 1.5m Air temperature, Relative Humidity, & Dew Point Temperature
    • Wind speed and direction at 3m
    • summer precipitation
  • Add ground control survey point if permitted

• Existing Sites @ Kougarok
  • Remove lowest section of K-met Tower?
  • Level radiometers
  • level precip buckets
  • Refresh AT/RH sensors
  • check if Anemometers are still within specification
  • download data
  • only planning to visit 10 meter tower and Mauze Gulch (up from bridge)
  • bring out new battery

• Existing Sites @ Council
  • Remove lowest section of Tower? @ blueberry hill
  • Level radiometers
  • level precip buckets
  • Refresh AT/RH sensors
  • check if Anemometers are still within specification
  • download data
  • spend two nights with Mike Murphy to maximize field time
  • radiometer setup to Grid site
  • put in ground control point
  • Bring out new battery

• Existing Skookum Pass Repeater site
  • Switch old data logger out for CR800 and
  • if time install redundant satellite link
  • bring up two batteries

• Existing Anvil Mountain Repeater site
  • bring up two batteries
  • Change AT/RH/DP out for simpler Air temperature only

8/11

• Arrive @ around Noon
• Pick up vehicle. confirmation number 39289
• Pick up freight
• Visit Anvil Mountain and swap out batteries.
• Get groceries
• Pack vehicle for 8/12
• Pick up freight
  • bring teller coded gear to Bering Air

8/12 - 8/14 or 15

(I think this may take more than two days)
Starting to think 1.5 -2 days per site is more realistic

• Go to Teller
• @Top Put up permanent site
  • see above for instrumentation etc
• @ SW station
  • see above for instrumentation etc
• @ Snowmelt Logger
  • see above for instrumentation etc
• Use Survey GPS to lock in positions of all instrumentation (before move and after!)
• Make a discharge measurement
• Level precipitation gage
• Bring a drill & self-tapping screw to lock tipping bucket in place.

8/14 - 8/16

• FUEL UP!!!!
• If the weather cooperates, hike up and visit the Kigluaiks Sites
  • optional / cancel if behind schedule...
  • download data
  • reorient antenna if needed
• Plan A: Recon the Kougarok site
• Plan B: save Kougarok_m64 site for '17
• Plan C: put some instruments @ Pilgrim hot springs?
• @Kougarok_m64
• see above for instrumentation etc
• @ K2 Met
  • grab data off the storage module
  • sensor refresh
  • Battery
  • better secure the radiation stand to make sure it stays level.
• @ K3 Mauze Gulch
  • Sensor refresh
    • AT/RH
    • SR50A
    • Battery?
  • Data Download
• Camping Schedule on ideal itinerary
  • 8/14: Salmon Lake BLM
  • 8/15: Kougarok Cabin
  • 8/16: Kougarok Cabin

8/17 - 8/18

• Drive back to Nome
• FUEL UP!!!!
• Drive out to Council
• Spend two nights @ B&B.
• Focus on C2 Blueberry site & Tower.
• make the radiation stand more solid.
• Reduce the tower to 2 sections

8/19

• Return to Nome
• On way stop by Skookum Pass repeater
• Fix as noted above.
• Ship anything in need of shipping
• depart for Fairbanks in evening

To bring MISC

• anti seize goop
• camping gear
• putty for boxes

Hydra Probe notes

• • ID 0 = 5cm = red
  • ID 1 = 10cm = orange
  • ID 2 = 20cm = purple
  • ID 3 = 30cm = brown
  • ID 4 = 40cm = black

VATP notes

• bringing 2 drill bits (different tips), two extensions (different lengths), and two connectors
• also need to bring wrenches
• drill in UAF Nome storage
• when installing VATP, remove upper veg layer, drill a hole, install VATP, cut a slit in upper layer to place back around installed probe
• use white duct tape to secure probe to conduit

Anemometer notes

Testing each anemometer for

• propeller torque using anemometer torque disc (18310)
  • factory spec is 2.6 gm-cm (black nylon screw at 5cm and metal screw at 2cm)
    • 33821 moved with 0.2 gm-cm (a black nylon screw at 2cm radius), so this is much better than factory spec
    • 61996 moved with 0.5 gm-cm
  • tested both Clock Wise(CW) and Counter Clock Wise (CCW)
• Wind speed using anemometer drive (18802)
  • @200rpm = 0.98m/s. @1000rpm = 4.9m/s. @2000rpm = 9.8m/s
  • tested both CW and CCW
• Vane Torque using Vane Torque Gauge (18331)
  • mount the gauge, pull the string, if it moves with < 30 gm-cm of torque, golden.
  • tested both CW and CCW
• Wind Direction using Vane Angle Fixture Tower Mount (18212)
  • checked 3 directions
    • 33821 all within 1 degree of accuracy
    • 61996 reads 3 degrees less (ex: reads 177 when should be 180)

NEED ONE WIRE (have one)