Difference between revisions of "NGEE To Do Next Visit"

From IARC 207 Wiki
Jump to navigation Jump to search
Line 7: Line 7:
 
[[2018 NGEE Nome September Trip]]
 
[[2018 NGEE Nome September Trip]]
 
* SR50A transducer replacement (fall activity)
 
* SR50A transducer replacement (fall activity)
* bring out one step stool to level teller bottom radiometer.
+
* (2019) bring out one step stool to level teller bottom radiometer.
* bring out tap, die, drill, drill bit, screw for teller bottom radiometer.
+
* (2019) bring out tap, die, drill, drill bit, screw for teller bottom radiometer.
 
** screw...
 
** screw...
 
* '''also replace cnr4 desiccant since the unit didn't look like it was sealing right with this missing screw.'''
 
* '''also replace cnr4 desiccant since the unit didn't look like it was sealing right with this missing screw.'''
 
* '''Bring out additional desiccant? for box'''
 
* '''Bring out additional desiccant? for box'''
 
* '''Teller SW desiccant replacement'''
 
* '''Teller SW desiccant replacement'''
* Redrill hole for C1 Grid temperature probe
+
* (2019) Redrill hole for C1 Grid temperature probe
 
** what is needed for this?
 
** what is needed for this?
 
* Measure Creek Flow
 
* Measure Creek Flow
** salt slug, n=6 samples of 100g
+
** salt slug, n=2 samples of 50g / known volume of water
 
* Re-level radiometers
 
* Re-level radiometers
 +
* polish radiometer domes
 
* Measure thermistors resistances at Teller Bottom and add them to fieldbook.
 
* Measure thermistors resistances at Teller Bottom and add them to fieldbook.
 
** There are a couple with a 0.5C offset at spring freezing point so I think they may be failing and or something...
 
** There are a couple with a 0.5C offset at spring freezing point so I think they may be failing and or something...
Line 25: Line 26:
 
* 6/11/2018 In Fairbanks... down in 106 / the basement there is a box of 12" nails.  Would be good to grab three for the Teller SW solar panel tripod
 
* 6/11/2018 In Fairbanks... down in 106 / the basement there is a box of 12" nails.  Would be good to grab three for the Teller SW solar panel tripod
 
* I should do some experiments with the thermal conductivity thermistors in office/lab to see if I can reduce the noisiness.
 
* I should do some experiments with the thermal conductivity thermistors in office/lab to see if I can reduce the noisiness.
 +
* finish surveying vegetation plots
  
 
====Kougarok====
 
====Kougarok====
* survey veg plots?
+
* bring out a serial cable for box (removed it in fall 2018)
 +
* get a compass reading on anemometer
 +
** leave a compass in the box
  
 
====Teller SW Flow====
 
====Teller SW Flow====
* cloth tape
+
* left a metal meter stick at the site
** left a small cloth tape at the site
 
* metal meter stick or folding tape
 
** left a metal meter stick at the site
 
* flow tracker
 
 
* fieldbook
 
* fieldbook
 
* YSI conductivity meter
 
* YSI conductivity meter
 
** manual
 
** manual
 
* electrical tape
 
* electrical tape
* We (Nathan and I) set up a reach to use for salt slug method discharge estimates. 
 
  
 
==== Radiation Level:====
 
==== Radiation Level:====
Line 45: Line 44:
 
* a bit of wood to provide better base for step ladder
 
* a bit of wood to provide better base for step ladder
 
* phillips screwdriver for level
 
* phillips screwdriver for level
 +
  
 
==== Radiation Desiccant Swap:====
 
==== Radiation Desiccant Swap:====

Revision as of 12:23, 29 September 2018

To Buy

  • Step ladder for teller bottom
  • 12 volt Trimble cable

Seward Peninsula

2018 NGEE Nome September Trip

  • SR50A transducer replacement (fall activity)
  • (2019) bring out one step stool to level teller bottom radiometer.
  • (2019) bring out tap, die, drill, drill bit, screw for teller bottom radiometer.
    • screw...
  • also replace cnr4 desiccant since the unit didn't look like it was sealing right with this missing screw.
  • Bring out additional desiccant? for box
  • Teller SW desiccant replacement
  • (2019) Redrill hole for C1 Grid temperature probe
    • what is needed for this?
  • Measure Creek Flow
    • salt slug, n=2 samples of 50g / known volume of water
  • Re-level radiometers
  • polish radiometer domes
  • Measure thermistors resistances at Teller Bottom and add them to fieldbook.
    • There are a couple with a 0.5C offset at spring freezing point so I think they may be failing and or something...
    • Related: I'm wondering if the delay between measurements should be increased for the thermistor measurements.
    • Also related: perhaps add a second string up at teller top?
    • sort of some additional homework is that I saw instability in a number of thermistors when measuring up top. I suspect but haven't verified that this instability is an indicator for the wonky temperatures seen in the data but need to confirm.
  • 6/11/2018 In Fairbanks... down in 106 / the basement there is a box of 12" nails. Would be good to grab three for the Teller SW solar panel tripod
  • I should do some experiments with the thermal conductivity thermistors in office/lab to see if I can reduce the noisiness.
  • finish surveying vegetation plots

Kougarok

  • bring out a serial cable for box (removed it in fall 2018)
  • get a compass reading on anemometer
    • leave a compass in the box

Teller SW Flow

  • left a metal meter stick at the site
  • fieldbook
  • YSI conductivity meter
    • manual
  • electrical tape

Radiation Level:

  • step ladder
  • a bit of wood to provide better base for step ladder
  • phillips screwdriver for level


Radiation Desiccant Swap:

  • Step ladder
  • small CSI phillips
  • K&Z desiccant pack
  • anti-corrosion goo

Teller Top Soil Temperatures

  • Volt meter
  • fieldbook
    • learned but need to confirm that the thermistors with a capacitance are ones that are unstable and failing.

Utqiagvik

  • Intensive Site A HMP155 failed (3.5m)
  • Intensive Site B HMP155 failed (1.4m)
  • Intensive Site C HMP155 failed
  • need to replace the network cable running from the computer to the network switch. It cuts out with minimal bumping.... but station is finally back online!!!
  • Site A SR50A transducers have failed
  • some subsurface items are beginning to fail.
  • bring up clear tape and a biz card to label the computer
  • bring up the nuc plate and wood screws and other screw packet to mount nuc to wall