Seward Peninsula
2018 NGEE Nome June Trip
- SR50A transducer replacement (fall activity)
- bring out one step stool to level teller bottom radiometer.
- bring out tap, die, drill, drill bit, screw for teller bottom radiometer.
- also replace cnr4 desiccant since the unit didn't look like it was sealing right with this missing screw.
- Bring out additional desiccant?
- Teller SW desiccant replacement
- Redrill hole for C1 Grid temperature probe
- Measure Creek Flow
- Re-level radiometers
- Measure thermistors at Teller Bottom and add them to fieldbook.
- Related: I'm wondering if the delay between measurements should be increased for the thermistor measurements.
- Also related: perhaps add a second string up at teller top?
- 6/11/2018 In Fairbanks... down in 106 / the basement there is a box of 12" nails. Would be good to grab three for the Teller SW solar panel tripod
- Koug M64 Ngee tipping bucket stand is 1" aluminum pipe (verified by photo)
- Teller Bottom tipping bucket stands: 3/4" aluminum pipe (it appears)
Teller SW Flow
- cloth tape
- left a small cloth tape at the site
- metal meter stick or folding tape
- left a metal meter stick at the site
- flow tracker
- fieldbook
- YSI conductivity meter
- electrical tape
Radiation Level:
- step ladder
- a bit of wood to provide better base for step ladder
- phillips screwdriver for level
Radiation Desiccant Swap:
- Step ladder
- small CSI phillips
- K&Z desiccant pack
- anti-corrosion goo
Teller Top Soil Temperatures
Teller bottom precip bucket swap
- small csi phillips
- desiccant pack
- 2 red butt splices
- toggle bolts
- 5/16" nut driver
- 1/2" nut driver / wrench for ubolts
- crimping tool
- wire cutter
Utqiagvik
- Intensive Site C HMP155 failed
- Serial to USB Adapter seems to have shorted out recently:
[ 375.134145] usb 1-1.5: Manufacturer: Prolific Technology Inc.
[ 375.137510] pl2303 1-1.5:1.0: pl2303 converter detected
[ 375.152130] usb 1-1.5: pl2303 converter now attached to ttyUSB0
[ 375.585516] usb 1-1-port2: over-current change
[ 375.801642] usb 1-1.5: USB disconnect, device number 48
[ 375.805558] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[ 375.805712] pl2303 1-1.5:1.0: device disconnected
[ 376.041011] usb 1-1.5: new full-speed USB device number 49 using dwc_otg
[ 376.144070] usb 1-1.5: New USB device found, idVendor=0557, idProduct=2008
[ 376.144111] usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 376.144131] usb 1-1.5: Product: USB-Serial Controller
[ 376.144149] usb 1-1.5: Manufacturer: Prolific Technology Inc.
[ 376.160012] pl2303 1-1.5:1.0: pl2303 converter detected
[ 376.167664] usb 1-1.5: pl2303 converter now attached to ttyUSB0
[ 377.377778] usb 1-1-port2: over-current change
[ 377.591631] usb 1-1.5: USB disconnect, device number 49
[ 377.599560] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[ 377.599738] pl2303 1-1.5:1.0: device disconnected
[ 377.840992] usb 1-1.5: new full-speed USB device number 50 using dwc_otg
[ 377.943953] usb 1-1.5: New USB device found, idVendor=0557, idProduct=2008
[ 377.943995] usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 377.944014] usb 1-1.5: Product: USB-Serial Controller
[ 377.944031] usb 1-1.5: Manufacturer: Prolific Technology Inc.
[ 377.947508] pl2303 1-1.5:1.0: pl2303 converter detected
[ 377.961018] usb 1-1.5: pl2303 converter now attached to ttyUSB0
